Craftsman 21602 Support Question
Craftsman 21602 Support Question
Find answers below for this question about Craftsman 21602 - 16 in. Variable Speed Scroll Saw.Need a Craftsman 21602 manual? We have 1 online manual for this item!
Question posted by sandranunnelee on November 28th, 2010
My New Variable Speed Scroll Saw Won't Start.
There's power to the unit as the light works. The saw occasionally ran very slowly, much slower than the speed adjustment allowed. It would then run properly after a moment or two. Now it won't start at all. Could it be the switch?
Current Answers
Related Craftsman 21602 Manual Pages
Operation Manual - Page 1
Operator's Manual
16 in China VARIABLE SPEED SCROLL SAW Model No. 137.216020
C
us
CAUTION:
Before using this Scroll Saw, read this manual and follow all its Safety Rules and Operating Instructions
• Safety Instructions • Installation
• Operation • Maintenance • Parts List
Sears, ...
Operation Manual - Page 2
... Crystalline silica from bricks, cement and other rights which vary from these chemicals, work in material or workmanship within one year from the date of California to cause... Power Tool Safety Scroll Saw Safety Electrical Requirements and Safety Accessories and Attachments Tools Needed for Assembly Carton Contents Know Your Scroll Saw Glossary of Terms Assembly and Adjustments ...
Operation Manual - Page 6
... or others.
18. Wear protective hair covering to hold work when practical. DISCONNECT TOOLS FROM POWER SOURCE before plugging the tool in moving parts, breakage of moving parts. tool can throw foreign PoRbjOecTtEsCTinItOoNth. WEAR A FACE MASK OR DUST MASK. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Everyday eyeglasses have only impact-resistant lenses. CHECK FOR...
Operation Manual - Page 8
... operation, the stand or workbench MUST be fastened to the floor.
, THIS SCROLL SAW is intended for indoor use only.
, TENSION BLADE PROPERLY before starting the saw. Recheck and adjust tension as needed.
10. , READ AND UNDERSTAND all debris before resuming operation.
, YOUR SCROLL SAW MUST BE SECURELY FASTENED to a stand or workbench. HOLD WORKPIECE FIRMLY against the...
Operation Manual - Page 9
... damaged should be properly repaired or replaced before using the tool.
26. NEVER REACH under the scroll saw with workpiece pressing against the blade. Wedge open the kerf and back the blade out of moving blade.
20. DO NOT START the saw table when motor is supported at the rate the saw and unplug the power cord. Check...
Operation Manual - Page 12
...recommended for this scroll saw blades
Sears may cause hazards. See your Sears Hardware Department or see the Sears Power and Hand Tool Catalog for ...tool or create accessories not recommended for the following accessories:
ITEM Pin-end saw blades Plain-end saw . AVAILABLE ACCESSORIES
WARNING I To avoid injury, do not attempt to possible serious injury. Supplied
7
Not Supplied Adjustable...
Operation Manual - Page 13
...frame.
2.
Scroll Saw
Pin-end saw blade Plain-end saw on a secure stationary work surface.
3. Remove the scroll saw from the ...scroll saw by the arm that holds the blade, this saw in damage to clean the scroll saw by lifting the saw .
1. To avoid fire and toxic reaction, never use gasoline, naphtha, acetone, lacquer, thinner or similar highly volatile solvents to the tool...
Operation Manual - Page 15
... it at the angle desired for bevel cutting.
Adjust the speed to the desired setting, between 400 to extra ...Variable switch dial allows greater versatility when cutting a variety of one bent tooth to 45 ° when the table is tilted for more accurate cuts.
FEED-
Slight movement of sight for bevel cutting. TABLE LOCK KNOB - This may be used to its original tension. SCROLL SAW...
Operation Manual - Page 17
....
2
2. If mounting the scroll saw to the power source until it is completely assembled and adjusted and you have read and understood this saw
is located on the right rear... (1) is NOT supplied with the saw body. length as shown in Fig. B
MOUNTING SCROLL SAW TO WORK
SURFACE (FIG.
STORING THE T-WRENCH (FIG. Position the shaft of the scroll saw . Fig. B) The left rear...
Operation Manual - Page 18
...-38 mm (1-11/16 in-1-1/2 in place unless the vacuum is provided for your convenience. E, F) This scroll saw will keep your saw with the hose in ) dust port adapter (4) is turned on the left side of base. Fig. I_h, WARNING To prevent fire hazard, clean and remove sawdust from the power source, then removing the...
Operation Manual - Page 20
...whenever fine, accurate and intricate work is too tight, turn the switch OFF and remove power cord plug from accidental starting, always turn counterclockwise. If ... on 3/4 in the table. Plain-end type blades are properly located in the upper blade holder (6). (Fig. J)
PLAIN-END BLADE REMOVAL AND INSTALLATION This scroll saw accepts 5-inch plainend or pin-end blades to use finer ...
Operation Manual - Page 22
...starting, always turn the lever clockwise. NOTE: Apply slight downward pressure against the upper arm (4-Fig. If too loose, turn the switch OFF
and unplug the scroll saw before
moving, replacing the blade or
3
making adjustments.
2
4. P)
900 (0 °) Bevel Adjustment...right angle to turn counterclockwise. Q, R) 1. Insert the new blade into the upper blade holder.
5. O)
3. ...
Operation Manual - Page 24
...speeds on .
T
9.5-48
9.5-33
10-37
The following table represents suggestions for straight and large curve cutting operations. BLADE SELECTION (FIG.
When purchasing blades, refer to prevent the workpiece from accidental starting, always turn the switch OFF and unplug the scroll saw...pulled upward by the saw before moving, replacing the blade or making adjustments. The type of ...
Operation Manual - Page 26
... lights go out) push the knob "OFF". Also, in ON position, then connect the power supply, the motor will start the saw.
OVERLOAD BREAKER (FIG.
The blade stroke rate may be reduced to allow the blade teeth to remove cut a variety of your own safety, always push the switch "OFF" when the scroll saw is equipped with a
variable speed...
Operation Manual - Page 27
... foot slightly above the top surface of the workpiece and to the power source outlet.
1. CAUTION: In order to avoid
uncontrollable lifting of the workpiece.
4. Set the variable speed control knob (4) to turning the scroll saw .Duringthatperiodof timeit isexpectedthatsomebladeswill breakuntilyoulearnhowto use withyourscrollsaw,considevr ery fine,narrowbladesto scrollcutin thinwood1...
Operation Manual - Page 28
...starting, make sure the switch is in the OFF position and the plug is complete, move the table to the power source outlet before moving, replacing the blade or making adjustments. Turn the scroll saw...proper angle, using the degree scale (6) and the pointer (7). 4. Tighten the table lock knob (5). 5. Position the workpiece on the left are possible on this unit. 1. When turning the scroll saw ...
Operation Manual - Page 29
... scroll
saw ON. Slowly ...scroll saw ON while the workpiece is secure.
4. NOTE: When cutting a narrow workpiece use push sticks. Clamp the straight edge (4) to the blade at that distance.
2. Recheck your measurements, using the workpiece to the power source outlet before moving, replacing the blade or making adjustments. X 3
5
29 X)
,A WARNING t To avoid injury from an accidental starting...
Operation Manual - Page 30
... the tension knob (2). 5. Follow the process, items 3-8, under FREEHAND CUTTING OPERATIONS.
6. Install the blade (3) through the hole in . When finished making the interior scroll cuts simply turn the scroll saw table with the workpiece hole (4) over the access hole in the workpiece. 2. Place the workpiece on the workpiece
(1).
Fig. Remove the blade by...
Operation Manual - Page 32
... section.
1.
WARNING I To avoid injury from accidental starting, always turn switch OFF and unplug the tool before using saw .
Loosen blade holder lock screw
holding blade holder to repair this manual for proper mounting
NOTE: There will occur. Use narrow blade. See BLADE
4. Any attempt
to arms. Adjust position of 1.
See OVERLOAD
BREAKER section.
See...
Operation Manual - Page 34
... COVER
1 Any attempt to repair or replace electrical parts on this Scroll Saw may create a HAZARD unless repair is available at your nearest Sears Service Center. HD. ...12
2
0KMR HEX. SOC. RE. RE. TAPPING SCREW
M416-8
4
0KA4
CR. RE. 16 in. VARIABLE SPEED SCROLL SAW
MODEL NO. 137.216020
WARNING {
When servicing use only CRAFTSMAN replacement parts. SCREW AND WASHER ...
Similar Questions
16' Scroll Saw Variable Switch Assembly
I need a 16" Scroll Saw Variable Switch Assembly
I need a 16" Scroll Saw Variable Switch Assembly
(Posted by ldsilva1 9 years ago)
Craftsman 18 Inch Variable Speed Scroll Saw Model 315.216090
I would like pictures or diagrams of pc board/s connections. Any problems with yours?
I would like pictures or diagrams of pc board/s connections. Any problems with yours?
(Posted by dianechristensen5054 9 years ago)
It Is Getting Power. The Light Works But The Saw Will Not Operate.
(Posted by Anonymous-123838 10 years ago)
My Saw Changes Speeds By Itself,
When in use my saw will go fast then slow ndown and then speed up on its own, it will not stay at on...
When in use my saw will go fast then slow ndown and then speed up on its own, it will not stay at on...
(Posted by nhuwalk 11 years ago)
Maximum Cut Depth For 21609 Scroll Saw
I can't find the maximum depth of cut that you can make with the 21609 scroll saw - can you please t...
I can't find the maximum depth of cut that you can make with the 21609 scroll saw - can you please t...
(Posted by brian78088 12 years ago)