Fluke 287 Support Question
Fluke 287 Support Question
Find answers below for this question about Fluke 287.Need a Fluke 287 manual? We have 2 online manuals for this item!
Question posted by sodefunsho on August 7th, 2020
I Need The Calibration Procedure For Fluke 287
The person who posted this question about this Fluke product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by INIMITABLE on August 7th, 2020 3:49 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,069,620
Member since:
April 3rd, 2020 Points: 2,069,620
HOW TO CALIBRATE A FLUKE MULTIMETER
Hold the Min/Max button down while turning the rotary know to the "VAC" position. ...
Press the Auto/Hold button again. ...
When "C-01" displays on the screen, attach the outputs from the meter to the inputs on your electric calibrator.
Get more information procedures in its calibration procedure manual here https://pdf4pro.com/file/73573/manuals_287_289_cmeng0000.pdf.pdf&ved=2ahUKEwjZ8Iyl84jrAhWLz4UKHSm1AKoQFjAAegQIBRAB&usg=AOvVaw1L7HmE_r48MOvcoReaFxaZ
Or get a visual explanation here
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Fluke 287 Manual Pages
Fluke 287 and 289 Multimeter Users Manual - Page 1
Specifications subject to change without notice.
Users Manual All product names are trademarks of their respective companies. All rights reserved. ®
287/289
True-rms Digital Multimeters
June 2007, Rev. 1, 7/08
© 2007, 2008 Fluke Corporation.
Fluke 287 and 289 Multimeter Users Manual - Page 4
287/289
Users Manual
Controlling Meter Power 12 Powering the Meter On and Off Manually 12 Battery Level Indicator 12 Automatic Power-Off 12 Battery Saver ...
Fluke 287 and 289 Multimeter Users Manual - Page 6
287/289
Users Manual
Error Messages ...56 Maintenance ...57
General Maintenance 57 Testing the Fuses...57 Replacing the Batteries 59 Replacing the Fuses 59 Test Lead ...
Fluke 287 and 289 Multimeter Users Manual - Page 8
287/289
Users Manual
vi
Fluke 287 and 289 Multimeter Users Manual - Page 10
... Width Measurements 46 28. Current Measurement Circuit Connection 41 23. Current Measurement Setup 40 22. Duty Cycle Measurements ...44 26. Test Lead Storage ...59 30. 287/289
Users Manual
18. Duty Cycle Display ...45 27. Frequency Display ...43 25. Capacitance Measurement 35 20. Conductance Measurement 34 19.
Fluke 287 and 289 Multimeter Users Manual - Page 11
...
Pay particular attention to as specified in the world: +1-425-446-5500 Visit Fluke's web site at: www.fluke.com
Register your Meter at: http://register.fluke.com
Safety Information
The Meter complies with:
• ANSI/ISA 82.02.01... using this manual apply to the model 289 and model 287 True-rms Digital Multimeters (hereafter referred to the insulation surrounding the connectors.
1
Fluke 287 and 289 Multimeter Users Manual - Page 12
287/289 Users Manual
• Make sure the battery door is indicated may be present. Replace damaged test leads before connecting the live test lead before ...
Fluke 287 and 289 Multimeter Users Manual - Page 14
N10140
Conforms to relevant Canadian and US standards
Conforms to Fluke's website for recycling information.
4
Go to relevant Australian standards
Underwriters Laboratory listed product
s
Inspected and licensed by TÜV Product Services
IEC Measurement Category III - 287/289 Users Manual
Symbols
Table 1 lists and describes the symbols used on the display)
J
Earth ground
...
Fluke 287 and 289 Multimeter Users Manual - Page 18
... display.
P Secondary display Displays secondary measurement information about the input signal.
8
Bar Graph
The analog bar graph functions like Crest Factor. An input of measure.
287/289 Users Manual
Table 3. K Date
Indicates the date set in the internal clock. The bar graph is enabled (not associated with the continuity beeper).
Fluke 287 and 289 Multimeter Users Manual - Page 36
... not displayed while the Meter is used for both ac and dc signal components (voltage or current) as needed.
AC over DC
8:10pm
06/13/07
DC over ac (DC,AC), and ac combined with dc ... autoranging is capable of these three displays using the ac+dc modes. Down-ranging occurs
26 287/289 Users Manual
Measuring AC and DC Signals
The Meter is available when using the Function and...
Fluke 287 and 289 Multimeter Users Manual - Page 48
... current is the flow of the break. Touch the red probe to the more negative side of electrons through a conductor. Be sure to note the measurement unit given at the right side of the ...dc current, proceed as follows:
1. voltage capacitors.
38
2. Turn off power to the circuit. 287/289 Users Manual
Measuring Current
XW Warning
To avoid damage to the Meter and possible injury, never ...
Fluke 287 and 289 Multimeter Users Manual - Page 59
...Naming Saved Data" section later in this information has been loaded into the Meter from Fluke's support web page using the Software Update option. The displayed data is used to...Info selection lists the serial number, model number, firmware version, calibration date, and calibration counter. See the 287/289 Calibration Information document to the menu item labeled Smoothing.
True-rms Digital...
Fluke 287 and 289 Multimeter Users Manual - Page 66
... lead in either A or mA/μA jack. Leads in corresponding A/mA or μA position.
287/289 Users Manual
Error Messages
Table 10 list some of the error messages the Meter may display and the...date and time were lost.
The Meter will turn
now. Table 10.
Error: Date and Time need to measure current but rotary switch not in both A and mA/μA jacks. No Thermocouple connected...
Fluke 287 and 289 Multimeter Users Manual - Page 67
... be performed only by qualified personnel as follows:
1. Clean the terminals as described in the 287/289 Service Information. Turn the Meter off and remove all test leads.
2. Shake out any...voltage, and speed ratings shown in the Meter's display. To prevent damage or injury, install only Fluke specified replacement fuses with the Meter in the S function, insert
a test lead into the amps ...
Fluke 287 and 289 Multimeter Users Manual - Page 71
... this manual to the location provided by the appropriate Fluke contact. If damage is detected, contact Fluke. If the Meter still does not work properly:
1. Check and replace (as needed) the batteries, fuses, and test leads.
4. A Meter under warranty will be repaired or replaced (at Fluke's option) and returned at no responsibility for damage...
Fluke 287 and 289 Multimeter Users Manual - Page 72
... Part/Model Number
1
2798434
1
2798418 (289) 2798429 (287)
1
2578234
1
2740185
1
2578178
5
2743764
1
2760673 (289) 2798407 (287)
1
2734828
3
2793516
1
2723772
1
2578283
1
2578252
1
2578265
62
To order parts and accessories, refer to the "Contacting Fluke" section. 287/289 Users Manual
Service and Parts
Replacement parts and accessories are shown in Tables 11 and 12...
Fluke 287 and 289 Multimeter Users Manual - Page 73
Replacement Parts (cont.)
Item
Description
Qty. Fluke Part/Model Number
13 RSOB Housing, Lower
1
2578290
14 Case Bottom
1
2578184
...TL71
24 Alligator Clips, one black and one red
2
1670652 (Black) 1670641 (Red)
25 Manual, Manual Pack, Fluke 287/289
1
2748851
26
287/289 Users Manual CD [1]
1
2748872
WTo ensure safety, use exact replacement only.
[1] The Users and Getting Started...
Fluke 287 and 289 Multimeter Users Manual - Page 76
287/289 Users Manual
General Specifications
Maximum voltage between any Terminal and Earth Ground: 1000 V W Fuse Protection for mA or μA inputs 0.44 A (44/100 A, 440 mA), 1000 V FAST Fuse, Fluke specified part only W Fuse Protection for A input 11 A, 1000 V FAST Fuse, Fluke specified part only Battery Type 6 AA Alkaline batteries, NEDA 15A IEC...
Fluke 287 Datasheet - Page 1
...logged read-
button. lead resistance from low ohms or capacitance measurements
• New -
enables you no longer need to download logged readings to a PC to remove test
TrendCapture displays vDC logged date. New Fluke 287
True-rms Electronics Logging Multimeter with TrendCapture
Technical Data
The advanced, logging digital multimeter with high accuracy and TrendCapture...
Fluke 287 Datasheet - Page 2
...75 in x 4.03 in x 2.38 in) Weight: 870.9 g (28 oz)
2 Fluke Corporation 287 True-rms Electronic Logging Multimeter with TrendCapture
Basic Accuracy 0.025 %
0.4 % (true-rms) 0.15 %
0.7 % (true-rms) 1.0 %
0.05 %
1.0 %
0.005 %
Ordering information
287 True-rms Electronics Logging Multimeter with TrendCapture
Optional accessories FVF-SC2 FlukeView® Forms
Software with Cable 80BK Integrated DMM...
Similar Questions
Calibration Adjustment Procedure For Fluke 355 Clamp Meter
clamp meter readings out specification we need to know how to minimize the error
clamp meter readings out specification we need to know how to minimize the error
(Posted by bennykittoop 8 years ago)
Fluke 971 Thermohygrometer Calibration
I am from Malaysia and looking for any local vendor in Malaysia that can carry out calibration follo...
I am from Malaysia and looking for any local vendor in Malaysia that can carry out calibration follo...
(Posted by kalairajamanickam 9 years ago)
Fluke 971 Calibration
Do we have any local company that can do calibration follow the fluke 971 spec
Do we have any local company that can do calibration follow the fluke 971 spec
(Posted by kalairajamanickam 9 years ago)
Procedure For Removing And Replacing A Battery Pac For 199c Scope Meter
(Posted by herbertwillett 9 years ago)