Genie PowerMax 1500 Support Question
Genie PowerMax 1500 Support Question
Find answers below for this question about Genie PowerMax 1500.Need a Genie PowerMax 1500 manual? We have 1 online manual for this item!
Question posted by ericmblecknerciv on May 28th, 2013
Thermal Protector
My garage Opener model 2024 is only 2 years old. The geeen LED staerted blinking 5 times in sequence. The instruction manual says it may be the Thermal Protector not re-setting. I cannot find out where it is and the instructions do not reference it anywhere. The door will operate normally for a few times after unplugging and re-plugging it in. I also re-set all the limits. Is the circuit board bad? and where is the Thermal Protector?
This is very frusterating
Thanks,
Eric
Current Answers
Related Genie PowerMax 1500 Manual Pages
Owner's Manual - Page 1
... to persons or damage to property - Need help or have questions? GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900,
SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200
SCREW/BELT/CHAIN DRIVES
OPERATION & MAINTENANCE MANUAL
Includes INTELLICO®DE 2 Remote Control.
For use only with a one...
Owner's Manual - Page 3
... NOT connect the operator to the source of power until instructed to the door before removing opener cover.
For products having an emergency release, mount the emergency
release within reach, but a
avoiding contact with the door opener. B) At a minimum height of opening while door is used throughout this manual. If you reading the information in Death or Serious...
Owner's Manual - Page 4
... allow manual opening . Review Assembly/Installation Instructions poster. You can also go to www.geniecompany.com to download a PDF file.
The door stops and reverses to fully open position if anything passes through the garage.
The wall console has an indicator light with an object. Home Link and Car2U® compatible. Refer to ensure all models) Some...
Owner's Manual - Page 5
... only used to make sure there are no objects in the garage door opening and closing your garage door.
Remote Programming synchronizes your remote control devices (remotes, wall console, and keypad) with the buttons, LED indicators and products used to need to follow to set up your garage door opener for operation:
1. These buttons should NOT be used to program...
Owner's Manual - Page 6
...
WARNING
• Make sure doorway is in view and clear of the step and start over. Closing Garage Door (Down Limits)
1 Lift the door open by hand until the shuttle/bullet
engages the carriage on blue (round LED remains off). Severe damage to the opener can restart as many times as necessary to carriage, do so now.
Owner's Manual - Page 8
...ON. Open/Close Button Opens and closes door from inside garage. Independent Light Control Button Controls door opener lights from other manufacturers may not work with openers of ...Manual-ScrewBeltChain-EN indd 8
7/13/12 10 17 AM MODEL AC SR3 FCC ID: B8Q AC SR3 IC: 2 33A-CS 1D
THE GENIE COMPANY Residential Door Operator
120V. 60HZ. 5A
S/N:10XXXX XXXXXXX
Wall consoles from inside garage...
Owner's Manual - Page 9
... adjustments to the fully OPEN position. Red LED lights on the Wall Console.
Then repeat the WALL CONSOLE/Contact Reverse Test, steps 11-13.
Force and Speed Limits are factory programmed and automatically set themselves when you use the Wall Console to open and close the garage door for the first time automatically sets the Force needed...
Owner's Manual - Page 10
... for additional information on purple).
- +
10
G999-393 Manual-ScrewBeltChain-EN indd 10
PROGRAM
SET
- +
NOTE: Do NOT hold the Program Set button (the round
LED turns blue).
16 Remove protective film for battery from Intellicode 2 to the beginning of time and must be programmed separately, following instructions are for the remote control transmitters ("Remotes") provided...
Owner's Manual - Page 11
.... Repeat as described in the HomeLink® instruction manual.
19 Press and release the same button on the remote
(both LED's flash blue and then turn off). PROGRAM
SET
- 3 Required Programming
18 Press and release the same button on the remote
(the door should open or close). G999-393 Manual-ScrewBeltChain-EN indd 11
11
7/13/12...
Owner's Manual - Page 12
... full instructions packed with the keypad. 12
1. Enter your new PIN, press Program key . Note: If you fear it may have successfully erased the old programming.
2. 4 Optional Programming
PROGAMMING THE WIRELESS KEYPAD
Setting Up a PIN
1. Press in "Setting Up a Pina"nd"Programming. Press Program key . Opener LEDs will stay on the Powerhead indicates an error. Door opener will...
Owner's Manual - Page 13
...-393 Manual-ScrewBeltChain-EN indd 13
(continued next page) 13
7/13/12 10 17 AM
PROGRAM
- +
3 Press up arrow button (+) and down arrow
button (-) simultaneously on the Powerhead and
hold 2 seconds, round LED comes ON. NOTE: The garage door opener will not activate the door opener.
4 Optional Programming
Clearing Memory FOR Remotes
1 Press the Program Set button on...
Owner's Manual - Page 14
...® instructions for operation with 10 or higher, the Learn Code Button and Indicator LED are located near the antenna.
The light lens may need to
the Powerhead. The LED color displayed on your opener.
Press and hold the button for this Intellicode® 1 model of Genie® garage door openers .The default Intellicode® 2 setting must be opened . This...
Owner's Manual - Page 15
...
1a Screw drive models:
One-Piece Doors will only accept a straight door arm. Attaching door arm to 2" lag bolts. (Bolts, nuts, and screws not furnished.)
3/8"-16 x 7/8" Bolt
3/8" Lock nut
Straight door arm (not included)
1b Chain/belt drive models:
One-Piece Doors will only accept a straight door arm. Door bracket
Cotter pin
Straight door arm
G999-393 Manual-ScrewBeltChain-EN indd...
Owner's Manual - Page 16
... a 1-1/2" high object (or a 2" x 4" board laid flat) at the center of travel, retest door opener. See your door springs serviced.
• Close the door. (continued next page)
G999-393 Manual-ScrewBeltChain-EN indd 16
7/13/12 10 17 AM SAVE THESE INSTRUCTIONS
WARNING
• Garage door hardware (springs, cables, brackets, pulleys, etc.) are under extreme pressure and tension.
•...
Owner's Manual - Page 17
... to carriage, pull down and back towards opener and let go )
• Chain/belt drive models: Verify bullet is installed and Limits are not pinched or
near moving parts.
1.
Replace battery. 3.
Pull/release cord down and toward the opener. Close powerhead light cover. 2.
Reconnect power to door opener. • Open powerhead light cover. • Remove light...
Owner's Manual - Page 19
... BLUE
OFF Flashes BLUE 3 Times
Then the Current Speed setting for OPENING travel will cross. • Place the Source (Red LED) Safe-T-Beams on heavier sectional doors. Speed settings should not need adjustment with condition of the garage receives direct sunlight. • Position the Source (Red LED) on the direct sunlight side
Multiple Garage Doors • NEVER position Safe-T-Beam...
Owner's Manual - Page 21
... if limits are properly set . See pages 6-7. • Check Sure-Lock™. If not, check fuse or circuit breaker.
• If power is OK. -
See pages 8-9. • Check garage door for reversed, broken or cut insulation and short wires. Door opener starts for normal operation. See page 13.
21
G999-393 Manual-ScrewBeltChain-EN indd 21...
Owner's Manual - Page 22
... are tight. • Be sure garage door is in . Door opener runs slow.
• Check operating condition of Safe-T-Beam® pair and nearest other Safe-T-Beam® pair, see page 10. Contact a trained door system technician. Safe-T-Beam® signal interference.
Thermal cutout
Program remote using instructions on a one -piece door. • Contact The Genie Company at...
Owner's Manual - Page 23
...1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers, ("...time, measured from the date of FIFTEEN (15) YEARS CHAIN- Seller warrants all accessories included with product for a period of ONE (1) YEAR...
OPENER MODEL: _____
REMOTE CONTROL MODEL: _____
DEALER NAME: _____
DEALER ADDRESS:_____
G999-393 Manual-ScrewBeltChain...
Owner's Manual - Page 24
...
Check out NEW ACCESSORIES and PRODUCTS;
enables safe parking in garage
Universal Wall Push Button • Easy to door -
G999-393 Manual-ScrewBeltChain-EN indd 24
™ 7/13/12 10 17 AM Garage Door Opener Accessories
Looking for activation
Upgrade with Revolution Series 1500, 1200 and 1000 Models)
• Sleek and compact design
• Beeps and flashes green...
Similar Questions
What Remote Do I Use For Powerlift Garage Door Opener Model Wr77 Serial No.08258
(Posted by tmski87 3 years ago)
I Have A Model Isd 995 That Has The Green Light Blinking 2 Times.
I have disconnected the ribbon cable and reinserted it, it cycles up and down then wont operate agai...
I have disconnected the ribbon cable and reinserted it, it cycles up and down then wont operate agai...
(Posted by sramsland 7 years ago)
Where Is The Reset Button On Genie Garage Door Opener Powermax 1500
(Posted by jpIJac 9 years ago)
Powermax 1500 Revolution Series Model 4062
Door opener will open with both remotes and via the wireless keypad outside mounted. It will NOT clo...
Door opener will open with both remotes and via the wireless keypad outside mounted. It will NOT clo...
(Posted by brianmaclennan 9 years ago)
Led Lights Do Not Come On Unit When Setting Limits?
LED lights do not come on when setting limits?
LED lights do not come on when setting limits?
(Posted by Petuniamate 11 years ago)