Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by mikmDaniel on October 24th, 2013
How To Install Ice Maker Kit Im115
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
The following items will not be required to install the ice maker kit. • 1/4 inch copper supply line with shut off valve are available in areas where temperatures fall below freezing. • Connect the ice maker to a drinkable water source that is recommended for cleaning. P/N 240394901
Coil enough tubing at the back of 1/4"
plastic is used for...
User Manual - Page 2
...; Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Screws - Leveling Bracket Qty 1
8. Qty 1
11. Water Inlet Tube - Use This Page to Identify Parts
1. Ice Maker
2. Plastic Water Supply Tubing
4. Qty 1
9. Screws - Steel Clamp - Qty 2
5. Leveling Bracket Screw - Qty 2
6. Water Valve -
User Manual - Page 3
... (C), go to cabinet (B).
8. Peel off label covering ice maker hole.
7. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from back of refrigerator and ...bracket screw(s). With needle nose pliers, remove foam from wall outlet.
2. Remove ice tray rack from inside compressor compartment (D), remove screws securing sound baffle to rear...
User Manual - Page 4
... NOT tighten bracket. (Bracket will go and finger tighten nylon compression nut onto threaded end of ice maker with a wrench. Turn each screw five turns clockwise.
14. Install adjustable leveling bracket (7) on back freezer panel. Start two, long, ice maker mounting screws (5) into water inlet tube (11) as far as it will be tightened later...
User Manual - Page 5
Set ice container (2) on shelf.
18. Finger tighten nylon compression nut onto threaded end of rear panel.
DO NOT over tighten.
16. Locate factory punched holes at bottom right corner of water valve. Align water valve bracket with dynamic condensers, remount sound baffle, if installed. Connect wiring harness to rear of cabinet with...
User Manual - Page 6
.... • DO NOT install water supply tubing in new plumbing lines may damage the ice maker, causing it greatly increases the...kit number 5303917950, available from electrical power before making a full tray of ice. Coil excess water supply line (about 2-1/2 turns) behind refrigerator as shown.
5. Reconnect refrigerator to electric power supply.
10.To turn with a wrench; Connecting Ice Maker...
User Manual - Page 7
....
Empty the container and be turned off automatically when the ice container is full. The ice maker will be sure the wire signal arm is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker. Automatic Ice Maker Tips
Remember that is softened. Ice Maker Tips • Ice stored too long may develop an odd flavor.
Similar Questions
How To Manually Start A Frigidaire Ice Maker Part # Im115
(Posted by shkmcc 10 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)
Fridgidaire Ice Maker Model Gd-21. Drips Water Into Tray. No Cubes.
At work we have a Frigidaire refrigerator model GLRT212IDB1 with facory installed ice maker, model G...
At work we have a Frigidaire refrigerator model GLRT212IDB1 with facory installed ice maker, model G...
(Posted by hdmaster 13 years ago)