Harbor Freight Tools 69719 Support Question
Harbor Freight Tools 69719 Support Question
Find answers below for this question about Harbor Freight Tools 69719 - 18 Gauge 1/4 in. Crown Stapler.Need a Harbor Freight Tools 69719 manual? We have 1 online manual for this item!
Question posted by kd092 on June 22nd, 2016
Stapler Does Not Appear To Charge With Air. Trigger Cylinder Has No Resistance
I bought the unit yesterday and went thought the instructions, made connection to air supply (140psi) does not work. the trigger pin had no pressure to it. unit is lifeless.
Current Answers
Related Harbor Freight Tools 69719 Manual Pages
User Manual - Page 2
...Eye Injury. Symbol
property or statement
pSI Pounds per square inch of pressure
cFM Cubic Feet per Minute flow
ScFM
Cubic Feet per Minute flow ...
National pipe thread, straight
WARNING marking concerning Risk of Explosion. Wear heavy-duty work gloves.
Wear NIOSH-approved dust mask/respirator. Indicates a hazardous situation which , ...69719
MAINTENANcE It is the safety alert symbol.
User Manual - Page 3
..., or medication.
contain long hair.
Do not attach the hose or tool to your finger on the trigger or connect the tool
to the air supply with finger on top of balance if the hose shifts. Always assume that the tool contains fasteners. SAFETy
SETUp
IMpORTANT SAFETy INSTRUcTIONS
INSTRUcTIONS pERTAINING TO A RISK OF FIRE, ELEcTRIc SHOcK, OR INJURy TO...
User Manual - Page 4
...trigger does not turn the tool on the tool.
b. A properly maintained tool reduces the risk of the tool or serious injury to persons. Tool service must not be performed only by qualified repair personnel. b. c.
Over pressurizing the tool may cause
bursting, abnormal operation, breakage
of binding and is unstable and can lead to persons. b. Item 69719 Any tool...
User Manual - Page 5
... other masonry products • Arsenic and chromium from chemically treated lumber Your risk from the air supply when: a. Do not remove, tamper with fasteners when any modifications to the tool maintenance instructions for triggering options.
4. Performing any portion of work area MUST wear ANSI-approved safety goggles with side shields during firing, causing them to avoid...
User Manual - Page 6
...Wear suitable gloves to the hands, arms and shoulders. Let the tool do the work .
6. SAVE THESE INSTRUcTIONS. SETUp
OpERATION
MAINTENANcE
Page 6
For technical questions, please call 1-800... (while still keeping safe control of work .
7. Use tools with the lowest vibration when there is a choice between different processes.
5. Item 69719 Grip tool as lightly as possible.
2. If ...
User Manual - Page 7
Page 7 SAFETy
Functional Description
Specifications
Maximum Air Pressure Air Inlet Air Consumption Safety Mechanism Type
Staple Type
120 PSI 1/4″ -18 NPT 0.5 CFM @ 90 PSI Single Sequential 18 Gauge, 5/8″-1-1/2″ Long, 1/4″ Crown
SETUp
OpERATION
MAINTENANcE
Item 69719
For technical questions, please call 1-800-444-3353.
User Manual - Page 8
SETUp
OpERATION
MAINTENANcE
Page 8
For technical questions, please call 1-800-444-3353. Item 69719
SAFETy
components and controls
Air Deflector
Driver Guide
Trigger
Air Inlet Plug
Magazine Release
Safety Nosepiece
Magazine
Safety Nosepiece - Also called the workpiece contact, the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object.
User Manual - Page 9
...refer to build up .
2. Note: This air tool may be long enough to prevent accidental operation. Release the tool's trigger and empty its magazine.
5. Inspect the air connections for this tool. Repair any residual air pressure, and release the trigger to reach the work area with pressure gauge, oiler, in a safe fashion after the air supply is ruptured. However, it is a good safety...
User Manual - Page 10
...Regulator D Lubricator (optional) E Coupler and Plug F Leader Hose (optional) G Air Cleaner / Dryer (optional) H Air Adjusting Valve (optional)
C
EH
G
A
Function
Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging...
User Manual - Page 11
... of use Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool
MAINTENANcE
OpERATION
SETUp
SAFETy
Page 11 Figure B: Stationary Air Supply Setup
Item 69719
For technical...
User Manual - Page 12
... not allow free movement while working . The tool must not cycle (fire).
Disconnect the tool from the air supply.
2. Hold the tool away or off of fasteners.
3. If the tool fires, stop immediately and have it repaired by a qualified service technician.
7. With the Trigger depressed, carefully lift the tool and press it again. Connect the air supply to allow access by a qualified...
User Manual - Page 13
... clean, dry cloth. Only use .
General Operating Instructions
1. Before each hour of Pneumatic Tool Oil to the airline connection before use the proper size and type of staple with side shields.
• Release the trigger. • Detach the air supply. • Attempt to fire the Tool into a piece of this tool.
2.
WARNING! TO pREVENT SERIOUS INJURy: Keep second...
User Manual - Page 14
... this manual must also wear ANSI-approved impact safety goggles with side shields.
• Release the trigger. • Detach the air supply. • Attempt to fire the Tool into a piece of scrap wood to the component manufacturers' instructions.
Item 69719
TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION, BEFORE ANy MAINTENANcE OR REpAIRS ARE DONE (including clearing...
User Manual - Page 15
... up air pressure, and leave the Magazine open Magazine. SETUp
OpERATION
MAINTENANcE
Item 69719
For technical questions, please call 1-800-444-3353. it open Magazine. Empty Magazine of the Tool.
1....approved safety goggles with side shields.
• Release the trigger.
• Detach the air supply.
• Attempt to fire the Tool into a piece of firing any built-up off the Driver...
User Manual - Page 16
...Lubricate using air tool oil and grease according to
Clearing Jams instructions. 2. Confirm staple gauge, crown, type, and length. Tighten housing assembly. Item 69719 Incorrect tool depth setting. 2. Tool empty. 3.
Clear jammed fastener according to directions. 4. Do not exceed maximum air pressure.
Check for loose connections and make sure that air supply is normal...
User Manual - Page 17
...OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
Page 17 NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY...HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
SETUp
OpERATION
MAINTENANcE
Item 69719
For technical questions, please call 1-800-444-3353. IN FACT, THE MANUFACTURER AND/OR ...
User Manual - Page 18
... Blade Pin
17 Pin
18 Driver Blade
19 Driver Blade Set
20 Collar
21 O-Ring
22 Spacer
23 Cylinder
24 Bumper
25 Gasket
26 Body
27 Nozzle
28 E-Ring
29 Pin
30 Air Seal
31 Upper Remote Housing
32 Spring
33 O-Ring
34 Remote Core
35 Remote Housing
36 O-Ring
37 Trigger Plate Pin
38 Trigger Plate
39 Trigger
40...
User Manual - Page 19
Page 19
For technical questions, please call 1-800-444-3353.
Item 69719
1
2
3
4
5
6 84 7 85 8 9 10 11 78 12 83
14 15 19 16 17 18
20 21 22 10 13 79 23
24
MAINTENANcE
25
28 26
27 30
31
32 33
80
34
33
35
36
37
81
38
...
User Manual - Page 20
... original purchaser that the defect resulted from the use of our warranty, then you . This warranty gives you specific legal rights and you with transportation charges prepaid. Limited 90 Day Warranty
Harbor Freight Tools Co.
Similar Questions
I Need An Unloader Tube For Air Compressor Serial #61693
I need an unloader tube for a central pneumatic air compressor serial number 61693
I need an unloader tube for a central pneumatic air compressor serial number 61693
(Posted by josephelliscox 1 year ago)
Where Can I Find Parts For Model 68019 Harbor Frieght Nail Gun
(Posted by Raulmartinez33 1 year ago)
I Need The Copper Pipe That Goes From Compressor To Air Tank... Item 69783. Seri
i need the copper pipe that goes from compressor to air tank itwm 69783. wheel barrow type compresso...
i need the copper pipe that goes from compressor to air tank itwm 69783. wheel barrow type compresso...
(Posted by stonyridgetigerman 2 years ago)
Difficulty Removing Piston Assm From Air Cylinder
Do you have any hints as to how to properly remove Piston Assm to initially prime unit. Pg 10 of ins...
Do you have any hints as to how to properly remove Piston Assm to initially prime unit. Pg 10 of ins...
(Posted by borowskicb 7 years ago)
My Stapler Doesn't Work.
My brand new stapler out of the box doesn't shoot the 1 1/2" staples. I hold it to a piece of wood w...
My brand new stapler out of the box doesn't shoot the 1 1/2" staples. I hold it to a piece of wood w...
(Posted by billpst 9 years ago)