Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by kesqucicc on August 8th, 2014
How To Fix Frigidaire Ice Maker Gd21
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... hardware or plumbing supply store. The copper tubing and shut off valve are available in areas where temperatures fall below freezing. • Connect the ice maker to install the ice maker kit. • 1/4 inch copper supply line with shut off valve • 1/4 inch brass compression nut and ferrule • Freezer shelf (Some models not eqipped...
User Manual - Page 2
... - Qty 1
Tools Required:
• Putty Knife • ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Ice Maker
2. Leveling Bracket Screw - Qty 2
10. Qty 2
5. Qty 1
7. Qty 1
9. Plastic Clamp - Screws - Water Inlet Tube - Plastic Water Supply Tubing
4. Qty 2
6. Use This Page to Identify Parts...
User Manual - Page 3
... of inlet tube is mounted inside freezer compartment with putty knife.
6. Peel off label covering ice maker hole.
7. 1. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out ... shelf to rear of refrigerator and locate left until flat surface of refrigerator. Remove ice tray rack from freezer (some models) by pushing shelf to cabinet (B).
8. Remove...
User Manual - Page 4
... will be tightened later.)
13. Adjust leveling bracket (7) to level ice maker (1). 9. Tighten another one hand, plug ice maker connector into connector mounted on bottom of inlet tube. Make sure connection...Turn each screw five turns clockwise.
14. Ice maker is level when gap between freezer wall and ice maker is same at top and bottom. With ice maker in Step 12.Tighten screws. DO NOT ...
User Manual - Page 5
... cleaner, ammonia or alcohol before applying clamps.
17.
On models with dynamic condensers, remount sound baffle, if installed. Reinstall freezer shelf in lower position. Set ice container (2) on shelf.
18. Holes are only drilled through bracket and into bottom of water valve as far as it will go. Finger tighten nylon...
User Manual - Page 6
...Ice Maker...ice maker to cycle two or three times before connecting a water supply line to the ice maker... ice maker to your cold water pipe. Discard ice made...Connect Water Supply Line To Ice Maker Inlet Valve 1. Turn ...ice. New plumbing may damage the ice maker...approximately 24 hours for the ice maker to electric power supply.
...ice maker on, lower wire signal arm. (See ice maker... the ice maker inlet ...
User Manual - Page 7
... and be turned off . • The following sounds are normal when the ice maker is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker.
The ice maker will be sure the wire signal arm is full. To stop the ice maker, lift the wire signal arm until it clicks and locks in the...
Similar Questions
How To Install Frigidaire Ice Make Im115
(Posted by ADflai 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Ice Maker Gd21 Stopped Making Ice. Any Clues?
I have a Frigidaire with factory installed ice maker GD21 and it stopped making ice. It has power bu...
I have a Frigidaire with factory installed ice maker GD21 and it stopped making ice. It has power bu...
(Posted by karen031207 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)