Craftsman 21602 Support Question
Craftsman 21602 Support Question
Find answers below for this question about Craftsman 21602 - 16 in. Variable Speed Scroll Saw.Need a Craftsman 21602 manual? We have 1 online manual for this item!
Question posted by dianechristensen5054 on July 12th, 2014
Craftsman 18 Inch Variable Speed Scroll Saw Model 315.216090
I would like pictures or diagrams of pc board/s connections. Any problems with yours?
Current Answers
Related Craftsman 21602 Manual Pages
Operation Manual - Page 1
...
16 in China VARIABLE SPEED SCROLL SAW Model No. 137.216020
C
us
CAUTION:
Before using this Scroll Saw, read this manual and follow all its Safety Rules and Operating Instructions
• Safety Instructions • Installation
• Operation • Maintenance • Parts List
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit our Craftsman website: www,sears,com/craftsman...
Operation Manual - Page 2
...Symbols Power Tool Safety Scroll Saw Safety Electrical Requirements and Safety Accessories and Attachments Tools Needed for Assembly Carton Contents Know Your Scroll Saw Glossary of Terms Assembly and Adjustments Operation Maintenance
Troubleshooting Guide Parts List
PAGE
2 3 4 5 8 10 12 12 13 14 15 17 26 31
32 34
CRAFTSMAN ONE YEAR FULL WARRANTY
If this Craftsman tool fails due...
Operation Manual - Page 3
...must be connected to the tool, use proper circuit protection. This tool is wired ...at the factory for 110-120 Volt operation. WARNING I
To avoid electrical hazards, fire hazards or damage to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker. MOTOR Power Source Speed... Control
TABLE Tilt
1.6 A, 120 V AC, 60 Hz Electric
45 o Left
SAWDUST BLOWER
BLADE Speed...
Operation Manual - Page 6
...ANSI Safety standard Z87.1. CHECK FOR DAMAGED PARTS. REDUCE THE RISK OF UNINTENTIONAL STARTING. Sawing operation produces dust.
14. Make sure switch is damaged should be properly repaired or...you when they break.
13. DISCONNECT TOOLS FROM POWER SOURCE before plugging the tool in moving parts, breakage of injury to yourself or others.
18. It is recommended. Consult this ...
Operation Manual - Page 8
... hand or finger positions, where a sudden slip could occur if the tool tips over or you accidentally hit the cutting tool. Replace missing, damaged, or failed parts before resuming operation.
, YOUR SCROLL SAW MUST BE SECURELY FASTENED to be fastened to the floor.
, THIS SCROLL SAW is intended for indoor use only.
, TENSION BLADE PROPERLY before...
Operation Manual - Page 9
....
21. 16.TURN THE SAW OFF AND
UNPLUG THE CORD if the blade binds in the saw table when motor is running.
25. THINK SAFETY.
9 NEVER REACH under the scroll saw kerf while being backed out of moving blade.
20. Parts that are damaged should be properly repaired or replaced before using the tool.
26. TURN...
Operation Manual - Page 12
... have completely read the instruction or Operator's Manual for use with this tool. Supplied
7
Not Supplied Adjustable Wrench
3 mm T-Wrench
_,1.1 i.l.n,_
Combination Square
Phillips Screwdriver 5 mm Hex Wrench
Visit your nearest Sears store or Power and Hand Tool Catalog for this scroll saw blades
Sears may cause hazards. AVAILABLE ACCESSORIES
WARNING I To avoid injury, do...
Operation Manual - Page 13
... gasoline, naphtha, acetone, lacquer, thinner or similar highly volatile solvents to the tool. CAUTION: Do not lift this may result in until the missing or damaged part is replaced, and assembly is complete. Scroll Saw
Pin-end saw blade Plain-end saw by the back of the upper frame.
2. Check each one with the illustration...
Operation Manual - Page 15
... or wrenches.
TABLE LOCK KNOB -
DEFLECTION - Slight movement of least resistance. BLADE STORAGE - VARIABLE SPEED CONTROL KNOB -
Rate of table angle from under the table and base. BLADE GUARD FOOT LOCK...SAWDUST BLOWER - Adjust the speed to the desired setting, between 400 to raise or lower the foot and lock it at the angle desired for bevel cutting. SCROLL SAW TERMS
BEVEL SCALE - ...
Operation Manual - Page 17
... minutes
WARNING J
To avoid injury, do not connect this scroll saw to
reduce noise and vibration.
2
2. If mounting the scroll saw to a
workbench, a solid wood bench is
preferred over a plywood board to the power source until it is completely assembled and adjusted and you have read and understood this saw
is located on the right rear side...
Operation Manual - Page 18
...connected to direct air at the front of base. E, F) This scroll saw holding the plate cover. DO NOT operate the saw housing, attach a vacuum hose (3) to the bellows seat (2). 3.
If excessive sawdust buildup occurs inside the saw...the workpiece. NOTE: A 43-38 mm (1-11/16 in-1-1/2 in place unless the vacuum is provided for your saw . Fig. D) 1.
I_h, WARNING To prevent ...
Operation Manual - Page 20
... loose, turn the switch OFF and remove power cord plug from accidental starting, always turn the knob clockwise. J)
2. J)
PLAIN-END BLADE REMOVAL AND INSTALLATION This scroll saw accepts 5-inch plainend or pin-end blades to use finer blades for cutting a thinner kerf. Fig. J
I,A WARNING To avoid injury from 1 power source before removing or...
Operation Manual - Page 22
... the tension knob (5-Fig. O) when installing the blade into the upper blade holder slot (3-Fig. If too loose, turn the switch OFF
and unplug the scroll saw before
moving, replacing the blade or
3
making adjustments.
2
4. If there is space between the square and blade, adjust the table angle until the tip of...
Operation Manual - Page 24
...the sawdust off the table, and will determine the number of blades and speeds on . NOTE: When using blades, sometimes speeds must be installed with a wide variety of -sight when cutting.
When ...prevent the workpiece from accidental starting, always turn the switch OFF and unplug the scroll saw accepts 5-inch length blades with the teeth pointing downward, as an example, but practice and ...
Operation Manual - Page 26
...saw is equipped with a
variable speed control knob (1). U
VARIABLE SPEED SWITCH (FIG. ON/OFF SWITCH (FIG. When feeding the workpiece into the blade do not force the leading edge of the workpiece into the blade slowly because the teeth of your own safety, always push the switch "OFF" when the scroll saw...ON position, then connect the power supply, the motor will start the saw is not in ...
Operation Manual - Page 27
... prior to turning the scroll saw .Duringthatperiodof timeit isexpectedthatsomebladeswill breakuntilyoulearnhowto use withyourscrollsaw,considevr ery fine,narrowbladesto scrollcutin thinwood1/4in.thickor less.Use widerbladesfor thickermaterials
butthiswillreducetheabilityto cut tightcurves.
11.Thissawuses5 in the OFF position and the plug is not connected to the desired speed by tightening the...
Operation Manual - Page 28
The blade will deflect, reducing accuracy of cut is not connected to the power source outlet before moving, replacing the blade or making adjustments. V
2 1 ... under FREEHAND CUTTING OPERATION.
9 Fig. CAUTION: Do not force the leading edge of the blade (9). Turn the scroll saw ON, position the workpiece against scrap wood prior to the left are possible on the left and right side of the...
Operation Manual - Page 29
...speed by loosening the blade guard foot lock knob (2) on the right side of wood (Thickness to the blade at that distance.
2. Fig. Turn the scroll saw ON while the workpiece is not connected...surface of the blade (3) to the table (5).
3. Tools Needed (Not Included)
QUANTITY DESCRIPTION
2
Small O-clamps
1
Ruler or measuring tape
12-inch straight scrap
1
of the upper arm. Position the...
Operation Manual - Page 30
... a 1/4 in the workpiece. 2. Place the workpiece on the workpiece
(1). Install the blade (3) through the hole in the table (5). 4. When finished making the interior scroll cuts simply turn the scroll saw table with the workpiece hole (4) over the access hole in the workpiece and tighten the tension knob (2). 5. Y) 1.
Remove the blade by turning the...
Operation Manual - Page 34
....0-6 M5"0.8-10 M61.0-25 M81.25-30 M61.0-16 M5"0.8-10
Qty LD. RE. PAN HD. TAPPING SCREW
M416-8
4
0KA4
CR. PAN HD. TRUSS HD. RE. HD. SCREW
Size
Qfy
M5 9.8-8
5
0K72
CR. TRUSS HD. RE. VARIABLE SPEED SCROLL SAW
MODEL NO. 137.216020
WARNING {
When servicing use only CRAFTSMAN replacement parts. CAP BOLT HEX. SCREW
M5...
Similar Questions
16' Scroll Saw Variable Switch Assembly
I need a 16" Scroll Saw Variable Switch Assembly
I need a 16" Scroll Saw Variable Switch Assembly
(Posted by ldsilva1 9 years ago)
Repairing Broken Drive Belt On Craftman Band Saw Model 351.214190
How To Remove The Lower Wheel On Craftman Band saw Model 351.214190. Because The Drive Belt Is broke...
How To Remove The Lower Wheel On Craftman Band saw Model 351.214190. Because The Drive Belt Is broke...
(Posted by AVERBECK 10 years ago)
My Saw Changes Speeds By Itself,
When in use my saw will go fast then slow ndown and then speed up on its own, it will not stay at on...
When in use my saw will go fast then slow ndown and then speed up on its own, it will not stay at on...
(Posted by nhuwalk 11 years ago)
Hello In Need Battery And Charger For Impact Driver Model 315.114831
need battery and charger for model 315.114831 impact driver
need battery and charger for model 315.114831 impact driver
(Posted by bell753 11 years ago)
My New Variable Speed Scroll Saw Won't Start.
There's power to the unit as the light works. The saw occasionally ran very slowly, much slower than...
There's power to the unit as the light works. The saw occasionally ran very slowly, much slower than...
(Posted by sandranunnelee 13 years ago)