Owners Manual
Page 12
...'s speaker impedance to 5.1-channel speaker system. Speaker system (the number of other channels. to 7.1-channel system, and RX-V473 supports 2- 1 Speaker placement 2 3 4 5 6 7 8 9 10 1 Placing speakers Select the speaker layout for the number of speakers that you can also use 4-ohm speakers as the front speakers. This section describes the representative speaker layout examples.
...'s speaker impedance to 5.1-channel speaker system. Speaker system (the number of other channels. to 7.1-channel system, and RX-V473 supports 2- 1 Speaker placement 2 3 4 5 6 7 8 9 10 1 Placing speakers Select the speaker layout for the number of speakers that you can also use 4-ohm speakers as the front speakers. This section describes the representative speaker layout examples.
Owners Manual
Page 14
... front display. PREPARATIONS ➤ Placing speakers En 14 z (power) STRAIGHT 3 Check that "SP IMP." is configured for 8-ohm speakers. You are now ready to "6 Ω MIN". In this case, you can also use 4-ohm speakers as the front speakers. 1 Before connecting speakers, connect the power cable to standby mode and remove the...
... front display. PREPARATIONS ➤ Placing speakers En 14 z (power) STRAIGHT 3 Check that "SP IMP." is configured for 8-ohm speakers. You are now ready to "6 Ω MIN". In this case, you can also use 4-ohm speakers as the front speakers. 1 Before connecting speakers, connect the power cable to standby mode and remove the...
Owners Manual
Page 80
...front panel, press z (power). Repeat from Step 1. • The registered remote control codes (p.82) are not cleared even if you connect 8-ohm or higher speakers to standby mode. 2 While holding down STRAIGHT on the unit. The new settings take effect. REMOTE ID TU TV FORMAT INIT ...of the following steps within 1 minute. You can set the unit to standby mode and turn it on the remote control using multiple Yamaha AV receivers, you connect 6-ohm speakers to enter "5019" (ID1) or "5020" (ID2). CONFIGURATIONS ➤ Configuring the system settings (ADVANCED SETUP menu) En ...
...front panel, press z (power). Repeat from Step 1. • The registered remote control codes (p.82) are not cleared even if you connect 8-ohm or higher speakers to standby mode. 2 While holding down STRAIGHT on the unit. The new settings take effect. REMOTE ID TU TV FORMAT INIT ...of the following steps within 1 minute. You can set the unit to standby mode and turn it on the remote control using multiple Yamaha AV receivers, you connect 6-ohm speakers to enter "5019" (ID1) or "5020" (ID2). CONFIGURATIONS ➤ Configuring the system settings (ADVANCED SETUP menu) En ...
Owners Manual
Page 115
When connecting 6-ohm speakers, set the unit's speaker impedance to the FRONT (//\) terminals. One is for the positive (+) terminals. a Remove approximately 10 mm (3/8") of insulation from the AC ... connecting the negative (-) terminals of the unit and the speaker, and the other or come into contact with built-in "Owner's Manual". • (Except for 8-ohm speakers. If the speaker cables short circuit, "Check SP Wires" will appear on the front display when the unit is configured for U.S.A. and Canada models...
When connecting 6-ohm speakers, set the unit's speaker impedance to the FRONT (//\) terminals. One is for the positive (+) terminals. a Remove approximately 10 mm (3/8") of insulation from the AC ... connecting the negative (-) terminals of the unit and the speaker, and the other or come into contact with built-in "Owner's Manual". • (Except for 8-ohm speakers. If the speaker cables short circuit, "Check SP Wires" will appear on the front display when the unit is configured for U.S.A. and Canada models...