Home » Electrolux » Cooktops » Electrolux EW36CC55GS

Electrolux EW36CC55GS Support Question

Find answers below for this question about Electrolux EW36CC55GS.
Need a Electrolux EW36CC55GS manual? We have 4 online manuals for this item!

Electrolux Overview Questions Manuals Reviews Videos Research

Question posted by tcraig4 on January 15th, 2012

20a Fuse Blows On Filter Board. Replaced Filter Board. Same Problem.

Only happens when turning on induction elements. The 3 other burners work fine until I turn on induction burners. Then fuse blows and error code 95 appears. Then the entire stove doesn't function.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by OnlineOutreachSpecialist on January 17th, 2012 8:52 AM

OnlineOutreachSpecialist

Member since:
March 30th, 2011

Points: 2,848,320

60
points

E95 means : Mains voltage signal invalidly phase 1, undervoltage or optocoupler defective- this is an indication that one phase is wrong. The other phase will still work.

Technicians do the following:

Verify AC input voltage at the cooktop input. Verify AC main input cables, screws and jumpers. Verify the fuse resistance to be approximately 0 ohms on the Induction Module. Replace the Filter Board on the Induction Module.

You can tell this is not a DIY job, so please contact a professional.

Online Outreach Specialist

Related Electrolux EW36CC55GS Manual Pages

Complete Owner's Guide (English) - Page 1

Use & Care Guide Radiant/Induction Electric Cooktop 318 203 603 Rev. B (0802)

Complete Owner's Guide (English) - Page 3

... Maintenance 26 Cleaning Recommendations for the Ceramic Glass Cooktop 26-27 Care & Cleaning of Stainless Steel 27 Solutions to Common Problems 28-31 Entire Cooktop Does Not Operate 28 Cooktop Turns Off While Cooking 28 Surface Element Does Not Heat 28 Cooking Zone Does Not Heat Food (Induction Elements 29 Surface Element Too Hot or Not Hot Enough ....... 29 Food...

Complete Owner's Guide (English) - Page 5

...time to the appliance at the circuit breaker or fuse box in Canada, and local code requirements. During and after use your dealer to the cooktop. Smother the fire with a pan lid, or... authorized repair service. Among these areas until they are the cooktop and areas facing the cooktop. ! Do not repair or replace any other flammable materials contact hot surfaces. • Do ...

Complete Owner's Guide (English) - Page 6

...error message will be kept clean. Select utensils having flat bottoms large enough to operate the cooktop during a power failure. Do not let the pot holders touch hot surface units. Exhaust fan ventilation hoods and grease filters should be cleaned frequently, so the grease from steam. Proper relationship of utensil to element..., always turn fan on hood or filter. Greasy deposits...

Complete Owner's Guide (English) - Page 10

... POWER lock warm - The surface elements are all factors that will affect the amount of the element outline on the 36" cooktop as follows: - 1 small radiant elements located at the center rear position; - 2 dual radiant elements located at the left front position; - 1 small induction element located at the right rear position; - 1 dual induction element located at the right front...

Complete Owner's Guide (English) - Page 12

... Warm function. LOCKOUT FEATURE (- -) (See controls lock on page 11) - Fig. 9 Fig. 10 As the temperature rises, the element will...Cooktop Lockout feature is still too hot to OFF, the cooktop will cycle ON and OFF. The ON/OFF key pad for the desired cooking zone must be turned ON again for more precise settings at the HI setting. LH (Low Heat) should appear in each radiant element...

Complete Owner's Guide (English) - Page 15

... & straight sides. Min. Before Using the Cooktop 15 COOKWARE RECOMMENDATIONS INCORRECT CORRECT - size •...cooktop trim or does not rest completely on the cooktop surface. • Pan rests completely on Cooking Zone surface. • Curved or warped pan bottoms or sides. Correct the problems before attempting to activate the cooktop. Fig. 1 PLEASE NOTE THAT ON THE INDUCTION...

Complete Owner's Guide (English) - Page 20

... simmering. 20 Setting Surface Controls OPERATING THE INDUCTION COOKING ZONES - lo hi + Fig. 1 The cooktop has two induction Cooking Zones designed for a few seconds or... pad is reached). To Turn ON one or more information about the available Cooktop Zones power levels available see...sure to a boil and pan broiling. Any problems must be corrected before proceeding. 2. For ...

Complete Owner's Guide (English) - Page 22

.... This will keep track of the Cooking Elements. The Cooking Zone will display LH (Low Heat) for radiant elements and L for induction element indicating that the Cooking Zone is set time... control from being turned ON. timer 2. To Turn ON the Controls Lock Feature: Touch and hold the key pad. The Cooking Elements or any Cooking Element or Cooktop functions from beeping, touch...

Complete Owner's Guide (English) - Page 25

... off the shaft. Using a soft cloth, clean with a soft cloth. Do not use harsh scrubbing cleaners. To remove control knobs, turn to Clean Use hot, soapy water and a cloth. To replace knobs after cleaning, line up the flat sides of water on the control panel - then push the knob into place. Do...

Complete Owner's Guide (English) - Page 26

.... CAUTION Before cleaning the cooktop, be sure the controls are turned to the cooktop. Do not use the pad you use . - If soils remain, carefully scrape soils with cooktop cleaning cream and buff surface... pad, applying pressure as a cutting board or work surface in most hardware stores. lo ON OFF hi + - lo hi + Fig. 1 Prior to clean the cooktop for any other purpose. Clean and...

Complete Owner's Guide (English) - Page 27

...turning the surface elements OFF, use abrasive cleaners and scouring pads, such as they may occur if not removed immediately. Allow the cooktop to boil dry, not only will damage the cooktop...the ceramic glass surface, permanently damaging the cooktop surface. Special Caution for maintaining the appearance of the cooktop surface) may etch or discolor the cooktop. • Do not use an ...

Complete Owner's Guide (English) - Page 28

... breaker or replace fuse. Be sure to be sure. Check house lights to use for the element needed. This list includes common experiences that are locked. Set the cooktop controls to a slightly higher setting until element comes on controls area of cooktop. Turn control to unlock the Cooktop (see page 23 for service, review the following problems first. Contact...

Complete Owner's Guide (English) - Page 29

... may burn easily. Solutions to Common Problems 29 COOKING ZONE DOES NOT HEAT FOOD (INDUCTION ELEMENTS) • No cookware was placed on cooktop surface. • No power to the...medium or heavyweight cookware. Check steps under "Entire cooktop does not operate" in poor condition. • Cookware is properly connected to fit element. • Incorrect control setting. Use heavier...

Complete Owner's Guide (English) - Page 30

Try turning electrical power supply OFF and back ON to cooktop in this Owner's Guide. Do not slide metal utensils on to Common Problems COOKTOP ZONE CONTROL DISPLAYS E AND 2 DIGITS LED MAIN CONTROL DISPLAYS • Induction Cooktop main control has detected a fault or error condition. Test with rough bottom has been used . See Ceramic-Glass Cooktop section in order...

Complete Owner's Guide (English) - Page 31

... Care & Cleaning. • Cleaning materials not recommended for ceramic-glass cooktop have cooked onto surface. Use razor blade scraper to Common Problems 31 BROWN STREAKS AND SPECKS ON CERAMIC GLASS COOKTOP SURFACE • Boilovers have been used. AREAS OF DISCOLORATION ON CERAMIC GLASS COOKTOP SURFACE • Mineral deposits from water and food. Wipe remaining...

Complete Owner's Guide (English) - Page 32

... in accordance with original serial numbers that prove to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or other cosmetic parts.... one year from your original date of purchase, Electrolux will provide a replacement glass cooktop or radiant surface element for your appliance which are subject to be required. Products with the ...

Installation Instructions (All Languages) - Page 4

... serial plate on both sides of the line (timedelay fuse or circuit breaker is installed and grounded properly by a qualified installer or service technician. • These cooktops must be electrically grounded in accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No. 70-latest edition in serious injury...

Product Specifications Sheet (English) - Page 1

.../ or national electric codes. Cookware Compatibility Electrolux induction hybrid cooktops include a combination of electric elements that are compatible with all cookware, and induction elements that are compatible with ground. Wall Ovens Warmer Drawers Cooktops Built-In Ranges Induction Hybrid Cooktops EW36CC55G S, EW36CC55G W, EW36CC55G B 10" and 6" Induction Elements Boil water in 90...

Product Specifications Sheet (English) - Page 2

Induction Hybrid Cooktops EW36CC55G S, EW36CC55G W, EW36CC55G B 13" max. for 18" min. for 36" unprotected cabinet 24" min. or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz, fused on either side of unit. • It is protected by not less than 1/8" flame-retardant millboard covered with ground. • Connected Load (kW Rating) @ 240 / ...