Dewalt DXPW3835 Support Question

Find answers below for this question about Dewalt DXPW3835.
Need a Dewalt DXPW3835 manual? We have 1 online manual for this item!

Dewalt Overview Questions Manuals Reviews Videos Research

Question posted by amendi68 on May 29th, 2018

Excessive Oil Vapor

My DeWalt dxpw 3835 starts and when hose from valve cover to carburetor intake is removed there is excessive oil vapor from the crank case. When connected back it dies out.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Dewalt DXPW3835 Manual Pages

Instruction Manual - Page 2

...D Choke control M. Gas cap O. High-pressure hose Q. Nozzle holder C. Top handle Engine Refer to the engine instruction manual for pressure washers is not available, an SAE 30W non-detergent oil may be used. English DXPW3835 Pressure Washer A. Panel assembly B. K L M I . Quick-connect spray wand F. Frame G. If this oil is recommended, as these contain a rust inhibitor...

Instruction Manual - Page 3

... cannot see or smell. Read and follow all directions for each signal word. You could result in death or serious injury. English Specifications MODEL WEIGHT DXPW3835 125 lbs (56.7 kg) HEIGHT 28" (71.1 cm) WIDTH 24" (60.7 cm) Length 38" (96.5 cm) PSI** 3800 (26,200 kPa) GPM** 3.5 (13.2 L/min) Engine...

Instruction Manual - Page 4

... 1/2" (12.7 mm) be come ignited from fueling area before starting engine. • Heat will be used near children...chemicals known to the State of filler neck to allow it 's vapors can be low bottom of California to stop the product and...other reproductive harm. Do not overreach or stand on land covered with materials such as defined in section 4442, and maintained...

Instruction Manual - Page 5

...es, melt any material sensitive to heat (such as siding, plastic, rubber, vinyl or the pressure hose, itself), and damage live plants) that could be damaged from muffler exhaust heat. • Store fuel in an OSHA approved contain...

Instruction Manual - Page 6

...• Do not allow hose to contact muffler. • Never attach or remove wand or hose fittings while system ...is pressurized. • When using replacement lances or guns with this pressure washer, do not use a lance and/or lance/ gun combination that is leaking or damaged. • Never touch, grasp or attempt to cover...

Instruction Manual - Page 8

... it • Fuel or oil can result. Serious off valve, turn the valve to inju... injury. • The spray gun/wand is a powerful cleaning tool that could look like a toy to a child. • Reactive force ...• If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. the off valve, drain the fuel from leaks. ...

Instruction Manual - Page 11

...connection is preset at the factory. Remove the five colored quick- Add air in the nozzle holder (B) on the nozzle holder. Change to no more information). Place the nozzle holder (B) onto the panel assembly (A) and push each use the tire gauge to be cleaned. 2. Always check oil... high-pressure hose (P) to achieve optimum pres sure and cleaning.

Instruction Manual - Page 12

...hose with filter on wood 15˚ Yellow intense cleaning metal, concrete of small areas or wood 25˚ Green intense cleaning metal, concrete of larger areas or wood White Black 40˚ covers...(forward) before changing nozzles. 1. Press chemical hose (S) onto barbed fitting located near high pressure hose connection of causing damage to change nozzles while pressure washer is ...

Instruction Manual - Page 13

... to hoses from engine and equipment before starting engine. • Never run engine indoors or in injection injuries. Leaks caused by warranty. Never fill fuel tank when engine is running or hot. Wipe any fuel spillage from contact with any pets or animals. Wipe up Procedure 1. Check engine oil level. Starting Warning...

Instruction Manual - Page 14

... flow. Turn the water source on gun to remove all air from the hose. Depress trigger on to start after two pulls, squeeze trigger of water is present, turn the water source off. 4. Turn the engine ON/OFF switch (H) to the water source. Connect the water hose to the ON position. 11. Engage the trigger...

Instruction Manual - Page 15

... oil, change oil every 150 hours thereafter. CC 4. An oil designed specifically for proper storage procedures. Replace pump oil plug and tighten securely. 15 Place the fuel valve lever (M) in hose or...water source off while pressure washer engine is equipped with oil at the factory. Remove pump oil plug and fill with pump oil. Never turn water supply off . 5. Pull trigger on...

Instruction Manual - Page 16

...the following steps. Connect length of garden hose to hose as outlined in the following instructions: 1. Add RV antifreeze to water inlet of garden hose with water on ...Remove the high-pressure nozzle from the gun. Direct water supply into spray wand to relieve any obstructions with the nozzle cleaning tool (Y) provided and back flush with foreign materials, such as dirt, excessive...

Instruction Manual - Page 17

... down and the spray gun and wand in locating any other qualified service personnel. Accessories Recommended accessories for all water from damage. Remove garden hose from your tool, please contact the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue, Elk Grove Village, Il 60007, or call (877) FNA-GAS1. Caution...

Instruction Manual - Page 18

...of purchase. The manufacturer's warranty obligation is limited to , valves and seals, which are nontransferable. Frame (defects in material... wear of the appropriate warranty provisions. This warranty covers defects in material and workmanship and not parts failure... Pressure Pump (defects in material and workmanship) Includes nozzles, hoses, spray guns, wands Ninety (90) days from date of...

Instruction Manual - Page 19

...-connect spray wand: Allows the user to lower the temperature inside the pump. Water supply: All pressure washers must have a source of water. Chemical injection system: Mixes cleaners or cleaning solvents with the water. Choke control: Opens and closes carburetor choke valve. The unit of measure for the flow rate of water. Chemical hose...

Instruction Manual - Page 20

...on position. initial use. Engine ON/OFF switch in the No Choke position. Problem Code Engine will not start ...1, 2, 3, 4, 5, 6, 7, 8, 36 (refer to the engine's instruction manual for further engine troubleshooting...of normal use 22, 23, 24 Water leaking at gun/spray wand connection 25, 26 Water leaking at pump...25, 26, 27, 28 Oil leaking at pump...29, 30, 31, 32, 33, 34, 35 ...

Instruction Manual - Page 21

... the fuel valve lever to the No Choke pos ition. See Spray Wand Nozzles under 100 feet (30.48 m). Remove and clean filter. Turn off . Lengthen water supply hose instead of ...Spray wand not in chemical injector. 23 Worn or obstructed valves. 24 Worn unloader piston. 25 Worn or broken o-ring. 26 Loose hose connection. 27 Piston packings worn. When there is fully submerged into...

Instruction Manual - Page 22

... to engine instruction manual for correct amount. If problem persists, replace plug. Clean air filter element. Refer to remove any blockage. Drain and fill with oil. POSSIBLE SOLUTION Have replaced by authorized service center Tighten. Check and replace. English (Troubleshooting Codes cont.) Code possible cause 28 Pump head...

Instruction Manual - Page 68

The FNA Group 1825 Greenleaf Avenue, Elk Grove Village, IL 60007 (OCT11) Part No. 7104830 DXPW3835 Copyright © 2011 The following are trademarks the DeWALT Industrial Tool Co., used under license. the array of DeWALT Industrial Tools The FNA Group, 1825 Greenleaf Ave, Elk Grove Village, IL 60007, a licensee of pyramids on the surface of the...