Craftsman CRAFTSMAN Support Question
Craftsman CRAFTSMAN Support Question
Find answers below for this question about Craftsman CRAFTSMAN - 1/2" AIR IMPACT WRENCH 919983.Need a Craftsman CRAFTSMAN manual? We have 1 online manual for this item!
Question posted by dcuc on September 30th, 2013
Lawnmower Won't Run
starts with gas on filter until it runs it off. checked line from tank to carb it is clear,check gas cap its ok. why won't this new craftsman lawnmower run. It sat in a garage for two years without use after being used one season(small lawn) please help kevin oil level good+new gas
Current Answers
Answer #1: Posted by freginold on December 15th, 2013 9:31 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
Hi, two things to check are the carburetor and air filter. The carb may have a blockage in one of the venturis, and the air filter might be clogged or dirty. Either of these problems could cause that issue.
Related Craftsman CRAFTSMAN Manual Pages
Owners Manual - Page 1
Owner's Manual
CORDLESS IMPACT WRENCH
1/2" Drive 18 Volt High Performance Impact Wrench Model No. 310.26825
• Safety • Operation • Maintenance • Parts • Español, p.15
CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman
Owners Manual - Page 2
... 3 SPECIFIC SAFETY RULES AND SYMBOLS 5 OPERATION 8 MAINTENANCE 12 PARTS 14 ESPAÑOL 15
WARRANTY
FULL ONE YEAR WARRANTY
If this Craftsman professional cordless impact wrench fails due to state. WARRANTY SERVICE IS AVAILABLE BY RETURNING THE TOOL TO THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES. This warranty gives you specific legal rights...
Owners Manual - Page 3
... the tool may create a risk of the tool in moving parts. Do not wear
loose clothing or jewelry.
Use only with charger listed. I Avoid accidental starting.
I...tool on. I Do not overreach.
Keep your finger on , invites accidents.
I Use safety equipment. I Remove adjusting keys or
wrenches before inserting battery pack.
Failure to lose control. Power tools...
Owners Manual - Page 4
... safety precautions to reduce the risk of
children and other small metal objects that may affect the tool's operation.
NOTE: Advises you or to reduce the risk of starting the tool accidentally. Keep
cutting tools sharp and clean. Use only accessories that are caused by hand or against your body is not in the Maintenance...
Owners Manual - Page 5
... heavier the cord. I Power tools vibrate.
Stop using an extension cord, be sure to use one heavy enough to the user.
Use of hand or power sockets will cause a drop in line voltage resulting in loss of at least 16 is recommended for Impact Wrench
I Power tools can cause flying
particles during use . Do not use the next heavier gage...
Owners Manual - Page 6
... aware of batteries may occur. They may result in a risk of electric shock, fire, or serious personal injury. I Your battery tool should not be
used , make sure:
6
I Do not charge battery tool in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar, If liquid gets...
Owners Manual - Page 7
...will not reduce this rule will reduce the risk of plug on how often you loan someone this tool, loan them to them frequently and use this tool.
I Do not disassemble charger;
Turning oft controls will reduce the risk of these exposures varies,... shock, fire, or serious personal injury.
Your risk from these chemicals are specially designed to filter out microscopic particles.
7
Owners Manual - Page 8
...to make you will enjoy years of rusted-on nuts and bolts and many other specialized uses. Direct Current Type or a characteristic of fastener turning jobs in both automotive and industrial fields.
OPERATION
APPLICATION
The Craftsman Impact Wrench is intended, you careless. SWITCH TRIGGER
To turn your impact wrench to turn your new impact wrench. Forward/Reverse Selector B. Battery Pack...
Owners Manual - Page 9
... in OFF position.
TO ATTACH BATTERY PACK TO IMPACT WRENCH
NOTE:Battery pack is controlled by the amount of accidental starting when not in use . Switch Trigger
WRIST STRAP
A wrist strap is secured to impact wrench before beginning operation. Forward/Reverse Selector B. TO REMOVE BATTERY PACK FROM IMPACT WRENCH
Figure 5: Battery Pack Removal
9 Figure 3:Forward/Reverse...
Owners Manual - Page 10
...discharged, red light should become steady after one hour red light is flashing, this tool has been shipped in possible serious injury. If after voltage has increased, normally ...green. CHARGING BATTERY PACK
The battery pack for checking or replacing.
10
Return battery pack to maintain battery pack.
Allow several cycles (using impact wrench followed by recharging) for them to do ...
Owners Manual - Page 11
... Charging Mode.
• Green LED Lighted = Fully Charged and Slow Charging to recharge. Ready Indicator Light
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
Under lengthy continuous use, the batteries in fast charging mode as normal.
11 Charging Indicator Light C. Once the battery pack cools down for approximately 1 hour before attempting to Maintain...
Owners Manual - Page 12
...Craftsman Impact Wrench
Model 310.26825
Motor voltage
18 VDC
Square drive size
1/2"
Tightening torque*
180 ft. Current draw, free speed 8.7 A
Current draw during
38 A
impacting
*Output torque is equipped with this tool. Tool... lbs. BATTERIES
The battery pack for use with nickel-cadmium rechargeable batteries. Do not abuse power tools.
However, like all batteries, they will...
Owners Manual - Page 13
..., please recycle or dispose of properly. This product contains nickel-cadmium batteries. Consult your tool for disposal, cover the battery pack's terminals with heavy-duty adhesive tape. Failure to ...destroy or disassemble battery pack or remove any of time without using it, recharge the batteries every month or two. The higher the temperature, the quicker they...
Owners Manual - Page 14
... No. 310.26825
The model number will be purchased at your CRAFTSMAN 1/2" PROFESSIONAL CORDLESS IMPACT WRENCH or when ordering repair parts. Part Number
Description
1
9-11034**
Battery Pack - 18V
2
9-11040**
Battery Charger
ZCTS1850*
Owner's Manual
3
ZCTS1850-119
Label (Logo Plate)
PB156*
Carrying ...
Similar Questions
Utility Pump Needs Replaced Day 4 No Help Sears All Shut Down Lowes No Help Ohio
submersible utility pump needs replaced day 4 and still no help ,,I went to 3 different lowes they w...
submersible utility pump needs replaced day 4 and still no help ,,I went to 3 different lowes they w...
(Posted by tabathacosta20 2 years ago)
Trigger
I have a model# 19983 craftsman air impact and I think then trigger is bad. Air doesn't pass all the...
I have a model# 19983 craftsman air impact and I think then trigger is bad. Air doesn't pass all the...
(Posted by Carlosperezej8 7 years ago)
Safe Height For Table Saw Blade Above Material
What is the recommended safe height for the saw blade to protrude above the material being cut? I sa...
What is the recommended safe height for the saw blade to protrude above the material being cut? I sa...
(Posted by leon18666 10 years ago)
What Batteries Can I Use To Replace The Dead One In My Craftsman Portable Drill?
My old batteries are dead -- 982030-001. What numbers are the 15.6V batteries that will work?
My old batteries are dead -- 982030-001. What numbers are the 15.6V batteries that will work?
(Posted by lwfogel 11 years ago)
Portable Craftsman Air Compressor
This Sears craftsman cordless portable air compressor 12 volt power supply 250 PSI blows the glass c...
This Sears craftsman cordless portable air compressor 12 volt power supply 250 PSI blows the glass c...
(Posted by Zazalooie 12 years ago)