Frigidaire FRQE7000LW Support Question
Frigidaire FRQE7000LW Support Question
Find answers below for this question about Frigidaire FRQE7000LW.Need a Frigidaire FRQE7000LW manual? We have 3 online manuals for this item!
Question posted by wiibuka on May 5th, 2013
Flashing Lights. Runs For A Few Senconds And It Shutsdown.
I first notice that the leds on the front controls started flashing on their own. When I use it, it will run for about 1min and then stops and the leds in the controls start flashig. When I finally get it running it will dry for about 10 mins, then starts to beeb, stop and again the flashing lights. Please help.
Current Answers
Answer #1: Posted by OnlineOutreachSpecialist on May 7th, 2013 10:18 AM
OnlineOutreachSpecialist
Member since:
March 30th, 2011 Points: 2,848,320
Member since:
March 30th, 2011 Points: 2,848,320
Hello wiibuka - I understand the lights are flashing and dryer will not complete cycle. Try resetting the unit by either unplugging it or flipping the household breaker to the off position. Wait approximately two minutes, turn on the dryer and select a normal cycle. If these troubleshooting steps prove ineffective, you may wish to contact a professional as the unit may possibly have a defective cord, wiring, control board or door switch.
Online Outreach Specialist
Related Frigidaire FRQE7000LW Manual Pages
Wiring Diagram (All Languages) - Page 1
... 4 and the second digit would flash twice indicating the 2 and the START indicator light will pause for the second digit. Clear code, exit mode and start flashing at fault. Remove wires from dryer. If reading is within 50 K (± 10%), check wiring between thermistor and electronic control. Measure resistance of times the lights flash. If reading is within 50...
Wiring Diagram (All Languages) - Page 2
... reset for six seconds. 3. heat source is lit. heat source is pressed, all the Option LED's should light. When the Pause Cancel button is off . heat source is displayed.** 6 turns: Drive motor runs; Control thermistor reading is off . Dryer will toggle back
and forth in on door switch plunger) and placing a finger on the both...
Installation Instructions (All Languages) - Page 1
All about the
Installation
of your Dryer
TABLE OF CONTENTS
Important Safety Instructions 2-3 Reversing Door 18-19 Installation Requirements 4-10 Accessories 20 Installed Dryer Dimensions 11 Español 21 Installation Instructions 12-17
137371800A (1006)
Installation Instructions (All Languages) - Page 2
...or area of all of the following instructions before installing and using this appliance: • Destroy the carton and plastic bags after the dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 ... venting materials are known to light any appliance. • Do not touch any appliance. Do not stack washer on pedestal. Place all other appliance. This dryer is not recommended for commercial ...
Installation Instructions (All Languages) - Page 3
... SAFETY INSTRUCTIONS
WARNING
Please read thoroughly
‰ Door latches and drum tumbles when cycle starts
‰ Registration card sent in
3 Obey all instructions before initial
operation
Door Reversal
...setting solid on all corners
Gas Supply (Gas Dryer)
‰ Manual shutoff valve present in
Final Checks
‰ Installation Instructions and Use and Care Guide read all safety messages that...
Installation Instructions (All Languages) - Page 4
... SRDT rated at 240 volt AC minimum, 30 amp, with 4 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. time delay fuses or circuit breakers. See "Grounding requirements" in Canada have factoryinstalled, 4-wire power supply cord (NEMA 14-30R).
4
Individual 30 amp...
Installation Instructions (All Languages) - Page 5
... gas supply piping system at test pressures in Electrical Installation section. Individual, properly polarized and grounded 15 amp. POWER SUPPLY CORD -
The tubing MUST be used to connect your dryer to natural gas, causing gas leaks. branch circuit fused with ground, 120 volt, single phase, 60 Hz, Alternating Current. The...
Installation Instructions (All Languages) - Page 6
... of any other obstruction. INSTALLATION REQUIREMENTS
Exhaust system requirements
Use only 4 inch (102 mm) diameter (minimum) rigid or flexible metal duct and approved vent hood which has a swing-out damper(s) that open when the dryer is free of fire. When the dryer stops, the dampers automatically close to follow these instructions can...
Installation Instructions (All Languages) - Page 7
...exhaust system. Do not exhaust dryer into the laundry area.
Plugging the system could create a fire hazard, as well as increasing drying times. Use an approved vent hood to ...work and creating a fire hazard as well as increase drying times. A clothes dryer produces combustible lint. If the dryer is not exhausted outdoors, some fine lint will be expelled into a chimney,...
Installation Instructions (All Languages) - Page 8
..." (9.5 cm) installation. • Venting upward with normal usage.
Dryer vent elbows are available through an uninsulated area may expose the exhaust system to down ) and start the dryer.
3 Read the measurement on the next page.
Í NOTE
Use of 90° quick-turn 90° dryer vent elbow directly to exhaust outlet of the exhaust...
Installation Instructions (All Languages) - Page 9
... (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSAZ240 MH.
2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will obstruct the flow of combustion and ventilation air. 3 On carpet. This provision is to be...
Installation Instructions (All Languages) - Page 10
... to be vented straight back to achieve 0" (0 cm) rear installation.
0" (0cm)
0" (0cm)
3" (7.6cm)
60 sq.
INSTALLATION REQUIREMENTS
Clearance requirements, continued
Installation in a Recess or Closet
1 A dryer installed in a bedroom, bathroom, recess or closet, MUST be exhausted outdoors.
2 No other fuel burning appliance shall be installed in a closet with equivalent air openings...
Installation Instructions (All Languages) - Page 11
... supply on rear of unit
centerline height for rear vent
39" (99cm)
* To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right or down on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. Leftward venting of exhaust on pedestal-mounted or freestanding...
Installation Instructions (All Languages) - Page 12
...installed by a path of electrical current this appliance. For a grounded, cord-connected dryer:
1 The dryer MUST be run with this manual for the proper power cord to be installed onto
power cord. ...shock. • Do not use an extension cord with the circuit conductors and connected to the pre-installation requirements in this dryer. Locate the dryer within reach of the receptacle...
Installation Instructions (All Languages) - Page 13
...outlet, have a proper outlet installed by a qualified electrician. Gas dryer (USA and Canada)
1 The dryer is equipped with a three-prong (grounding) plug for electrical current.
2 ...If it will reduce
the risk of electrical shock. For a grounded, cord-connected dryer: 1 The dryer MUST be plugged into an appropriate outlet that is properly grounded. Grounding requirements -
If...
Installation Instructions (All Languages) - Page 14
... is not available, test all pipe connections. Do not block access to flow through the gas line. to dryer
Shutoff Valve Open position
from gas supply line to move through the pipe. Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for gas to the 3/8 inch (0.96 cm) pipe located...
Installation Instructions (All Languages) - Page 15
...slot below the access panel. Tighten both screws securely.
Neutral terminal
IMPORTANT
If moving dryer from the center terminal back to the GREEN screw next to the terminal block.
15... cord neutral (center wire) conductor to the SILVER colored center terminal on the back of the dryer. 3 Install a UL-approved strain relief according to the outer, BRASS colored terminals on the ...
Installation Instructions (All Languages) - Page 16
... the screw securing the terminal block
access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in...NEMA 14-30 type ST or SRDT, through the strain relief. 5 Disconnect the internal (WHITE) dryer harness ground wire from the (GREEN) ground screw next to the terminal block. 6 Attach the ground...
Installation Instructions (All Languages) - Page 17
... 8). Grounding type wall receptacle
Do not, under any questions during initial operation, please review the "Avoid Service Checklist" in a location near the dryer for service. 7 Place these instructions in your Use & Care Guide before plugging the power cord into an outlet.
3 Plug the power cord into a grounded outlet. 4 Turn on all other...
Product Specifications Sheet (English) - Page 2
...Controls Dryer Drum Interior Interior Light Door Trim Ready Steam™ DrySense™ Technology Wrinkle Release Technology TimeWise™ Technology Moisture Sensor Time Remaining Indicator Cycle Status Lights Cycle Signal Cycle Signal "On/Off " Cycle Signal Volume Control Control Lock Start / Pause / Cancel Buttons Energy Saver Option Delay Start...
Optional Accessories
Dryer Stacking Kit 15...
Similar Questions
Frigidaire Dryer Beeps Three Times And Wont Start
(Posted by smewaltja 9 years ago)
Dryer Stops After 10 Mins, No Heat, But Will Run On 'air Fluff.'
Frigidaire AGQ6000ES2, about 3 years old. The dryer stops after 10 mins after I start it, there is a...
Frigidaire AGQ6000ES2, about 3 years old. The dryer stops after 10 mins after I start it, there is a...
(Posted by morningtreat 10 years ago)
The Dryer Will Not Start, No Lights, But The Light Inside Is On When Door Is Ope
(Posted by dboland27 11 years ago)
Error Code 62
Started dryer...ran for about 20 minutes...then flashed error code 62 and stopped working
Started dryer...ran for about 20 minutes...then flashed error code 62 and stopped working
(Posted by LKHudd 12 years ago)