Fujitsu MHW2080AT Support Question
Fujitsu MHW2080AT Support Question
Find answers below for this question about Fujitsu MHW2080AT - Mobile 80 GB Hard Drive.Need a Fujitsu MHW2080AT manual? We have 1 online manual for this item!
Question posted by elkohrastralro on May 14th, 2017
Fujitsu Mhw2080at - Mobile 80 Gb Hard Drive
How many cylinders, heads and sectors have the mobile hard drive Fujitsu MHW2080AT???
Current Answers
Answer #1: Posted by BusterDoogen on May 14th, 2017 12:24 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,447
Member since:
October 30th, 2011 Points: 28,565,447
No. of Cylinder: 16383 No. of Heads: 16 No. of Sectors: 63
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Fujitsu MHW2080AT Manual Pages
Manual/User Guide - Page 1
...
3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings
This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E144
C141-E250
3-1 For information about handling this hard disk drive and the system installation procedure, refer to the following Integration Guide.
Manual/User Guide - Page 2
Installation Conditions
3.1 Dimensions
Figure 3.1 illustrates the dimensions of the disk drive and positions of the mounting screw holes. All dimensions are in mm.
Figure 3.1 Dimensions
3-2
C141-E250
Manual/User Guide - Page 3
...
For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)."
(1) Orientation The disk drives can be 0.49N•m (5kgf•cm). Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction.
(2) Frame
The MR head bias of mounting
Note) These dimensions are...
Manual/User Guide - Page 5
... points
Table 3.1 Surface temperature measurement points and standard values
No. 3.2 Mounting
(4) Ambient temperature
The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface temperature from the disk drive.
Measurement point
Temperature
1
DE cover
60 °C max
C141-E250
3-5
To check the cooling efficiency, measure the surface temperatures...
Manual/User Guide - Page 6
...external magnetic fields. Damage: Do not press the cover of the disk drive. Ensure that the disk drive is not affected by the edges.
(6) Handling cautions
Please keep the ...circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Installation Conditions
(5) Service area Figure 3.5 shows how the drive must be accessed (service areas) ...
Manual/User Guide - Page 8
Installation Conditions
3.3 Cable Connections
3.3.1 Device connector
The disk drive has the connectors and terminals listed below for connecting external devices.
Figure 3.7 shows the locations of these connectors and terminals. Connector, setting pins
PCA
Figure 3.7 Connector locations
3-8
C141-E250
Manual/User Guide - Page 9
... Take note of the following precaution about plugging an interface cable (socket) into the interface connector of the disk drive and plugging the connector into a host receptacle: − When plugging together the disk drive interface connector and
the host receptacle or interface cable connector (socket), do not apply more than 10 kgf...
Manual/User Guide - Page 10
Installation Conditions
3.3.4 Power supply connector (CN1)
Figure 3.9 shows the pin assignment of the jumpers to select drive configuration and functions.
Figure 3.10 Jumper location
3-10
C141-E250 Figure 3.9 Power supply connector pins (CN1)
3.4 Jumper Settings
3.4.1 Location of setting jumpers
Figure 3.10 shows the location of the power supply connector (CN1).
Manual/User Guide - Page 11
Open
1
CA
2
DB
Open
(a) Master drive
1
CA
Open
Short
2
DB
(b) Slave drive
Figure 3.12 Jumper setting of master or slave drive
Note: Pins A and C should be open. Open
Figure 3.11 Factory default setting
3.4.3 Master drive-slave drive setting
Master drive (disk drive #0) or slave drive (disk drive #1) is selected.
C141-E250
3-11 3.4 Jumper Settings
3.4.2 Factory default setting...
Manual/User Guide - Page 12
Open
1
CA
2
DB
Short
Note: The CSEL setting is identified as a slave drive. The drive is not depended on setting between pins Band D. Thus, since the slave drive is not connected to the CSEL conductor, the CSEL is identified as a master drive. Figure 3.13 CSEL setting
Figure 3.14 and 3.15 show examples of the slave...
Manual/User Guide - Page 13
C141-E250
3-13 3.4 Jumper Settings
drive Figure 3.15 Example (2) of cable select
drive
3.4.5 Power up in standby setting
When pin C is grounded, the drive does not spin up at power on.
Similar Questions
L Need The Driver For The Hard Drive Fujitsu Mhv2080ah 80 Gb Driver
fujitsu MHV2080AH 80 GB l need the driver for it thanks
fujitsu MHV2080AH 80 GB l need the driver for it thanks
(Posted by pauls144 12 years ago)
Retreve Data From Fujitsu Hard Drive Model Mhy2160bh
My Toshiba lap top died and does not power up anymore, Howcan I retreve data fromthe hard drive to m...
My Toshiba lap top died and does not power up anymore, Howcan I retreve data fromthe hard drive to m...
(Posted by JohnB1126 12 years ago)
Are These Hard Drives Used In Sony Vaio Laptops?
(Posted by almariaricobucao 12 years ago)
Driver For Fujitsu Hard-drive Model Map3367np For Window Nt.
I have got a PC with WINDOW NT for controlling work station. During operating it does not recognise ...
I have got a PC with WINDOW NT for controlling work station. During operating it does not recognise ...
(Posted by onkarsingh431 13 years ago)
Hard Drive Prob
hi tve got advrnt 6411 i did up dates shut down laptop normal and now it dont boot powers uo to blac...
hi tve got advrnt 6411 i did up dates shut down laptop normal and now it dont boot powers uo to blac...
(Posted by billy001 13 years ago)