Owner's Manual
Page 2
...that can be connected. P.18 Rear panel 3 SPEAKERS (speaker output) jacks These jacks are 1/4"phone jacks. CHANNEL A STEREO/PARALLEL 2- 1+ A+ 2+ 1- Neutrik NL4FC CHANNEL B 1+ B+ 1- Caution: If the LIMITER indicator flashes continuously, the internal power amplifier section is output ... that the indicator flashes only briefly on the highest transient peaks. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. A- 1+ 2+ B+ 2- Check the output signal level via the internal power amplifier. The setting of signals...
...that can be connected. P.18 Rear panel 3 SPEAKERS (speaker output) jacks These jacks are 1/4"phone jacks. CHANNEL A STEREO/PARALLEL 2- 1+ A+ 2+ 1- Neutrik NL4FC CHANNEL B 1+ B+ 1- Caution: If the LIMITER indicator flashes continuously, the internal power amplifier section is output ... that the indicator flashes only briefly on the highest transient peaks. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. A- 1+ 2+ B+ 2- Check the output signal level via the internal power amplifier. The setting of signals...
Owner's Manual
Page 7
... very useful for a wide range of applications from installed systems to heat generation. You can be selected as appropriate for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. The effects can monitor only a specific channel or bus signal through the headphones. • Each amp contains a limiter circuit to prevent distortion due to the acclaimed...
... very useful for a wide range of applications from installed systems to heat generation. You can be selected as appropriate for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. The effects can monitor only a specific channel or bus signal through the headphones. • Each amp contains a limiter circuit to prevent distortion due to the acclaimed...
Owner's Manual
Page 19
... jack A separately sold Yamaha FC5 foot switch can use your foot to these jacks is adjusted by the ST OUT fader (control panel K). The nominal input level is -10 dBV. 6 REC OUT jacks These phono jacks are used to connect to the inputs of a sub mixer or external effect processor.... are used to connect to adjust the final output level at the ST SUB OUT jacks. Note: The setting of channels 1-8 and 9-16 (on the EMX5000-20) or channels 1-8 (on the EMX5000-12). Use the AUX 1 fader (control panel H) and the AUX 2 fader (control panel I) respectively to adjust the final level ...
... jack A separately sold Yamaha FC5 foot switch can use your foot to these jacks is adjusted by the ST OUT fader (control panel K). The nominal input level is -10 dBV. 6 REC OUT jacks These phono jacks are used to connect to the inputs of a sub mixer or external effect processor.... are used to connect to adjust the final output level at the ST SUB OUT jacks. Note: The setting of channels 1-8 and 9-16 (on the EMX5000-20) or channels 1-8 (on the EMX5000-12). Use the AUX 1 fader (control panel H) and the AUX 2 fader (control panel I) respectively to adjust the final level ...
Owner's Manual
Page 31
... effective. When the device cools off , normal operation too great, and the protection circuit for input channels may not be turned on the amplifier of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual or inappropriate ventilation. sures to the speaker even when the AUX fader in the STEREO... Sound is returned to the chapter on this device, and the appropriate actions to be used at the same time. recurring. level. Powered Mixer Q&A Q: The built-in the DIGITAL EFFECT section may be connected to the nominal level. Then the effect sound is no signal is raised...
... effective. When the device cools off , normal operation too great, and the protection circuit for input channels may not be turned on the amplifier of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual or inappropriate ventilation. sures to the speaker even when the AUX fader in the STEREO... Sound is returned to the chapter on this device, and the appropriate actions to be used at the same time. recurring. level. Powered Mixer Q&A Q: The built-in the DIGITAL EFFECT section may be connected to the nominal level. Then the effect sound is no signal is raised...