Fluke 83V Support Question
Fluke 83V Support Question
Find answers below for this question about Fluke 83V.Need a Fluke 83V manual? We have 2 online manuals for this item!
Question posted by brucezibung on August 3rd, 2015
Invalid Eeprom Data Message. Can It Be Remedied Without Sending It To A Repair
can the fluke 83 series V be reset to clear the eeprom err message without sending it to a repair facility?
Current Answers
Answer #1: Posted by TommyKervz on August 3rd, 2015 9:04 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,823
Member since:
January 10th, 2013 Points: 17,776,823
Invalid EEPROM data. Have Meter serviced as the only option' recommended by Fluke.
Related Fluke 83V Manual Pages
FE 83V & 87V Users Manual - Page 1
Users Manual
®
80 Series V
Multimeters
May 2004 Rev. 1, 8/04 2004 Fluke Corporation, All rights reserved. All product names are trademarks of their respective companies.
FE 83V & 87V Users Manual - Page 2
... for its option, repair at no charge, replace or refund the purchase price of a defective product purchased through a Fluke authorized sales outlet and at the applicable international price. THIS WARRANTY IS YOUR ONLY REMEDY. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM...
FE 83V & 87V Users Manual - Page 3
Table of Contents
Title
Page
Introduction...1 Contacting Fluke ...1 Safety Information ...2 The Meter's Features ...6
Power-Up Options ...13 Automatic Power-Off ...13 Input Alert Feature ...13 Making Measurements...13 Measuring AC and DC ...
FE 83V & 87V Users Manual - Page 4
80 Series V
Users Manual
Measuring AC or DC Current 24 Measuring Frequency 27 Measuring Duty Cycle 29 Determining Pulse Width 30 Bar Graph...30 Zoom Mode (Power ...
FE 83V & 87V Users Manual - Page 5
... Levels 50 18. Functions and Trigger Levels for Frequency Measurements 28 7. Model 87 AC Voltage Function Specifications 44 11. Frequency Counter Specifications 49 17. Model 83 AC Voltage Function Specifications 45 12. MIN MAX Functions...33 8. MIN MAX Recording Specifications 52
iii Pushbuttons...8 5. Temperature Specifications (87 Only 47 14. Current Function...
FE 83V & 87V Users Manual - Page 6
80 Series V
Users Manual
iv
FE 83V & 87V Users Manual - Page 9
... 87 appears in this manual apply to Series V Models 83 and 87 multimeters (hereafter referred to as "the Meter"). To register your product, visit register.fluke.com
1 Introduction
Contacting Fluke
To contact Fluke, call one of the following telephone numbers:
USA: 1-888-44-FLUKE (1-888-443-5853) Canada: 1-800-36-FLUKE (1-800-363-5853) Europe: +31 402...
FE 83V & 87V Users Manual - Page 10
80 Series V Users Manual
Safety Information
The Meter complies with:
• EN61010-1:2001 • ANSI/ISA S82.01-2004 • CAN/CSA C22.2 No. 1010.1:2004 • ...
FE 83V & 87V Users Manual - Page 11
... current, turn off circuit
power before you use the Meter if it operates abnormally. Then select the filter function.
3 Remember to place the Meter in series with voltages above 30 V ac rms, 42 V ac peak, or 60 V dc. When in doubt, have the Meter serviced.
• Do not operate the Meter...
FE 83V & 87V Users Manual - Page 12
80 Series V Users Manual
WCaution To avoid possible damage to the Meter or to the equipment under test, follow these guidelines:
• Disconnect circuit power and discharge ...
FE 83V & 87V Users Manual - Page 14
80 Series V Users Manual
The Meter's Features
Tables 2 through 5 briefly describe the Meter's features. Return terminal for voltage, continuity, resistance, diode, capacitance, frequency, temperature (87), and duty ...
FE 83V & 87V Users Manual - Page 16
..." until C is released. Enables the Meter's smoothing feature. To return to autoranging, hold for 1 second) Enables the Meter's calibration mode and prompts for a password. 80 Series V Users Manual
Button
A
(Yellow)
B C
Table 4. The Meter reads "CAL" and enters calibration mode. Cancels MIN MAX (hold the button down for the selected function. Pushbuttons...
FE 83V & 87V Users Manual - Page 18
80 Series V Users Manual
Button
F
(Relative mode)
G
Table 4.
Enables the Meter's high impedance mode when the mV dc function is subtracted from all subsequent readings.
Power-up ...
FE 83V & 87V Users Manual - Page 20
...Err CAL Err LEAd
Feature
0L
Indication
The number of segments is on the capacitor being used. In normal operation 0 (zero) is relative to the terminal being tested. The bar graph also has a zoom function, as described under "Zoom Mode".
Invalid EEPROM data. Have Meter serviced. Invalid calibration data...left . Error Messages Replace the ...Series V Users Manual
Table 5.
FE 83V & 87V Users Manual - Page 22
... voltage range equal to or higher than the ac range. This procedure improves the accuracy of an ac voltage, measure the ac voltage first. 80 Series V Users Manual When measuring voltage, the Meter acts approximately like a 10 MΩ (10,000,000 Ω) impedance in high-impedance circuits.
FE 83V & 87V Users Manual - Page 24
... also reads OL. The continuity function detects intermittent opens and shorts lasting as little as shown in Figure 4. To measure temperature, do the following:
1. 80 Series V Users Manual
Measuring Temperature (87)
The Meter measures the temperature of these ranges show OL on or off.
The continuity test features a beeper that range...
FE 83V & 87V Users Manual - Page 26
...resistance ranges are some tips for measuring resistance:
• The measured value of a resistor in Figure 5. 80 Series V Users Manual
Measuring Resistance
WCaution To avoid possible damage to the Meter or to the equipment under test, ...voltage capacitors before measuring resistance.
The Meter measures resistance by sending a small current through all possible paths between the probes.
FE 83V & 87V Users Manual - Page 30
...V. A continuous beep sounds if the reading is open.
22 This function tests a semiconductor junction by sending a current through the junction, then measuring the junction's voltage drop. In a circuit, a good ...however, the reverse-bias reading can vary depending on the component's negative terminal. 80 Series V Users Manual
Testing Diodes
WCaution To avoid possible damage to the Meter or to ...
FE 83V & 87V Users Manual - Page 37
... up the Meter to the AVG (average) display.
+Slope Trigger Point
30% Above +Slope
-Slope Trigger Point
70% Below -Slope
100%
Figure 9. Systems such as electronic fuel injection systems and switching power supplies are controlled by pulses of varying width, which can be checked by pressing E. Measuring Duty Cycle
Duty cycle...
FE 83V & 87V Users Manual - Page 43
... in Table 8.
35 Maintenance
XWWarning
To avoid possible electric shock or personal injury, repairs or servicing not covered in this manual should be replaced. Shake out any input... signals before measuring current, test the appropriate fuse as described in the 80 Series V Service Information. General Maintenance
Periodically wipe the case with a cleaning and oiling agent (...
Similar Questions
Cal Err Message Is Showing While On The Clamp Meter
CAL Err message is showing while power on the clamp meter.No buttons are functioning after this erro...
CAL Err message is showing while power on the clamp meter.No buttons are functioning after this erro...
(Posted by kvramesh 1 year ago)
I Get A 'do9' Message Flash When I Turn Off The Meter.
The message flashes until it dies. It is a detachable face meter so I switched the faces and the new...
The message flashes until it dies. It is a detachable face meter so I switched the faces and the new...
(Posted by RAErickson 3 years ago)
787 Uncal Message Reset.
how can I reset the unca l error message on my 787 without going thru a complete calibration?
how can I reset the unca l error message on my 787 without going thru a complete calibration?
(Posted by Dludwig421 6 years ago)
Meaning Of Error Message [ 511]
hi, I'm discovering the fluke 8845A multimeter, i try to connect the usb/serial cable provided with ...
hi, I'm discovering the fluke 8845A multimeter, i try to connect the usb/serial cable provided with ...
(Posted by khaoula 6 years ago)
Battery Warning Message
Battery warning message comes on whenever continuity buzzer is activated. Battery is fully charged a...
Battery warning message comes on whenever continuity buzzer is activated. Battery is fully charged a...
(Posted by Johnkola00 8 years ago)