Harbor Freight Tools 68861 Support Question
Harbor Freight Tools 68861 Support Question
Find answers below for this question about Harbor Freight Tools 68861 - Oscillating Multifunction Power Tool.Need a Harbor Freight Tools 68861 manual? We have 1 online manual for this item!
Question posted by Anonymous-159019 on June 10th, 2016
< Carbon Brush Replacement >
why doesn't the owners manual show how to replace the carbon brushes.
Current Answers
Answer #1: Posted by BusterDoogen on June 10th, 2016 8:58 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,397
Member since:
October 30th, 2011 Points: 28,565,397
Parts 27 - 28 on page 11 for the parts layout it should be enough to replace the brushes.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Harbor Freight Tools 68861 Manual Pages
User Manual - Page 1
...
Owner's Manual & Safety Instructions
Save This Manual Keep this manual ...68861
O S C I L L AT I N G
Multifunction
POWER TOOL
REV 13l
(Angled Cutter sold separately)
Visit our website at: http://www.harborfreight.com Email our technical support at: [email protected]
When unpacking, make sure that the product is intact and undamaged. Read this material before using this manual...
User Manual - Page 2
...
Work area safety
a.
Item 68861
Maintenance WARNING indicates a hazardous situation which may result in the warnings refers to avoid possible injury or death.
b. Power tools create sparks which , if ...In this manual, on the labeling, and all safety messages that follow the warnings and instructions may ignite the dust or fumes.
The term ″power tool″...
User Manual - Page 3
... the correct power tool for a replacement.
2. b. Any power tool that have the power tool repaired before connecting to be controlled with these instructions to a moving part of electric shock. If damaged, have the switch on the power tool. Use the power tool, accessories and tool bits etc. Service
a. Have your power tool serviced by poorly maintained power tools. If unreadable...
User Manual - Page 4
...handheld power tool, ...68861 People with pacemakers should consult their physician(s) before leaving.
7. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.)
11. Vibration Safety
This tool vibrates during use . Repeated or long-term exposure to the hands, arms and shoulders. Wear suitable gloves to reduce the vibration effects on this instruction manual...
User Manual - Page 5
...68861
For technical questions, please...manual before using more than one extension cord for 2-Prong Plug
Extension Cords
1. WARNING marking concerning Risk of Fire.
Double Insulated Tools: Tools with Two Prong Plugs
Outlets for more than a 16 gauge cord. (See Table A.)
4. When using it repaired by a qualified electrician. Always replace...outdoor use the tool if the power cord or plug...
User Manual - Page 6
...68861
Maintenance Turn the Power Switch off and unplug the tool from the tool.
Tool Set Up
Hex Wrench
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool... the beginning of this manual including all text under subheadings therein before set up or use of this product. Functions
Power Switch
Setup
Operation
Spindle
...
User Manual - Page 7
... clean. Angled Cutter
4. General Operating Instructions
1. Do not apply excessive pressure on the spindle. Then unplug the tool from its off , remount it, making sure that the holes on the tool, slide the Power Switch forward.
3. Item 68861
For technical questions, please call 1-888-866-5797. Designate a work .
6. Secure loose work area with enough...
User Manual - Page 8
....
AFTER USE, clean external surfaces of the Tool. If abnormal noise or vibration occurs, have the unit serviced and Carbon Brushes replaced by a qualified service technician. Item 68861 The Angle Scraper and Cutting Blade should not be performed only by a qualified technician. Cleaning, Maintenance, and Lubrication
1.
If the Power Cord of moving parts, cracked or broken...
User Manual - Page 9
... its own rate.
2. If breaker is tripped, make sure circuit is unpowered, turn off tool and check circuit breaker.
Performance
1. Carbon brushes worn
or damaged. Replace as needed .
2. Eliminate use of motor using compressed air.
4. Page 9 Likely Solutions
1. Check power at least 10 ft-lb. Internal damage or
3. Cap screw not tight enough. Excessive noise...
User Manual - Page 10
...ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. Parts List...
24 Pull Brace
25 Link Plate
26 Plastic Housing
27 Brush Holder
28 Carbon Brush
29 Screw (ST3.5X10)
30 Switch
31 Switch Holder
32...68861
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT...
User Manual - Page 11
Safety
Setup
Assembly Diagram
13 14
16
18
15
12
17
11
19
10
20
21
9
22
8
23
7
6
24
25
5
26
27 4
3
28
32 33 34
35
2
29 36
30
1
31
F
41
E
39
40
42
38
43
37
Operation
Maintenance
Item 68861
For technical questions, please call 1-888-866-5797. Page 11
User Manual - Page 12
... IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. Limited 90 Day Warranty
Harbor Freight Tools Co. If our inspection verifies the defect, we will return repaired products at our election..., injuries to the original purchaser that the defect resulted from state to us with a replacement. Proof of purchase date and an explanation of this product is free from defects in no...
Similar Questions
Saw Will Not Turn On
We have 62757 wet tile saw which is not turning on anymore. checked power all seems good.
We have 62757 wet tile saw which is not turning on anymore. checked power all seems good.
(Posted by tdesai65 1 year ago)
Carbon Brush Size For Central Machinery 16 Inch Scroll Saw Variable Speed
what are the Carbon brush size for Central machinery 16 inch scroll saw variable speed
what are the Carbon brush size for Central machinery 16 inch scroll saw variable speed
(Posted by rickyray1983 1 year ago)
Lubrication Of The 62279 Oscillating Multifunction Power Tool
Instructions on how to and where to lubricate the above power tool, and what to use for the lubricat...
Instructions on how to and where to lubricate the above power tool, and what to use for the lubricat...
(Posted by denisemarieloeffel 3 years ago)
My 44141 Die Grinder Needs A New Switch And Carbon Brushes.
I contacted Harbor Freight. They sent me an email stating that the brushes were available from them ...
I contacted Harbor Freight. They sent me an email stating that the brushes were available from them ...
(Posted by laloward 9 years ago)
Carbon Brushes
where can I buy carbon brushes for this wet saw (69275)
where can I buy carbon brushes for this wet saw (69275)
(Posted by mamudepaula 9 years ago)