Dewalt DXPW3400PR Support Question
Dewalt DXPW3400PR Support Question
Find answers below for this question about Dewalt DXPW3400PR.Need a Dewalt DXPW3400PR manual? We have 1 online manual for this item!
Question posted by Edeffef1990 on August 15th, 2022
Flow Sensor
flow sensor part isn't available.. what do I do?
Current Answers
Answer #1: Posted by SonuKumar on August 16th, 2022 8:24 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,638,180
Member since:
May 9th, 2021 Points: 16,638,180
https://www.allpartsinc.com/7113637-pressuready-pump-complete-with-flow-sensor.html
https://www.allpartsinc.com/dewalt-3400-psi-2-5-gpm-pressure-washer-dxpw3400pr.html
https://www.amazon.com/dewalt-pressure-washer-parts/s?k=dewalt+pressure+washer+parts
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Dewalt DXPW3400PR Manual Pages
Instruction Manual - Page 6
...kickback
and prevent hand or
arm injury.
• The spray gun/ wand is a powerful cleaning tool that could look like a toy to slip
a ladder.
Grip gun/wand firmly with missing or ... relieve
can kickback causing pump pressure.
Pull starter
serious hand and
cord slowly until water stops flowing.
• Use only accessories rated equal to or higher than the rating of this product....
Instruction Manual - Page 9
... not place the battery pack in checked baggage. Damaged battery packs should be put in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. Use Mode: ...battery pack may reach or exceed 104 °F (40 °C) (such as keys, coins, hand tools and the like. Electric shock may be kept away from materials that has received a sharp blow, been...
Instruction Manual - Page 10
... shipping cap, the pack will need to be considered 3 batteries at the end of this time or left . If shipping without the cap or in a tool, the pack will blink continuously indicating that the costs to recycle these batteries (or battery packs) at the Watt hour rating indicated next to "Use...
Instruction Manual - Page 11
... or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery pack has reached an appropriate temperature. You may impede air flow. Disconnect the charger from the power supply when there
9 A cold battery pack will charge at that is fully charged. c. The battery pack should be recharged...
Instruction Manual - Page 14
... basements, etc.
• Never operate unit in PRESSUREADY® system mode the engine and water flow will NOT be damaged. Wipe any pets, animals, or people. NOTICE: Use of fuels with a...• Remove battery before starting the engine. If pump is squeezed again the engine and water flow will to hoses from engine and equipment before starting engine, add the oil provided. Fig. See ...
Instruction Manual - Page 15
... the job to remove all air from the hose and flush any other battery will not start in PRESSUREREADY® system mode with low water flow.
WARNING: To reduce the possibility of water is in water inlet of property damage. Fig. O
14
7. To install battery pack: Insert battery pack 23 into...
Instruction Manual - Page 16
...10 seconds. When spray gun trigger is run without oil. After the engine has started , the water flow will illuminate. Refer to start. Damage to start after squeezing spray gun trigger. U
5. R
...squeeze the spray gun trigger to the engine will occur if the engine is released, water flow will
stop immediately and the engine will restart. S. Expect the spray gun/wand to verify...
Instruction Manual - Page 17
...valve will open and release a spray of unsafe operation. S) is moved forward to start water flow.
WARNING: Risk of water from the pump and high pressure hose by squeezing the spray gun... gun is present. P, AA, BB)
NOTICE: Risk of property damage. 6. Release trigger to stop water flow.
WARNING: Do not allow the unit to pump inlet. The valve will result. 1. Fig.
Connect ...
Instruction Manual - Page 18
... pressure washer without filter properly installed.
16 When the spray gun trigger is released, the water flow will pulsate and when operating in
hose or spray gun. 7. BB
4. To remove battery pack...to Storage for any and all water pressure before performing any obstructions with the nozzle cleaning tool 29 provided and back flush with the pump contact us at the factory. When performing ...
Instruction Manual - Page 19
.... 2.
To Prevent Fuel-Related Problems 1. Add Ethanol Shield™ fuel stabilizer following information available for more than 3 minutes. 5. When adding a gasoline stabilizer, fill the fuel tank .... Other products could be less than 30 days and/or when freezing temperatures are available for approximately 30 seconds or until protector fluid exits pump outlet. Unscrew bottle valve...
Instruction Manual - Page 20
... parts or accessories not obtained
from date of merchantability or fitness for a particular purpose and all parts said to be defective must be retained and available for rental purposes, damage resulting from date of purchase
Frame (defects in material and workmanship) AAATM - For all other concerns: To assure product SAFETY and...
Instruction Manual - Page 21
...
No or low pressure (after period of water in PRESSUREREADY® system mode with a low oil sensor. Troubleshooting Guide
This section provides a list of oil. Low or no oil. NOTE: This pressure washer... carburetor.
The unit of water. PSI*: Pounds per minute. The unit of measure for the flow rate of measure for water pressure.
Quick-connect spray wand: Allows the user to Spray Wand ...
Instruction Manual - Page 23
...filter element. If the fault code does not clear, remove and reinstall battery.
GREEN YELLOW
English
WATER FLOW
READY
FAULT
ON
OFF
RED
28
NO PROBLEM
A SYSTEM FAULT IS INDICATED
Green light ON = System ... and the red light will continue to flash in ON position Connect garden hose and turn water flow ON
Place the unit on a level surface
Fill fuel tank
Fill engine oil
Unit will not ...
Instruction Manual - Page 24
... fault: Replace the battery (5.4)
Unit is not on a level surface: (6.1)
Place on level surface
Unit is not on a level surface: (6.2)
Place on level surface
Water flow sensor fault: (7.1 + .2 .3 .4)
Take to authorized service center
Battery temperature too high: (5.2)
Outside temp too high, do not operate
Battery fault: Replace the battery (5.3)
The yellow light...
Instruction Manual - Page 84
... NOTE: The Bluetooth® word mark and logos are registered trademarks of the tool.
Nominal voltage is 20 or 60 volts. Other trademarks and trade names are trademarks for one or more DeWALT power... tools: the yellow and black color scheme, the "D" shaped air intake grill, the array of pyramids ...
Similar Questions
Piston Will Not Return To Rest Position. After Pushing Piston Back With Tool, I
after pushing piston back to starting position it will then fire single nail and remain in fired pos...
after pushing piston back to starting position it will then fire single nail and remain in fired pos...
(Posted by av8trr 6 months ago)
Flow Sensor Bypass
I have a DeWalt pressure sense DXPW3400PRthe flow sensor is giving me mixed readings and doesn't sta...
I have a DeWalt pressure sense DXPW3400PRthe flow sensor is giving me mixed readings and doesn't sta...
(Posted by davidjrsilva 2 years ago)
Dewalt 55168 Type 2
builds tp 20 psi and stops and continues running
builds tp 20 psi and stops and continues running
(Posted by elliottsandra57 3 years ago)
Bolt Size For Dewalt 734 Planner Tool Tray
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
(Posted by luklyd 8 years ago)
Is There Anywhere You Can Buy A Dewalt Mt16 Multi Tool Without Having To
buy it together with the MT8 as part of the DeWalt gift box set?
buy it together with the MT8 as part of the DeWalt gift box set?
(Posted by freginold 9 years ago)