GE 51207 Support Question
GE 51207 Support Question
Find answers below for this question about GE 51207 - Smart Home Wireless Motion Sensor Alarm.Need a GE 51207 manual? We have 1 online manual for this item!
Question posted by cclown77 on August 15th, 2011
Why Does The Alarm Hesitate To Activate When Motion Is Detected, Ge 51207
Why does the alarm hesitate to activate instantly whem motion is detected?
Current Answers
Related GE 51207 Manual Pages
User Manual - Page 1
Personal Security
Motion Sensor with Remote User Manual
Do not use in wet locations
User Manual - Page 2
Motion Sensing Alarm
With Remote Control
Wall Mount
Indicator Light Keychain Remote
Motion Sensing Alarm Alarm/Chime Switch
Low Battery Indicator The Motion Sensing Alarm has a low battery indicator light. Average battery life for typical usage is up to be replaced, the indicator light will flash slowly. If the batteries need to one year.
User Manual - Page 3
...the remote control The Remote Control requires a CR2032 battery (included).
Installing batteries in the Alarm The battery compartment is one year.
1.
Insert (3) AA batteries (not included) . Average... in the direction of the unit.
1. Replace the cover and secure screw.
INSTALLING BATTERIES The Remote Controlled Motion Sensing Alarm requires 3 AA Alkaline batteries (not included).
User Manual - Page 5
Press the LEARN button. Battery Compartment
Learn
Learn
Button
2. Locate LEARN button.
LINKING THE REMOTE TO THE ALARM Make sure you have installed the batteries before proceeding.
1. Remove the battery compartment screw and slide off cover in the direction of the open arrow.
User Manual - Page 6
... the main unit and secure screw. The alarm will sound a single short tone, and the light will now respond to the remote.
.
The ball and socket mount will provide the flexibility to the battery compartment of the alarm unit and press the ARM button. Replace cover to aim the motion sensor in standby mode. NOTE...
User Manual - Page 7
... location, such as the corner of 110˚ horizontal x 70˚ vertical. Recommended installation height is 6 to the Secure ball and socket mount to 8 feet.
20'
15'
110˚
10'
5' Feet
6'-8'
70˚
Feet
5'
10'
15'
20'
2. detection zone, with approximate angles of the room. This will provide maximum coverage.
1. NOTE: The...
User Manual - Page 8
... the side of the remote.
Locate the ALARM/CHIME switch on the wall, slide insert bracket of mount into a wall stud.
Chime
Alarm
2. OPERATING IN THE ALARM MODE
1. The mount will click when secured to ALARM mode. Slide switch to the alarm.
wall using either the provided wall anchors or by screwing directly into the back...
User Manual - Page 9
... tone and a red light will sound again. When motion is detected, the siren will flash. The delay allows time for motion. There will repeat until the unit is armed. Point the remote control at the front of the alarm and press the ARM button. The siren will activate in 30 seconds. In 15 seconds the...
User Manual - Page 10
... front of hearing damage. If the remote control with the correct security code is sensed.
1. 11
Disarming the Alarm When returning to the protected area, the unit will beep once if motion is not used to cover the alarm to reduce risk of the alarm unit and press the DISARM button within 30 seconds, the...
User Manual - Page 11
ACTIVATING THE CHIME Activate the chime by pointing the remote control at the alarm and pressing the 'ARM' button. DEACTIVATING THE CHIME Deactivate the chime by pointing the remote control at the alarm and pressing the 'DISARM' button.
Chime
Alarm
2.
PANIC FEATURE For immediate alarm with no delay, aim Slide switch to notify you when motion is sensed...
User Manual - Page 12
...alarm housing, use a soft To turn off the panic alarm, aim the remote at front of the alarm and press the DISARM button. Set remote to ALARM mode.
After initial chime, wait 15 seconds and wave hand in front of the alarm...To discontinue test, point remote at the front of alarm and press DISARM.
If chime sounds immediately, the sensor is working properly.
3. Set remote to CHIME mode...
User Manual - Page 13
...provide an adequate warning, or that such an event will prevent any alarm product, including expensive commercial systems, it may be outside of a product's designed range... and certain environmental conditions may impact performance and audible alarm signals may reduce the risk of Alarm Products
This product should protect themselves with water and wipe dry.
...
User Manual - Page 14
Memorial Road, Oklahoma City, OK 73114.
51207 5/08 15
WARNING Risk of the General Electric Company and is a trademark of personal injury • Prolonged exposure to Jasco Products Company LLC, 10 E.
This Jasco product comes with a 90 day limited warranty.
is used under license to alarm siren may cause
permanent hearing loss Battery...
Similar Questions
How To Reset The Codes? Ge 80-307-3x Wireless (adt Was Provider)
I just moved into this home built in '97. Previous owner didn't leave the code and left it unplugged...
I just moved into this home built in '97. Previous owner didn't leave the code and left it unplugged...
(Posted by Dkrebs7186 8 years ago)
How Do I Determine The Master Code Of My Ge Networx 148e Home Alarm System?
(Posted by duLen 9 years ago)
How Do I Replace The System Battery Of The Ge Simon 3?
(Posted by sinoffbisprof 12 years ago)