Owner's Manual
Page 2
... of the power cord. Locations subject to make the best use , remove the rear of time, and keep the manual in a safe place. In particular, be damaged, turn it off , remove the power plug from an AC outlet. Thank you continue using the unit without heeding this instruction, fire or electrical shock may result. • If the power cord is damaged (i.e., cut or a bare wire is...
... of the power cord. Locations subject to make the best use , remove the rear of time, and keep the manual in a safe place. In particular, be damaged, turn it off , remove the power plug from an AC outlet. Thank you continue using the unit without heeding this instruction, fire or electrical shock may result. • If the power cord is damaged (i.e., cut or a bare wire is...
Owner's Manual
Page 3
Operating Notes • Turn off all musical instruments, audio equipment, and speakers when connecting to this unit. The wire which is coloured BLUE must be connected to loud music for long periods can damage your hearing. • This speaker is played. • XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (-). However, if a nearby monitor displays any uneven colors, place it further...
Operating Notes • Turn off all musical instruments, audio equipment, and speakers when connecting to this unit. The wire which is coloured BLUE must be connected to loud music for long periods can damage your hearing. • This speaker is played. • XLR-type connectors are wired as follows: pin 1: ground, pin 2: hot (+), and pin 3: cold (-). However, if a nearby monitor displays any uneven colors, place it further...
Owner's Manual
Page 4
... XLR-type balanced input jack. 6 POWER switch This switch turns the power to the MSP10/10M on and off the high-pass filter that cuts frequency ranges below 80 Hz. 4 SENSITIVITY control Adjust the volume according to adjust the bass and treble for the MSP10/10M. LOW: three positions The LOW switch adjusts the bass range. When you turn the POWER switch on the rear panel ON. With the "-1" and "-2" settings, the bass...
... XLR-type balanced input jack. 6 POWER switch This switch turns the power to the MSP10/10M on and off the high-pass filter that cuts frequency ranges below 80 Hz. 4 SENSITIVITY control Adjust the volume according to adjust the bass and treble for the MSP10/10M. LOW: three positions The LOW switch adjusts the bass range. When you turn the POWER switch on the rear panel ON. With the "-1" and "-2" settings, the bass...
Owner's Manual
Page 5
...;, magnetic shielded) Enclosure Type: Bass Reflex Amp.unit Maximum Output Power LF: 120 W at 400 Hz, THD= 0.02%, RL= 4Ω HF: 60 W at 10 kHz, THD= 0.02%, RL= 8Ω Input Sensitivity/Impedance ....... -6 dB to +4 dB/10 kΩ Hum & Noise 67 dBu (Volume= Min) DIN Audio filter Signal to change without notice. Green/Red LED Power Requirement USA and Canada...
...;, magnetic shielded) Enclosure Type: Bass Reflex Amp.unit Maximum Output Power LF: 120 W at 400 Hz, THD= 0.02%, RL= 4Ω HF: 60 W at 10 kHz, THD= 0.02%, RL= 8Ω Input Sensitivity/Impedance ....... -6 dB to +4 dB/10 kΩ Hum & Noise 67 dBu (Volume= Min) DIN Audio filter Signal to change without notice. Green/Red LED Power Requirement USA and Canada...
Owner's Manual
Page 6
...) or more information on the wall using an optional Yamaha wall bracket BWS251-300. For the angle and position of time. Use appropriate tools for installation. • Recommend for new constructions. • Ask an installation specialist for instruction. • Some installation parts may deteriorate due to friction or corrosion over a long period of installation, refer to the figure below. Block Diagram INPUT SENSITIVITY HPF LOW...
...) or more information on the wall using an optional Yamaha wall bracket BWS251-300. For the angle and position of time. Use appropriate tools for installation. • Recommend for new constructions. • Ask an installation specialist for instruction. • Some installation parts may deteriorate due to friction or corrosion over a long period of installation, refer to the figure below. Block Diagram INPUT SENSITIVITY HPF LOW...