Harbor Freight Tools 62757 Support Question
Harbor Freight Tools 62757 Support Question
Find answers below for this question about Harbor Freight Tools 62757 - 7 in. 1.5 HP Bridge Wet Cut Tile Saw.Need a Harbor Freight Tools 62757 manual? We have 1 online manual for this item!
Question posted by tdesai65 on April 18th, 2023
Saw Will Not Turn On
We have 62757 wet tile saw which is not turning on anymore. checked power all seems good.
Current Answers
Answer #1: Posted by SonuKumar on April 18th, 2023 7:05 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,648,140
Member since:
May 9th, 2021 Points: 16,648,140
If your Harbor Freight Tools 62757 wet tile saw is not turning on even though the power supply seems to be fine, there are a few things you can check to troubleshoot the issue:
- Check the power switch: Make sure the power switch on the saw is turned on. Sometimes, the switch can get stuck or become faulty, preventing the saw from turning on.
- Check the blade guard: Ensure that the blade guard is properly engaged. The saw will not turn on if the guard is not in place or is not properly engaged.
- Check the power cord: Make sure the power cord is not damaged or frayed. If it is, it may need to be repaired or replaced.
- Check the blade: If the blade is damaged or dull, the saw may not turn on. Inspect the blade and replace it if necessary.
- Check the motor brushes: If the motor brushes are worn out, the saw may not turn on. Remove the motor brushes and inspect them for wear. If they are worn down, they will need to be replaced.
- Check the circuit breaker: If the saw is not turning on, it may have tripped the circuit breaker. Check the circuit breaker box and reset the breaker if necessary.
If none of these steps resolve the issue, it may be best to contact Harbor Freight customer support or a professional power tool repair technician for further assistance.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Harbor Freight Tools 62757 Manual Pages
User Manual - Page 1
... herein may not be drawn proportionally. Copyright© 2015 by Harbor Freight Tools®. Tools required for the safety warnings and precautions, assembly,
operating, inspection, maintenance and... manual and the receipt in any shape or form without the express written consent of Harbor Freight Tools. SAVE THIS MANUAL. Keep this product. No portion of purchase if product has no number)....
User Manual - Page 2
...62757
For technical questions, please call 1-888-866-5797.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. TABLE A
4. USE RIGHT TOOL. When using an extension cord, be kept safe distance from tool before turning...good condition. Don't use the next heavier gauge. USE PROPER EXTENSION CORD. If in doubt, use power tools... mask if cutting operation is ... checking...
User Manual - Page 3
...to whether the tool is unintentionally contacted.
13. If repair or replacement of parts,
15. check for
personnel if the grounding instructions are NOT safety glasses. TURN POWER OFF. Check with or without ...120 VAC Grounded Tools: Tools with an electric cord having an outer surface that it comes to operate tool.
18. In the event of injury to 15 A)
Item 62757
For technical ...
User Manual - Page 4
... unfinished cut, center the blade in 125 VAC 3-Prong Plug and Outlet.
8. This plug will fit in the workpiece. Wear eye protection.
2. b. d. e. A sudden reaction to a pinched,
bound, or misaligned blade, causing an uncontrolled workpiece to install the proper outlet. Spreader - Check guards for proper operation with saw disconnected from power before turning on the saw if...
User Manual - Page 5
...to one side of the tool plug or receptacle getting wet, position tile saw . Wash hands
Item 62757
For technical questions, please... extension cord before turning on the tool.
Avoid unintentional starting. If the plug or receptacle does get wet, DON'T unplug ...and nameplates on the tool.
11. Use only extension cords that has been approved by power sanding, sawing, grinding, drilling, ...
User Manual - Page 6
... common sense and caution are factors which cannot be built into this product, but must be supplied by the operator that may occur.
Page 6 Item 62757
For technical questions, please call 1-888-866-5797.
It must be understood by the operator. WARNING: This product contains di (2-ethylhexyl) phthalate (DEHP), a chemical known...
User Manual - Page 7
... .
7. Include vibration-free periods each day of it).
Wear suitable gloves to the hands, arms and shoulders. Grip tool as lightly as possible.
2. Item 62757
For technical questions, please call 1-888-866-5797. Use tools with the lowest vibration when there is a choice between different processes.
5. Repeated or long-term exposure to vibration...
User Manual - Page 8
... sure the Power Switch of the Tile Saw is unplugged from the electrical outlet prior to assembly, adding accessories, or making any kind of the manual.
Be sure to wear heavy-duty work gloves when making adjustments to 45° in 2.5° Increments - WARNING! With assistance, set the Tile Saw upright. (See Figure B.)
Item 62757
For...
User Manual - Page 9
Item 62757
For technical questions, please call 1-888-866-5797. The Adjusting Knob (123) is located at the bottom of 5.
Turn the Adjusting Knob clockwise
... Stand (111) and into the threaded hole as shown.
8. Secure Knobs. Attach the Handle (4) to keep the Tile Saw stand
and Washers (3). (See Figure C.)
balanced evenly on the floor. (See Figure B.)
(120) (123)
Figure B
Attaching...
User Manual - Page 10
... E
Figure H
Figure F (59)
(120)
Figure G
Note: Bolts should be placed onto the Bolts from outside, through the leg stand and into the wheel. Lift the saw stand with the front handle to move it, as shown in Figure I
Item 62757
For technical questions, please call 1-888-866-5797. Wheel Assembly
1.
User Manual - Page 11
... packaging during shipment. Fill Water Tray (60) with enough clean, cold water to performing maintenance or relocating the Tile Saw. (See Figure J.)
To Fill And Drain The Water Tray:
1. Note: The Right Rail Stand (111) is not continuous.
2. Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of this product.
User Manual - Page 12
... (37) to spin up to its electrical outlet. Continue moving the Saw Blade (37) over the tile. (See Figure N.) 8. Then, remove the cut is completed. (See Figure N.) 9. Turn the Power Switch (18) to full speed. (See Figure M.)
Saw Blade (37)
Tile
Figure N
Item 62757
For technical questions, please call 1-888-866-5797. Always wear eye protection. Position the...
User Manual - Page 13
...62757
For technical questions, please call 1-888-866-5797.
Hold the tile against the Guide and slide the Guide down the Scale Rail (105). (See Figure O.) 3. Then, retighten the two Knobs, and two bolts. (See Figure P.)
2. For a 45 degree cut the tile...clearing the Filter of the Tile Saw. Loosen the Knob (75) on the Angle Cutting
Guide (102) and position the Angle Cutting Guide at the desired ...
User Manual - Page 14
...Saw Blade (not included). Item 62757
For technical questions, please call 1-888-866-5797. Always
unscrew and remove the Nut (39) by turning it
use Continuous Rim Diamond Saw Blades
clockwise. Page 14 With one of the provided Wrenches, hold the end of the Tile Saw...work
(32)
gloves to avoid cuts to expose the Saw Blade. (See Figure R.)
3. Make sure the Power Switch (37) of
Figure S...
User Manual - Page 15
... same direction as that of the
original position. Page 15 Do not overtighten. (See Figure R.)
Item 62757
For technical questions, please call 1-888-866-5797. IMPORTANT: When installing a Saw Blade (37),
8. Fasten the Nut by turning it counterclockwise until snug.
Carefully lower Blade Guard (41) back into its
make sure the "ARROW" depicted...
User Manual - Page 16
...Tile Saw. Do not immerse any debris on the inner left side of the Frame.
When finished, replace the Inner Cover,
of the tool to the Filter and Impeller which will not produce a satisfactory cut... (52).
Item 62757
For technical questions, please call 1-...OPERATION: Turn the Power Switch of Tile Saw is ...wet/dry vacuum cleaner or compressed air to keep dried debris from Saw...
User Manual - Page 17
No power at outlet.
2. Check power at outlet. Check shaft for illustration purposes only, and are not available individually as replacement parts. Replace blade with hot/warm water 3. Check shaft for run with cold water
Follow all safety precautions whenever diagnosing or servicing the tool.
Item 62757
For technical questions, please call 1-888-866-5797. Replace brushes 1....
User Manual - Page 18
...
18 Power Switch...
37 Saw Blade ...Bracket
1
101 Angle Scale ( C )
2
102 Angle Cutting Guide
1
103 %XWWHUÀ\.QRE
1
104 Big Flat...4
119 Support Stand I
4
120 Support Stand Ii
2
121 Height Adjustable Leg
1
122 Elastic Pin
1
123 Adjusting Knob
1
124 Adjusting Plate
Item 62757
For technical questions, please call 1-888-866-5797. Qty 1 1 1 4 9 2 2 1 8 1 2 1 2 8 12 12 1 1 1 1 1...
User Manual - Page 19
Item 62757
For technical questions, please call 1-888-866-5797. Page 19 ASSEMBLY DIAGRAM
Please Note: Saw Blade (37) is sold separately and not included.
User Manual - Page 20
Limited 90 Day Warranty
Harbor Freight Tools Co. We shall in materials and workmanship for incidental, contingent, special or consequential damages arising from state to persons or property, or for the period ...
Similar Questions
Carbon Brush Size For Central Machinery 16 Inch Scroll Saw Variable Speed
what are the Carbon brush size for Central machinery 16 inch scroll saw variable speed
what are the Carbon brush size for Central machinery 16 inch scroll saw variable speed
(Posted by rickyray1983 1 year ago)
A Replacement Tray For A Harbor Freight Tools 62382 - 7 In. 1.5 Hp Bridge Tile
Where can I purchase a replacement tray for the model tile saw listed above? [email protected]
Where can I purchase a replacement tray for the model tile saw listed above? [email protected]
(Posted by danielwprior 1 year ago)
Need 102 Outer Fllange For Chicago Electric 10” Sliding Compound Miter Saw Ite
looking for outer flange for Chicago electric 19" sliding compound miter saw item 61972
looking for outer flange for Chicago electric 19" sliding compound miter saw item 61972
(Posted by nelliethedog1 2 years ago)
A Bad Plastic Gear That Turns Wet Wheel
any ideas on how to find and new one or better one
any ideas on how to find and new one or better one
(Posted by Joe37866 4 years ago)
Saw Dust Blower Not Working
How do I get air from the saw dust blower?
How do I get air from the saw dust blower?
(Posted by daltoriom 5 years ago)