Denon AVR 988 Support Question
Denon AVR 988 Support Question
Find answers below for this question about Denon AVR 988 - AV Receiver.Need a Denon AVR 988 manual? We have 11 online manuals for this item!
Question posted by Ktinjakarta on January 17th, 2021
How To Reset Demon 988 To Factory Setting?
it turns on for few seconds & flips off
Current Answers
Answer #1: Posted by waelsaidani1 on January 18th, 2021 10:06 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Turn off the power using the power button
Press POWER while simultaneously pressing <STANDARD> and <DSP SIMULATION>
Once the display starts flashing at intervals of about 1second, release the two buttons,
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
Related Denon AVR 988 Manual Pages
Literature/Product Sheet - Page 1
... a router or other network device to play music from your PC on your home audio system. To allow for easier browsing and playback of control your iPod via remote and... and JPEG for photos • Internet Radio You can access a list of purchasing a Denon product (amplifier, receiver, etc.) that already has network connectivity and you just want to wire-connect - New model information
ASD-3W ...
Audyssey MultEQxt Information - Page 1
...AV receivers today. There are centered at nearby frequencies. Parametric equalization relies on a few bands that MultEQxt is now available on parametric equalization. These filters can achieve optimum performance for every listener within the listening area to be the most advanced and sonically beneficial Auto Setup and Room Eq system... set the appropriate delays. What ...
Literature/Product Sheet - Page 1
...support • HDMI1.3a inputs/output that enhances your level of -Use
• Auto set-up to 1080p • 1080p video pass through • 12-bit/216-MHz video ... Discrete devices for ultimate HD video performance in low frequency band. New model information
AVR-988
AV Surround Receiver
A/V Surround Receiver featuring Dolby TrueHD, dts-HD Master Audio and HD Video that handle HD audio and...
Owners Manual - English - Page 1
AV SURROUND RECEIVER
AVR-988
Owner's Manual
Owners Manual - English - Page 6
...AVR-988, the included remote control unit (RC-1069) can also be used to other system....
q DENON system components w Non-DENON system components
• By setting the preset memory...turning the power switch on Check once again that all connections are correct and that the illustrations in these instructions may differ from the actual unit for explanation purposes. When traveling or leaving home...
Owners Manual - English - Page 10
... not bundle power cords together with connection cables. For details, refer to the equipment being connected.
Please select the types of connections, certain settings must be made on the AVR-988. Select the cables according to the instructions for subwoofer) (Black) Pin-plug cable
Speaker connections
Speaker cables
Video cables
Component video connections...
Owners Manual - English - Page 18
... using a component video cable for the digital audio connection, make the settings at menu "Input Setup"
- DBS / BS tuner
7*%&0
7*%&0 065
47*%&0 065
"6%*0
"6%*0 065
-3
015*$"065
LR
LR
Connecting the Recording Components
Carefully check the left (L) and right (R) channels and the inputs and outputs, and be used
to connect the AVR-988's DVR OUT connector.
Owners Manual - English - Page 21
...AVR-988 is used, do not
disconnect the AM loop antenna. • Make sure the AM loop antenna lead terminals do not
touch metal parts of the panel. When making connections, also refer to the AM antenna terminals.
XM Mini-Tuner and Home Dock
An F-type FM antenna cable plug can receive... antenna attached
to receive the best signal. You can be connected to the grounding system of the NEC ...
Owners Manual - English - Page 22
...: DC 12 V 150 mA MAX. For details, refer to control the AVR-988 from the external
controller.
w Turn off in association with operations on installing and operating separately sold separately) two-way communication with an RF Remote Controller or RF Remote Receiver, make the settings at
menu "Manual Setup" - b If you wish to the operating...
Owners Manual - English - Page 23
... control unit.
1 Press MENU. Menu Operations
With the AVR-988, settings and operations for hairdryers or
anything other than audio equipment. The...Select "Default Yes", then press o to reset to the default setting.
5 Press ENTER to enter the setting.
6 Press MENU to the previous item...in these outlets turns on the main unit and remote control unit
When MENU is pressed, the settings made up to...
Owners Manual - English - Page 26
... up towards the ceiling. Measurements are seated. To make the following settings before starting the auto setup procedure: • Defeat the volume and crossover controls if possible • If this position to a seat back or wall as shown in your home theater.
• It optimizes a large listening area where one would normally sit...
Owners Manual - English - Page 29
...Resets the settings to speakers. "Subwoofer" is set .
d Distance
Set distance from the listening position to "Small". Feet / Meters
Select unit for various parameters. No : S elect this procedure to set...Amp Assign" setting (vpage 30). To use and size.
( ) [Selectable items] Large Small None ( ) 2spkrs 1spkr
NOTE By default, the AVR-988's "Amp Assign" setting is set to the ...
Owners Manual - English - Page 30
...level separately for the different speakers.
• The "Crossover Frequency" can be set to receiver for HDMI video/audio output.
HDMI Audio Out
Select HDMI audio output device....Resets the settings to a higher frequency. e When the adjustments are automatically stored in the STANDARD mode. Set this setting for audio playback. When using small speakers, however, we recommend setting ...
Owners Manual - English - Page 35
... (RC-7000CI, etc.), this function can no need to "ON".
When using the AVR-988 with only the included remote control unit (RC-1069), there is off , the trigger out turns on. • Associated with the power supply of zones set this mode. Dim : Reduced display brightness. Getting Started Connections Setup Playback Remote Control...
Owners Manual - English - Page 48
...checked by pressing .
• The time for XM radio receivers by calling 1-800XMRADIO (US residents) and 1-877-GETXMSR (... or xmradio.ca (Canadian residents). Activate your XM Ready home audio system you are displayed can access the full lineup on for ...XM Satellite Radio Inc.
Basic Operation
1 Either turn or press [SAT TU] to select "XM".
2 Set [MODE SELECTOR 1] to "AUDIO". (vpage 51...
Owners Manual - English - Page 61
... (
the display.
) lights on
GOperation on the main unitH
q Press . Selecting the Input Source
GOperation on the remote control unitH
q Set [MODE SELECTOR 1] to "AUDIO" and [MODE SELECTOR 2] to
"ZONE2". w Turn and select the ZONE2's input source. GOperation on the main unitH
q Press .
To cancel, either adjust the volume or press [MUTING...
Owners Manual - English - Page 73
power outlet.
Receiving only XM channels 0 and 1. Cause
Countermeasure
• The input source assigned to • Switch to AC adapter into a power outlet.
Cause
Countermeasure
• AVR-988's XM connector and the • Check that the connections are XM Mini-Tuner and Home Dock correct.
Page 35
14 - "OFF AIR" is displayed in the XM...
Owners Manual - English - Page 76
...United Artists
Universal
V Viewstar Z Zenith
014 014 007, 016 019 011 006 010, 011 018, 019 027, 028
Satellite Receiver
A Alphastar C Chaparrali D Dishnet
054 035, 036 053
Drake
037, 038
E Echostar Dish
062, 066
G GE
048, ...-2000 DVD-2500 DVD-3000 DVD-3300
[ ]* : Preset codes set upon shipment from the factory.
*[ ] : Les codes préréglés diffèrent en fonctiom des ...
Preset Codes - Page 2
...United Artists
Universal
V Viewstar Z Zenith
014 014 007, 016 019 011 006 010, 011 018, 019 027, 028
Satellite Receiver
A Alphastar C Chaparrali D Dishnet
054 035, 036 053
Drake
037, 038
E Echostar Dish
062, 066
G GE
048, ...-2000 DVD-2500 DVD-3000 DVD-3300
[ ]* : Preset codes set upon shipment from the factory.
*[ ] : Les codes préréglés diffèrent en fonctiom des ...
Serial Protocol - Page 2
...)
ex.
SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to the following three data forms...system (AVR) if the 'request command' (COMMAND+?+CR(0x0D)) has came from a controller. Basic specification: The command by ASCII CODE, parameter expression
*ASCII CODE which can be sent within 200ms of receiving...
Similar Questions
How To Reset Demon S-301
I have a denon S-301 the last 3 years. I did't used long time .when I tested last week ,they show bl...
I have a denon S-301 the last 3 years. I did't used long time .when I tested last week ,they show bl...
(Posted by bonfit74 5 years ago)
Hdmi Dvd Output On Receiver Not Working.
No sound or picture. I have it connected to a Samsung blu ray player. HDP output works fine. Any ide...
No sound or picture. I have it connected to a Samsung blu ray player. HDP output works fine. Any ide...
(Posted by ExactoRocks 6 years ago)
