Acer AC711 Support Question
Acer AC711 Support Question
Find answers below for this question about Acer AC711.Need a Acer AC711 manual? We have 2 online manuals for this item!
Question posted by kobaiaac on April 30th, 2014
How To Repair A Power Switch On Acer Ac711 Monitor
how to troubleshoot the problem with power switch and repair. I opened the case and see no burnt components nor broken power fuse everything fine so I blame the power switch so any ideas to this matter please help
Current Answers
Related Acer AC711 Manual Pages
AC 711 User Guide - Page 1
... moisture. 6. T he wall socket must be equipped with a non-fused grounded conductor contact for any improvement with the original parts, for a long period of this device. 15. The power cable must be laid in a fire or an electric shock. 14. Never open the casing of this guide; The device was exposed to be used...
AC 711 User Guide - Page 2
... )
This equipment has been tested and found to comply with the limits for help. n Connect the equipment with a power socket on a circuit different from the monitor. Place the monitor with its tube down on the front panel when you place the monitor with the instructions, may void t he user'sauthority to nearby radio and television...
AC 711 User Guide - Page 3
... plug the other end into an electrical outlet that of the screen image.
Ø Energy Star compliant for easy and accurate adjustment of the monitor.
4.
Installation
1. Connect the power cord to the 15-pin mini D-sub (VGA) on the back panel of the swivel base for maximum viewing comfort.
Using state-of...
AC 711 User Guide - Page 4
... key to display the OSD menu.
2. Power LED Indicator
LED color Status
Green
On
Amber Sleep
3. Backward and Forward Buttons
• Backward button (left arrow) moves backward through menu options or decreases adjustment levels.
• Forward button (right arrow) moves forward through menu options or increases adjustment levels. Power Switch Turns the monitor on
2.
AC 711 User Guide - Page 5
Size
Increase and decrease screen height
V. RGB Analog 0.7Vp -p/75 Ohm a. Resolution
15-pin mini D-sub
30-70 50-160 1280 x 1024
Power
Consumption Power Supply
Power Management
Max. 75 W
100 - 240VAC (W/I CE Mark) 50/60Hz Complies with EPA Energy Star ,VESA, Nutek
Display Modes
Preset
6
By User
14
Operating
Operating Temperature 0-...
AC 711 User Guide - Page 7
...PC. Problem: No display appears on screen.
@ Make sure that the computer switch is in a wave pattern.
@ Move any electrical devices that can cause interference away from the monitor.
...are not turned to their dimmest
position. Problem: Power LED is not lit when monitor is plugged
into a power extension cord or a surge protector. Troubleshooting
Please refer to the following solutions for more...
AC711 Monitor Service Guide - Page 2
... both X and Y and axis. The measured value of linearity shall be less than 5%(p) or 6%(s) when calculated using adjcent lattices. ALIGNMENT PROCEDURE • Warm up the monitor for at least 30 minutes before adjustment. • Set the front of an image displayed on the CRT must meet the following requirements, with reference...
AC711 Monitor Service Guide - Page 4
... x=283 ( x=295 for 7500;
F.1.6 Disable the video pattern( for 6500 ) ± 3. F.1.10 Adjust brightness control to get y=297 ( y=315 for 7500 ; x=313 for 6500 ) ± 3
F.1.8 Fine tune the bias G and R for x=283 , y=297 ( x=299, y=315 for 7500 ; bias is 0, set the maximum value of R.G.B. F.1.2 Disconnect R.G.B.
F.1.4 Manual alignment P103 must be short...
AC711 Monitor Service Guide - Page 5
F.1.13 Fine tune the gain G and R for x=283 , y=297 ( x=299, y=315 for 6500 ) ± 2
F.1.14 Check 150 >Y> 130 cd/mm, if not , adjust G to get Y>130 cd/mm, then repeat item 2.5.12
F.1.15 Change pattern to fall white, adjust SB to get 92< Y x=313, y=329, for 7500;
AC711 Monitor Service Guide - Page 11
...circuit includes four major parts, the power supply circuit, the deflection circuit, the video circuit and the digital control circuit. is a 17" multisync color monitor. A. C. From the key ... +53V: For B+ Boost circuit. (5) +80V: For video circuit (6) 9.2V: for MIRCO- POWER SUPPLY Transfer AC source to 160hz. 3. INTRODUCTION:
C708 is the function block diagram. It includes: (1)...
AC711 Monitor Service Guide - Page 15
... Q903 and turning off . During the On-time of Q901. Primary current is determined by R919, C916. The external signal "SYN+ & SYN−"
E. POWER SAVING CKT: The monitor has ON and OFF states.
The equation is defined by voltage feedback. In this store/release action are needed to charge the outputs to...
AC711 Monitor Service Guide - Page 22
POWER SUPPLY CHECK
22 TROUBLESHOOTING
A. 7.
Similar Questions
How To Remove Acer P206hv Monitor Back Cover?
how to remove acer p206hv monitor back cover? the ac power point is burnt and i would like to remove...
how to remove acer p206hv monitor back cover? the ac power point is burnt and i would like to remove...
(Posted by lvictorlincoln 5 years ago)
Colors Are All 'wrong' On My Acer G196hql Monitor...
I recently noticed after rebooting my PC today that my Acer monitor is showing multiple hues/shades ...
I recently noticed after rebooting my PC today that my Acer monitor is showing multiple hues/shades ...
(Posted by ppaternacht 8 years ago)
Acer Al1913 Monitor
I need a driver for my Acer AL1913 Monitor so I can use it with my MacBook Pro HD 'laptop'. Which d...
I need a driver for my Acer AL1913 Monitor so I can use it with my MacBook Pro HD 'laptop'. Which d...
(Posted by wilannlog 11 years ago)
How Do I Fix Blue Box
I keep getting a blue box in the centre of my screen. It comes and goes. How do I fix it.
I keep getting a blue box in the centre of my screen. It comes and goes. How do I fix it.
(Posted by christopherlesliebarrett 11 years ago)