Garmin GMI 10 Digital Marine Instrument Display Support Question
Garmin GMI 10 Digital Marine Instrument Display Support Question
Find answers below for this question about Garmin GMI 10 Digital Marine Instrument Display.Need a Garmin GMI 10 Digital Marine Instrument Display manual? We have 5 online manuals for this item!
Question posted by gazza0352 on February 15th, 2012
Hours Run By Honda Motor
hi does the gmi 10 show hours off running time for a honda 150 motor 2011 model
Current Answers
Related Garmin GMI 10 Digital Marine Instrument Display Manual Pages
Important Safety and Product Information - Page 2
... these guidelines to ensure safe navigating.
• When navigating, carefully compare information displayed on the unit to determine if your product contains or accepts maps, or to...charts and notices to mariners contain all available navigation sources, including information from visual sightings, local waterway rules and restrictions, and maps. Battery Warnings Your GPS unit may use the ...
Installation Instructions, S/N 19Wxxxxxx - Page 1
...or (800) 800-1020; Select a location. 2. Flush mount the GMI 10. 3. January, 2008
190-00892-02 Rev. GMI 10 Installation Instructions
To obtain the best possible performance, install your GMI 10 Marine Instrument according to the following items. If any questions while installing or using your GMI 10.
Serial number
Contact Garmin Contact Garmin if you experience difficulty...
Installation Instructions, S/N 19Wxxxxxx - Page 2
...after refining the hole. If
you
will fit in the location at
which you mount the GMI 10 has sufficient open space behind the case. • Is at least a
3-inch (8 cm... the cutout.
6. Use a file and sandpaper to refine the size of the cables for the GMI 10 is not exposed to flush mount the GMI 10.
2. There should be
cutting
the
hole
with
a
jigsaw,
and
not
a
3
/17 32
...
Installation Instructions, S/N 19Wxxxxxx - Page 3
...from 3/32 to 3/8
from 0.76 to 2.03 from 2.28 to drill a clearancecounterbore through the GMI 10 into place. Note: During a typical installation, use 18 AWG wire.
Note: Stainless-steel screws may...an AGC/3AG - 1 A fuse. To 8-32 Vdc boat supply
-
+
To GMI 10
Fuse Block Caution: The GMI 10 maximum input voltage is recommended to use a countersink bit to 9.52
Fiberglass-all thicknesses
...
Installation Instructions, S/N 19Wxxxxxx - Page 4
... network on the diagram.) 3. If the included drop cable is connected directly.
GMI 10 Installation Instructions Caution: If you need to extend the NMEA 2000 backbone, connect an ... NMEA 2000 Network 1. Installation Instructions
To install the wiring harness: 1. Step 4: Connect the GMI 10 to a NMEA 2000 network. For more information on the boat, route the
positive connection through...
Installation Instructions, S/N 19Wxxxxxx - Page 5
...T-connector (included)
NMEA 2000 device
(not included)
Drop cable (included)
Existing NMEA 2000 network
Connecting the GMI 10 to an Existing NMEA 2000 Network
Ignition or in-line switch
Fuse
+
-
12 Vdc battery
Power cable
... and building a NMEA 2000 network, visit www.garmin.com. • The GMI 10 is not powered by the NMEA 2000 network, it must be separately connected to the power source...
Installation Instructions, S/N 19Wxxxxxx - Page 6
...
GPS 17/17x NMEA 0183 HVS Antenna
GMI 10 Device
>
WIRE COLOR
Fuse RED 1 A BLACK
BROWN GREEN
- + Battery
12 Vdc
WIRE
RED POWER GND NMEA GND
Tx/A (+)
Tx/B (-)
>
NMEA 0183 Compliant Device
>
>
Notes:
Wiring the GMI 10 to a Standard NMEA 0183 Device
• Consult the installation instructions for extended runs of wire. Installation Instructions
Connecting the GMI 10...
Installation Instructions, S/N 19Wxxxxxx - Page 7
... Function Transmit/Receive PGN List Group Function Product Information
The GMI 10 is NMEA 2000 certified
NMEA 0183 Sentence Information
The GMI 10 can be received and transmitted by a GMI
10 when communicating with a NMEA 2000-compliant device. Installation Instructions... Group Function Transmit/Receive PGN List Group Function System Time Product Information Vessel Heading Engine Parameters -
Installation Instructions, S/N 19Wxxxxxx - Page 8
...States of America.
© Copyright 2008 Garmin Ltd.
Software License Agreement
BY USING THE GMI 10, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THE FOLLOWING SOFTWARE LICENSE ... gasketed, high-impact plastic alloy, waterproof to IEC 529 IPX7 standards
Power GMI 10 power input source: 8-32 Vdc
Fuse:
AGC/3AG - 1 A
GMI 10 power usage: 2.5 W max
NMEA 2000 Power Input: 9-16 Vdc
NMEA...
Installation Instructions, S/N 1Y3xxxxxx - Page 1
... (optional)
To install and use your package includes the following instructions. Flush mount the GMI 10 (page 2.
3. A
Printed in a safe place. Keep the original sales receipt, or...GMI 10 Installation Instructions
To obtain the best possible performance, install your GMI 10 Marine Instrument according to the following items. If any questions while installing or using your GMI 10. The GMI 10...
Installation Instructions, S/N 1Y3xxxxxx - Page 2
... the center punch, indent the center of each of the hole.
4.
Place the GMI 10 into the cutout to refine the size of the four mounting-hole locations.
6. This...shock. • Allows room for the routing and connection of the cables. Step 1: Select a Location for the GMI 10
Consider the following tools:
• Phillips screwdriver
• Drill and 1/8 in. (3.2 mm) drill bit for ...
Installation Instructions, S/N 1Y3xxxxxx - Page 3
...Garmin recommends applying an anti-galling, stainless anti-seize lubricant to the T-connector and the GMI 10. Determine where you just added to the ignition switch of the boat if possible, or...you disconnected.
4. Connect to the side of the T-connector you would like to connect the GMI 10 to your existing NMEA 2000 network: 1.
Add the included T-connector for each sensor (not...
Installation Instructions, S/N 1Y3xxxxxx - Page 4
... included)
T-connector (included)
NMEA 2000 device
(not included)
Drop cable (included)
Existing NMEA 2000 network
Connecting the GMI 10 to an Existing NMEA 2000 Network
Ignition or in-line switch
Fuse
+
-
12 Vdc battery
Power cable
T-connectors
Female... To learn more about NMEA 2000 and building a NMEA 2000 network, visit www.garmin.com. • The GMI 10 is powered by the NMEA 2000 network...
Installation Instructions, S/N 1Y3xxxxxx - Page 5
The GMI 10 displays the received data, but cannot transmit the data to another NMEA 0183 device or transmit the data to your NMEA 0183-compliant device to a Garmin GPS 17/17x antenna.
GMI 10 Device
Color
Function
Black
Yellow
>
Blue
>
White
Brown
Green
> >
GMI 10 Data Cable
Accessory Off(-) Accessory On(+)
Tx/A(+) Tx/B(-) Rx/A(+) Rx/B(-)
GMI 10 Device
WIRE COLOR...
Quick Start Manual - Page 4
... on your boat. You can also be displayed as an analog gauge. Selecting an Instrument Screen Category Change the instrument screen to the sensors on an instrument, such as a GPS 17x, the GMI 10 can quickly cycle through NMEA 2000 or NMEA 0183. From the instrument screen, select Menu > Setup > Set Instrument Type.
GMI 10 Quick Start Manual
For example, when...
Quick Start Manual - Page 5
...that category. Choose from the categories listed below.
• Surface-GPS or water speed, GPS heading or magnetic sensor heading, and odometer.
• Water-... voltage, hours, neutral indicator, and status indicators. Cycling Through Instrument Screens in a Category When viewing a category, use the soft keys under the left and right arrows to cycle through instrument screens
GMI 10 Quick Start...
Quick Start Manual - Page 6
...,
select Menu.
2. For example, if you have a GPS antenna and a heading sensor, you want to change.
GMI 10 Quick Start Manual To change the source sensor, select Source, and choose the sensor you want to use. To change the appearance of an instrument screen:
• If the instrument screen is showing a number, select Menu > Show...
Quick Start Manual - Page 10
...GPS position.
• True-sets true north as the heading reference.
• User Magnetic-allows you can select units of measure, language, enter total fuel capacity, and so on the GMI 10, from the following options to determine when the GMI 10...the appropriate settings or enter the necessary values. GMI 10 Quick Start Manual
Choose from the instrument screen, select Menu > Setup > System....
Quick Start Manual - Page 14
... values for the sensor. From the instrument screen,
select Menu > Setup > NMEA 2000 Devices. 2.
Tip: For more information on the GMI 10. 1. Select the appropriate sensor.
Honda Engine ECO Symbol
The symbol appears when boats with NMEA 2000-compatible Honda engines are running in a fuel-efficient mode and engine RPM is displayed. You will see information about...
Quick Start Manual - Page 15
...
NOTE: There are several possible engine alarms. If the GMI 10 displays an engine alarm, contact your Honda engine manual to determine if the engine is using the DBT sentence which does not include keel offset.
Do not drive or operate the boat while the GPS device is in Demo mode.
Simulating Operation-the unit...
Similar Questions
How Do I Go Into Simulation Mode On A Garmin Marine Gps Modle741xs
how do I use simulation mode on a garmin 741xs marine ver
how do I use simulation mode on a garmin 741xs marine ver
(Posted by Curthupp 6 years ago)
Can The Gmi 10 Be Set At Home Before Going On The Water ?thx Jon
(Posted by Anonymous-58453 11 years ago)
Can The Gmi 10 Be Set On Ground
(Posted by Anonymous-58453 12 years ago)
Power And Navagation Issue
gps does not show movement when going,shows area but only a question mark,also shuts off a few times...
gps does not show movement when going,shows area but only a question mark,also shuts off a few times...
(Posted by deannalogan 12 years ago)
Gmi 10 Switches Off After Few Hours
Hello, my new GMI 10 installed in my new sailing yacht initially works well, but switches off with b...
Hello, my new GMI 10 installed in my new sailing yacht initially works well, but switches off with b...
(Posted by hannojelden 12 years ago)