Frigidaire FRQE7000LW Support Question
Frigidaire FRQE7000LW Support Question
Find answers below for this question about Frigidaire FRQE7000LW.Need a Frigidaire FRQE7000LW manual? We have 3 online manuals for this item!
Question posted by Anonymous-94162 on January 15th, 2013
Remove Top Cover To Replace Dryer Belt
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire FRQE7000LW Manual Pages
Wiring Diagram (All Languages) - Page 1
... of the code and the START indicator light will appear in moisture sensor bar circuit or dirty bars. If problem persists, replace electronic control. If problem persists, replace electronic control. Remove wires from dryer. Example E24: The four indicator lights would be cleared when mode is within 50 K (± 10%), check wiring between incoming...
Wiring Diagram (All Languages) - Page 2
...When the DRYNESS button is displayed. 3 turns: Drive motor runs; When the START button is lit. e. Dryer will make the DAMP LED come on. 4 turns: Drive motor runs;
heat source is off . Drying ...TEMP LED's should be used to select the following tests:
Rotate the program knob clockwise from dryer. If the Temp selector is the rotary knob, and the knob is pressed, all LED'S...
Installation Instructions (All Languages) - Page 1
All about the
Installation
of your Dryer
TABLE OF CONTENTS
Important Safety Instructions 2-3 Reversing Door 18-19 Installation Requirements 4-10 Accessories 20 Installed Dryer Dimensions 11 Español 21 Installation Instructions 12-17
137371800A (1006)
Installation Instructions (All Languages) - Page 2
...-resistant thread tape (for future reference. RISK OF FIRE
Read all of all occupants. • Immediately call the fire department. Cartons covered with flexible plastic venting material. This dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - Follow the gas supplier's instructions.
• If you cannot reach your building...
Installation Instructions (All Languages) - Page 3
...tight on terminal block
‰ Approved strain relief installed ‰ Terminal access cover installed before using this dryer.
WARNING
WARNING indicates a potentially hazardous situation which , if not avoided, ...injury.
check with soapy water, NEVER check with flame
240v Electric Supply (Electric Dryer)
‰ Approved NEMA 10-30R or 14-30R service cord with a WARNING or ...
Installation Instructions (All Languages) - Page 4
... Canada have factoryinstalled, 4-wire power supply cord (NEMA 14-30R).
4 INSTALLATION REQUIREMENTS
Í NOTE
Because of potentially inconsistent voltage capabilities, the use of this dryer with clothes dryers. Individual 30 amp. OUTLET RECEPTACLE - For 4-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM.
4-WIRE POWER SUPPLY CORD KIT (not supplied)
4-wire...
Installation Instructions (All Languages) - Page 5
.... The tubing MUST be isolated from the gas supply piping system during any circumstances, cut, remove, or bypass the grounding prong.
Use ONLY black iron, stainless steel, or plastic-coated brass...requirements
WARNING
EXPLOSION HAZARD Uncoated copper tubing will corrode when subjected to the dryer.
6 The dryer MUST be disconnected from the gas supply piping system during any pressure ...
Installation Instructions (All Languages) - Page 6
... or metal foil duct, replace it with flexible plastic or metal foil venting materials.
When the dryer stops, the dampers automatically close to installing dryer duct. The following are...can create excessive drying times and fire hazards. These conditions will obstruct clothes dryer airflow and increase the risk of insects and rodents. INSTALLATION REQUIREMENTS
Exhaust ...
Installation Instructions (All Languages) - Page 7
...If the dryer is not ...increasing drying times. A clothes dryer produces combustible lint. The dryer must be installed downstream with ..., continued
WARNING
FIRE HAZARD A clothes dryer must be expelled into the duct to...inspect the outdoor exhaust opening and remove any accumulation of lint around the... all joints with exhaust system.
The dryer MUST NOT be exhausted into a chimney, a ...
Installation Instructions (All Languages) - Page 8
...months with short, straight adapter and 90°
elbow allows for proper operation. Dryer vent elbows are available through a roof may cause condensation and faster accumulation of ...can be accomplished by installing a quick-turn elbow required to meet minimum installation depth of free-standing dryer: • Straight back venting allows for 0" (0 cm) installation. • Venting right with ...
Installation Instructions (All Languages) - Page 9
... flow of 18 inches (45.7 cm) above the floor. IMPORTANT
DO NOT INSTALL YOUR DRYER: 1 In an area exposed to dripping water or outside (outdoors, not beneath the mobile home) using ... Metal ducting must be made for outside make up air. Rigid metal duct is preferred.
3 If dryer is exhausted through the floor and area beneath the mobile home is enclosed, the exhaust
system MUST...
Installation Instructions (All Languages) - Page 10
... in a bedroom, bathroom, recess or closet, MUST be exhausted outdoors.
2 No other fuel burning appliance shall be installed in the same closet as the gas dryer.
3 Your dryer needs the space around it for the full length of the door, is required.
Openings are required to achieve 0" (0 cm) rear installation.
0" (0cm)
0" (0cm...
Installation Instructions (All Languages) - Page 11
... supply on rear of unit
centerline height for rear vent
39" (99cm)
* To obtain these minimal depth dimensions, dryer must be vented straight back. Upward venting of exhaust on pedestal-mounted or freestanding dryer adds approximately 4 in . (2 cm) to installation depth. Using a quick-turn 90° elbow (right or down on freestanding...
Installation Instructions (All Languages) - Page 13
.... Grounding type wall receptacle
Do not, under any circumstances, cut, remove, or bypass the grounding prong. Electric dryer (Canada)
WARNING
ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding ...ordinances. In the event of electrical shock. For a grounded, cord-connected dryer: 1 The dryer MUST be plugged into an appropriate outlet that is properly installed and grounded...
Installation Instructions (All Languages) - Page 14
...
The supply line must be equipped with an approved manual shutoff valve. INSTALLATION INSTRUCTIONS
Gas connection
1 Remove the shipping cap from gas supply
4 Check for gas system leaks with a manometer. IMPORTANT
DO NOT connect the dryer to 0.96 cm) reducer for gas leaks with an open flame.
14 gas service without...
Installation Instructions (All Languages) - Page 15
... source before servicing could result in personal injury or even death.
1 Turn off power supply to outlet. 2 Remove the screw securing the terminal block
access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power...
Installation Instructions (All Languages) - Page 16
... personal injury or even death.
1 Turn off power supply to outlet. 2 Remove the screw securing the terminal block
access cover in the lower corner on the terminal block.
power cord, NEMA 14-30 ...and BLACK power cord conductors to the outer, BRASS colored terminals on the back of the dryer. 3 Install a UL-approved strain relief according to the center, SILVER colored terminal on the terminal ...
Installation Instructions (All Languages) - Page 17
Place a level on the power at the circuit breaker/fuse box. 5 Read the Use & Care Guide provided with 3-prong grounded plug
17 Remove and discard door tape.
The dryer MUST be level and resting solidly on all four legs.
Use of a 4" (102 mm) clamp (item A) is off at a circuit breaker/fuse box before...
Installation Instructions (All Languages) - Page 20
... White Pedestal - P/N CFPWD15B A storage pedestal accessory, specifically designed for stacking this dryer may order one . If your Use and Care Guide for use in a location supplied with...(or approved by) the manufacturer could result in the initial purchase of your dryer. Replacement parts:
If replacements parts are needed for your washer, contact the source where you purchased your ...
Product Specifications Sheet (English) - Page 2
... Door Open 90˚ Pedestal Dimensions A - Accessories information available on the web at frigidaire.com
Specifications subject to change. Printed in the U.S.A. Electric/Gas Dryer
Frigidaire Next Level
Front Load Dryer
FRQE7000L W 7.0 Cu. Front Load Laundry -
B
C
A
B
C
A
NOTE: For planning purposes only. Ft. Product Dimensions A - Height (Single) Height (Stacked) B - Width...
Similar Questions
How To Replace Frigidaire Gleq2152es0 Dryer Belt
(Posted by lovelDainj 10 years ago)
Dryer Belt
I had to take apart my dryer to replace the heating coil, while taking out the drum a pullie inside ...
I had to take apart my dryer to replace the heating coil, while taking out the drum a pullie inside ...
(Posted by jennamead 10 years ago)
How To Remove Air Duct Cover (lint Filter Holder) From Frqe 7000lw0
(Posted by goomaster4 11 years ago)
The Dryer Will Not Start, No Lights, But The Light Inside Is On When Door Is Ope
(Posted by dboland27 11 years ago)
Error Code 62
Started dryer...ran for about 20 minutes...then flashed error code 62 and stopped working
Started dryer...ran for about 20 minutes...then flashed error code 62 and stopped working
(Posted by LKHudd 12 years ago)