Epson U220B Support Question
Epson U220B Support Question
Find answers below for this question about Epson U220B - TM Two-color Dot-matrix Printer.Need a Epson U220B manual? We have 2 online manuals for this item!
Question posted by yohannesmengistu1 on January 4th, 2023
Asking For U220b Dip Switch Settings For Epson Tm Two Color Dot Matrx
Can you please tell which switches to turn on and which to turn off?
Current Answers
Answer #1: Posted by SonuKumar on January 4th, 2023 9:13 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,620,300
Member since:
May 9th, 2021 Points: 16,620,300
This may vary from older U220s to newer ones, so results may vary.
Turn the printer over and remove the screw holding the protection plate over the dip switchs
Locate the 2nd bank of dip switches
Set switch 2-4 to ON
You can then self-test the printer to see if the Serial interface has been changed. If the interface still says "Serial", set 2-4 to OFF and set 2-8 to ON. ...
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Epson U220B Manual Pages
Technical Reference - Page 3
... Command System EPSON took the initiative by introducing ESC/POS, a proprietary POS printer command system ...DIP switch setting. TRADEMARKS EPSON® and ESC/POS® are subject to change without the prior written permission of Seiko Epson Corporation.
❏ The contents of Microsoft Corporation. Add wall hanging unit and miscellaneous.
B Rev. Compatible with high scalability. TM...
Technical Reference - Page 4
...TM-U210/TM-U300.
Describes the external dimensions and specifications of the TM-U210/TM-U300."
Contains introduction of the Manual
This manual was created to provide information on the TM-U220 printer...notices and comparison information for using the TM-U220 as DIP switches, memory switches, error processing for replacing TM-U210/ TM-U300 with the WH-10." Comparison ...
Technical Reference - Page 12
...Notes for DIP switch 2-1 3-19 3.4.3 Memory Switches 3-19 3.4.4 Memory Switch Setup Mode 3-21 3.4.4.1 Starting the memory switch setup mode 3-22 3.4.4.2 Ending memory switch setting mode 3-22 3.4.4.3 Operating procedure 3-23 3.4.5 Adjusting Roll paper width 3-26 3.4.6 Adjusting Position of Roll Paper Near End Detector 3-27 3.4.7 Select Autocutter action 3-28 3.4.8 Connecting the Printer to...
Technical Reference - Page 21
...supply: EPSON PS-180...DIP switch 1-2. D
General Information 1-5 excludes paper and ribbon)
Weight (mass)
Type A: Approximately 2.7 kg {5.94 lb} Type B: Approximately 2.5 kg {5.5 lb} Type D: Approximately 2.3 kg {5.06 lb}
*Multilingual means the printer...TM-U220 Technical Reference Guide
1.4 Product Specifications Overview
Print method Paper width Cut type
Character sets
serial impact dot matrix...
Technical Reference - Page 22
... and paper Specifications
Printing method:
Serial impact dot matrix
Head wire configuration:
9-pin serial configuration
Printing... mm {2.50" / 2.24" / 1.87"} Dot positions depend on DIP switch setting.
Kanji: 2 half dots (default) or 0 half dots. D See the table "Dot width of Kanji characters is the default)
*1 This printer adjusts print speed when it prints graphic data, etc...
Technical Reference - Page 23
...
40
33
17.8
40
36
30
16
35
32
27
14.5
33
30
25
13.3
*: The dot spacing between Kanji character is selected by an ESC/POS command.
D
General Information 1-7
TM-U220 Technical Reference Guide
The dot width of the printable area depends on DIP switch setting and paper width as shown in the following table.
Technical Reference - Page 33
TM-U220 Technical Reference Guide
1.7 External Dimensions and Mass 1.7.1 External Dimensions and Mass
Model type External Dimensions
Width
...
Approximately 2.5 kg
{Approximately 9.8"} {5.5 lb}
248 mm
Approximately 2.5 kg
{Approximately 9.8"} {5.1 lb}
(All the numeric values are typical.) Color:EPSON standard color (ECW, EDG) 1.7.1.1 Overview (Type A)
Rev. D
General Information 1-17
Technical Reference - Page 43
...Visual Basic, MSComm)
-
Rev.
Type B (*)
(*) When RTS/CTS control is connected to TM printer via a modular connector.
TM-U220 Technical Reference Guide
2.3.1 Stand alone
Both TM printer and customer display (DM-D) are connected to select Y-type connection, confirm that the DIP switch has been set "Y-type connection: Enable."
You need to use the UB-S09 interface when...
Technical Reference - Page 44
..., Visual C)
- D Note: On the DM-D (DM-D500 etc...) which has a DIP switch to select Y-type connection, confirm that the DIP switch has been set to the first printer via USB. (See "Changing the DIP Switch Settings" in Chapter 3 for DIP switch settings.)
2-8 System Planning
Rev. Type B
Type A or B
2.4 Parallel Connection
The TM printer is connected to the host PC via a serial port.
Type A or...
Technical Reference - Page 51
... various setting ( If you use driver) ("Install a Printer Driver in the Host PC / POS Terminal" (page 3-34))
5.
D
Setup 3-5
Driver set by the spacer & Memory switch setting.
• Roll Paper Near End Detector (For model equipped with the detector) ("Adjusting Position of preparing to set them.
•DIP switches ("Adjusting the DIP Switches" (page 3-15)) The DIP switches set serial...
Technical Reference - Page 61
... of DIP switches.
If you need to change settings, follow the steps below . Note: The functions of US is different for each interface model. Use a crosshead screwdriver to prevent an electric short, which can damage the printer.
The DIP switch function of the switches are "STD", use the "US" tables below to make your changes:
CAUTION:
Turn off...
Technical Reference - Page 63
.../35
Off 40/33
2 Reserved
Type A, B
(Auto cutter enable/ Fixed to Off
Rev. D
Setup 3-17 Regardless of the setting of DIP switch 1-1, if you want to Off DIP switch
Note: When the printer has a data receive error, the printer prints "?."
Type D Fixed to Off
Fixed to Off Not used Fixed to On
disable)
3 Reserved
-
4 Pin 31 reset...
Technical Reference - Page 65
...; Control from ESC/POS command
Some Memory switch settings can be changed by the "Memory switch setting mode."See "Memory Switch Setup Mode" on what can be changed ) • Control from Windows driver (Advanced Printer Driver only, and
there are able to set these items automatically.
Memory switch set which is turned off, the settings are stored in the following table...
Technical Reference - Page 67
... width" (page 3-26) also to "Memory switch." These settings can be set by "Memory switch setup mode." See "Memory Switch Setup Mode" on page 321.
3.4.4 Memory Switch Setup Mode
The following items are two methods, DIP switch and Memory switch, to follow the proper procedure, and turn the power off in the memory switch setup mode:
❏ Basic Serial communication condition...
Technical Reference - Page 85
... printer, you need to solve the your problem. The procedure depends on the "User's Manual" and "Status API Reference Manual" to adjust serial communication setting between printer and printer driver. This module (device driver) is not correct, please see the installation manual. Rev.
See "Adjusting the DIP Switches" (page 3-15) and "Memory Switches" (page 3-19) for the printer...
Technical Reference - Page 86
... Test
The self test lets you know if your printer is closed properly.
2. Make sure the printer is turned off and the roll paper cover is operating properly.... the control circuits, printer mechanisms, print quality, control software version, and DIP switch settings. The self test prints the printer settings and then prints the following :
*** completed ***
The printer is ready to pause...
Technical Reference - Page 93
... is slow.
TM-U220 Technical Reference Guide
4.5 Printer prints "?" To use the type D model, you turn on the hex dump function, the printer prints all commands and other errors, we recommend confirming the transmission setting of the following errors occurs during serial interface communication, the printer prints "?" or Incorrect Data With Serial Interface
If one of DIP switch...
Technical Reference - Page 119
...
This section informs you replace the TM-300 with 2 copies; The memory switch setting mode is for adjusingt the memory switches by printer only (No need for a host PC.) See "3.4.3 Memory Switches (3-19 page)" and "3.4.4 Memory Switch Setup Mode (3-21 page)" for detail.
6.2.8.4 Memory Switch and Memory Switch setting mode The TM-U220 has a memory switch ,which is TBD.)
6.2.8.2 NV bit-image...
User Manual - Page 9
... the DIP switches are at the beginning of this manual are subject to change without the prior written permission of the numbers. Neither Seiko Epson Corporation nor its affiliates shall be liable to the use of the information contained herein. Copyright © 2003 by any liability assumed for damages resulting from your printer;
See...
User Manual - Page 10
...product may lead to fire. Doing so may cause equipment damage and burning.
2 TM-U220 User's Manual
Connection to an improper power source may cause fire or electric shock...Seiko Epson service center for advice. Immediately unplug the equipment and contact your equipment immediately if it produces smoke, a strange odor, or unusual noise. Tampering with the cover open the DIP switch ...
Similar Questions
Epson Tm U 295 Slip Printer Not Avayilable How To Fix
(Posted by it19227 2 years ago)
Paper Feed Button Not Functioning
Hi Guys, I have 2 epson u220b Micros Pos order printers Idn specific that needs to be set up, but wh...
Hi Guys, I have 2 epson u220b Micros Pos order printers Idn specific that needs to be set up, but wh...
(Posted by microtech4u 9 years ago)
How To Print 40 Col. Printing
Inform The Dip Switch Settings To Print 40 Columns
Inform The Dip Switch Settings To Print 40 Columns
(Posted by trusalunke 10 years ago)
Default Switch Setting
Lq1070 Epson
(Posted by raviluhadia 11 years ago)
Dip Switch Settings
What are the dip switch settings for a serial board? U220B
What are the dip switch settings for a serial board? U220B
(Posted by barram2 11 years ago)