Fujitsu MHT2030AT Support Question
Fujitsu MHT2030AT Support Question
Find answers below for this question about Fujitsu MHT2030AT - Mobile 30 GB Hard Drive.Need a Fujitsu MHT2030AT manual? We have 1 online manual for this item!
Question posted by chris31439 on April 29th, 2012
How Can I Connect This Drive
I took this drive out of a iBook G4 that's dead. What kind of connector do I need to plug it in as an external drive?
Current Answers
Related Fujitsu MHT2030AT Manual Pages
Manual/User Guide - Page 5
... specifications of the MHT Series, 2.5-inch hard disk drives.
Preface
This manual describes MHT2080AT/ MHT2060AT/ MHT2040AT/ MHT2030AT/ MHT2020AT models of the disk drive. CHAPTER 4 Theory of Device Operation This chapter describes the operation theory of the systems in controller that need to be understood to incorporate the drives into user systems. This manual assumes that...
Manual/User Guide - Page 6
... the text, the alert signal is centered, followed below by external magnetic fields. The main alert messages in the text are the...Binary numbers are represented normally. Ensure that the disk drive is an example:
(Example)
Data corruption: Avoid mounting the disk drive near strong magnetic sources such as a "hard disk drive," "HDD," "drive," or "device" in the "Important Alert Items."
...
Manual/User Guide - Page 9
... but hold it too hard, the cover and the spindle motor contact, which
may occur if the user does not perform the procedure correctly. Ensure that the disk
drive is not affected by ... handling the device, disconnect the body ground (500 kΩ or greater). Pressing
it by external magnetic fields. Important Alert Items
Important Alert Messages
The important alert messages in this manual are...
Manual/User Guide - Page 14
... Conditions 3-1
3.1 Dimensions 3-2
3.2 Mounting 3-3
3.3 Cable Connections 3-9 3.3.1 Device connector 3-9 3.3.2 Cable connector specifications 3-10 3.3.3 Device connection 3-10 3.3.4 Power supply connector (CN1 3-11
3.4 Jumper Settings 3-11 3.4.1 Location of setting jumpers 3-11 3.4.2 Factory default setting 3-12 3.4.3 Master drive-slave drive setting 3-12 3.4.4 CSEL setting 3-13...
Manual/User Guide - Page 18
... system configuration 2-3 Figure 2.3 2 drives configuration 2-4
Figure 3.1 Dimensions 3-2 Figure 3.2 Orientation 3-3 Figure 3.3 Mounting frame structure 3-4 Figure 3.4 Location of breather 3-5 Figure 3.5 Surface temperature measurement points 3-6 Figure 3.6 Service area 3-7 Figure 3.7 Handling cautions 3-8 Figure 3.8 Connector locations 3-9 Figure 3.9 Cable connections 3-10 Figure 3.10...
Manual/User Guide - Page 21
The disk drive is 2.5-inch hard disk drives with built-in this chapter, and specifications and power requirement are described. CHAPTER 1 Device Overview
1.1 Features 1.2 Device Specifications...11 Advanced Power Management
Overview and features are described in disk controllers. C141-E192-02EN
1-1 These disk drives use the AT-bus hard disk interface protocol and are compact and reliable.
Manual/User Guide - Page 22
...drive supports an external data rate up to 40 GB (formatted) on one disk using the RLL recording method and 30 recording zone technology. The Sound Pressure level is 24dB(A), as measured 0.3 m from the drive...drive has a formatted capacity of 80 GB (MHT2080AT), 60 GB (MHT2060AT), 40 GB (MHT2040AT), 30 GB (MHT2030AT) and 20 GB (MHT2020AT) respectively.
(3) High-speed Transfer rate
The disk drive ...
Manual/User Guide - Page 23
... a diagnostic function to the disk media.
This cache system enables fast data access. C141-E192-02EN
1-3 1.1 Features
1.1.3 Interface
(1) Connection to ATA interface The disk drive has built-in controllers compatible with the read-ahead cache system described in item (3) and the write cache described in the buffer can be transferred ...
Manual/User Guide - Page 24
...• Minimum (Track-Track) • Average • Maximum (Full)
80 GB
60 GB
40 GB
30 GB
156,301,488 117,210,240 78,140,160 58,605,120
512
4,200 ...rpm ± 1%
7.14 ms
1.5 ms (typ.) Read: 12ms (typ.)
22 ms (typ.)
20 GB...MHT2080AT MHT2060AT MHT2040AT MHT2030AT MHT2020AT
Format Capacity (*1) Number of the disk...
Manual/User Guide - Page 25
... (2/2)
Model
Capacity (*1)
No. of the drive being replaced.
of Sectors 63 63 63 63 63
1.2.2 Model and product number
Table 1.2 lists the model names and product numbers of model names and product numbers
Model Name MHT2080AT MHT2060AT
MHT2040AT MHT2030AT MHT2020AT
Capacity (user area)
80 GB 60 GB
40 GB 30 GB 20 GB
Mounting screw
Order No.
The...
Manual/User Guide - Page 30
...cable.
(2) Mean time to repair (MTTR)
The mean time to repair (MTTR) is 30 minutes or less, if repaired by external factors, such as follows:
Total operation time in Subsection 3.2 for five years or 20,000...operation, whichever occurs first. When the DE surface temperature exceeds 48 °C, the disk drives requires no overhaul for five years when the DE surface temperature is less than 48 ...
Manual/User Guide - Page 31
...drive without user's retry and ECC corrections shall occur no more than 10 times when reading data of 1014 bits. The product supports the Emergency Unload a minimum of 300,000 normal Load/Unload cycles. C141-E192-02EN
1-11 Read retries are executed.
• Hard...the head on the disk. The user need not be concerned with alternates when the disk drive is assumed that the data blocks to ...
Manual/User Guide - Page 35
C141-E192-02EN
2-1
CHAPTER 2 Device Configuration
2.1 Device Configuration 2.2 System Configuration
This chapter describes the internal configurations of the hard disk drives and the configuration of the systems in which they operate.
Manual/User Guide - Page 37
... uses a LSI chip for the read/write preamplifier. The drive has a 44pin PC AT interface connector and supports PIO mode 4 transfer at 16.6 MB/s, Multiword DMA mode 2 transfer at 16.6 MB/s and also U-DMA mode 5 (100 MB/s).
2.2.2 1 drive connection
MHT2080AT MMHHTC22006302AATT MMHHTC22004400AATT MHT2030AT
Figure 2.2 1 drive system configuration
C141-E192-02EN
2-3 The highspeed microprocessor unit...
Manual/User Guide - Page 39
...
C141-E192-02EN
3-1 CHAPTER 3 Installation Conditions
3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings
This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. For information about handling this hard disk drive and the system installation procedure, refer to the...
Manual/User Guide - Page 45
Pressing it by external magnetic fields. Mounting screw hole
Cable connection
Mounting screw hole Figure 3.6 Service area
Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage...
Manual/User Guide - Page 61
... service is necessary, the disk drive positions the head to maintain disk drive stability. If the disk drive receives a command execution request from the hard disk controller (HDC) with the...generator in writing. The command execution wait time is about 3 seconds.
Each channel is connected to execute the command without waiting for write nonlinearity generated at reading. C141-E192-02EN
...
Manual/User Guide - Page 149
...the host. Self-test has ended with "Servo Check," error. Self-test has ended with "SMART Drive Error Log Check," "Random Read Test," or "Read Scan Test" error. C141-E192-02EN
5-75...execution status
Bit 0 to 3:
4 to BFh
Meaning Off-line data acquisition is interrupted by a soft/hard reset from the host.
Self-test is not executed.
Off-line data acquisition has ended without an ...
Manual/User Guide - Page 228
Operations
• Upon receipt of a hard reset • Upon receipt of the command. • A reset is issued in the sleep mode. The drive enters the standby mode under the standby mode ...idle, or low power idle mode because the access to the disk medium cannot be made immediately. The drive enters the sleep mode under the following condition:
• A SLEEP command is issued, response time ...
Manual/User Guide - Page 247
... DRDY DRQ DSC DWF
dB A-scale weighting Disk enclosure Device/head register Drive ready Ddata request bit Drive seek complete Drive write fault
E
ECC Error checking and correction ER Error register ERR Error
F
FR
Feature register
H HA Host adapter
HDD Hard disk drive
IDNF IRQ14
I
ID not found Interrupt request 14
L LED Light emitting diode...
Similar Questions
Fujitsu Mhw2080at - Mobile 80 Gb Hard Drive
How many cylinders, heads and sectors have the mobile hard drive Fujitsu MHW2080AT???
How many cylinders, heads and sectors have the mobile hard drive Fujitsu MHW2080AT???
(Posted by elkohrastralro 6 years ago)
Hard Drive Not Connecting To Laptop
(Posted by estellev03 9 years ago)
Are These Hard Drives Used In Sony Vaio Laptops?
(Posted by almariaricobucao 12 years ago)
Mhs2030at Driver
i need the driver-install.exe for my hard drive (MHS2030AT) reason: i want to install the hard dr...
i need the driver-install.exe for my hard drive (MHS2030AT) reason: i want to install the hard dr...
(Posted by traveler1987 13 years ago)
