Home » Haier » Air Conditioners » Haier HB6000VD1M22-EP

Haier HB6000VD1M22-EP Support Question

Find answers below for this question about Haier HB6000VD1M22-EP.
Need a Haier HB6000VD1M22-EP manual? We have 1 online manual for this item!

Haier Overview Questions Manuals Reviews Videos Research

Question posted by nate4843 on July 30th, 2015

My Hb6000vd1m22,blower Shorted, I Replaced It But It Won't Run,

do you have a wiring diagram

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TechSupport101 on July 30th, 2015 5:17 PM

This answer was accepted by the poster of the original question.

TechSupport101

Member since:
May 24th, 2013

Points: 12,171,305

1,100
points

There is a Service Manual for the model here that should be of great assistance.

www.satechhelp.co.za

Related Haier HB6000VD1M22-EP Manual Pages

User Manual - Page 1

... SHOULD BE USED WHEN INSTALLING OR MODIFYING THIS APPLIANCE, UNLESS OTHERWISE NOTED IN THESE INSTRUCTIONS. IF IN DOUBT CONTACT YOUR LOCAL AUTHORITIES. Installation & Operation Manual Air Handler 13 SEER 2 3 4 5 Ton WARNING WHEN THIS APPLIANCE IS INSTALLED IN AN ENCLOSED AREA, SUCH AS A GARAGE OR UTILITY ROOM, WITH ANY CARBON MONOXIDE PRODUCING...

User Manual - Page 2

... immediately to the transportation company. INDEX TOPIC Index Physical dimensions Replacement Parts Source Installation Requirements Air Flow Orientation Horizontal Left-Hand Instructions Refrigerant Tubing Condensate Removal Electrical Connections Thermostat Wiring Orifice Change Circulating Air Duct Blower Performance Start-up Regular Maintenance Model Number Explanation PAGE 2 3 6 6 7 8 9 10...

User Manual - Page 6

... igniting flammable vapors, must be installed in unconditioned spaces where sweating may generate a glow, spark or flame capable of vehicles. REPLACEMENT PARTS SOURCE Replacement parts are available through local distributors.When ordering replacement parts, give the COMPLETE model and serial numbers shown on a platform when deemed necessary. When more than one appliance is...

User Manual - Page 7

..., and install insulation kit on vertical ( donut shape ) drain pan. *Upflow Discharge *Air Handler is factory ready for Upflow & Horizontal Right Discharge Application for 3*4*5 as shown. *Air Handler is factory ready for Upflow & Horizontal Left Discharge Application for 2 as shown. 7 AIR FLOW ORIENTATION *Horizontal Right Discharge Tube and Drain conn. front Horizontal Left...

User Manual - Page 8

...Traps must be provided by pouring water into channel bracket at the rear of the cavity. 6) Replace the J-shape metal bracket or brackets on the vertical drain pan and place the plastic oval gasket... brazing see page 13 or read the Warning label on horizontal drain pan. Fig.2 8 Air flow Secondary Knockout Primary Knockout Plastic Drain cover Fig.1 oval gasket WARNING: If incorrect knockouts ...

User Manual - Page 9

...with the seams sealed. Use of water, as a condensate line adequate caution must be the "running" type, or "R" type. A joint compound should have provisions for each unit. The total ...Styrofoam and certain types of these materials. A trap must not be adequately elevated to the air handler. UNIT DRAIN CONNECTION FLEXIBLE TUBING-HOSE OR PIPE 2" MINIMUM 3" MINIMUM A POSITIVE LIQUID...

User Manual - Page 10

... above is installed refer to the Air Handler as the rating plate, included in the optional heat kit must be installed within sight of local code, the National Electrical Code. When an optional heat kit is only for that kit. The use of the unit. The wiring diagram included in the heat kit...

User Manual - Page 11

... the air supply mode, switch can adopt different power switch show diagram 2. Note: Thermostat C : COM. This mode is RUN SWITCH ...Air Diagram 1 Conditioning open /stop , hot control Environment temperature, can adopt multi-connect switch or select switch. THERMOSTAT WIRING For Thermostat Control Environment-temperature and Air Conditioning open /stop , the wiring diagram as shown diagram...

User Manual - Page 12

... mode is control the indoor unit & cooling only outdoor unit at the same time no air supply mode. The detailed infor see the following diagram 6. For Thermostat Control Environment-temperature and Air Conditioning open /stop , the wiring diagram as shown diagram 4. Note: Thermostat C: COM. Thermostat can adopt multi-connect switch or select switch. If need select...

User Manual - Page 13

... 3) Remove the check piston to prevent infiltration. or tighten 1/6 turn. 10) Replace suction line grommet and insulation. standards. When passing through an unconditoned space it is...NUT SUCTION LINE WITH SPIN CLOSURE WHITE TEFLON SEAL PISTON CIRCULATING AIR DUCT RUBBER GROMMET Air duct systems should be replaced before any tubing connections are made. FOLLOW THESE INSTRUCTIONS TO ...

User Manual - Page 14

...1366 1328 1290 1252 1800 1745 1690 1635 1580 1525 1850 1795 1740 1685 1630 1575 The air delivery can be checked by the following method; (The optional Heat Kit must be in place... or decreased it may be varied by adjusting the blower speed tap as shown on the wiring diagram. 14 The CFM can be done by changing the blower speeds. This measurement should be done in various locations...

User Manual - Page 15

... in a garage or where flammable vapors may be installed. Return air is not to allow for drainage. It is protected from any ...maintained on a regular basis by the user is cleaned or replaced. Auxiliary drain is installed, when necessary, and pitched to insure...only item to be present. Unit is connected. Low voltage wiring is elevated when installed in place and secured. Drain pans ...