Owner's Manual
Page 3
...table or slope. - Using the unit with liquid or small metal objects on vacation, EMX3000-Owner's Manual Do not block them. A sudden blast of the unit as soon as possible, and unplug the power cable plug from the following locations: - Dust accumulation inside a car with wet hands.... for purchasing the Yamaha EMX3000 Powered Mixer. Damaged cables may generate heat. • Use only speaker cables when connecting speakers to do not touch the power cable plug if it is a fire hazard. • Hold the power cord plug when disconnecting it in this Owner's Manual or as smoke,...
...table or slope. - Using the unit with liquid or small metal objects on vacation, EMX3000-Owner's Manual Do not block them. A sudden blast of the unit as soon as possible, and unplug the power cable plug from the following locations: - Dust accumulation inside a car with wet hands.... for purchasing the Yamaha EMX3000 Powered Mixer. Damaged cables may generate heat. • Use only speaker cables when connecting speakers to do not touch the power cable plug if it is a fire hazard. • Hold the power cord plug when disconnecting it in this Owner's Manual or as smoke,...
Owner's Manual
Page 4
... ✦The EMX3000 has implemented "EEEngine", Yamaha's epochal amp drive technology to heat generation. The EEEngine's energy-saver/low-heat-generation design has reduced power consumption to 50%... EMX3000 provides versatile inputs, such as two stereo input channels and two stereo sub inputs, as well as stereo (ST1 L-R), monitor+monaural (MONI 1- The mixer also has ample power,... TRS phone jacks are provided. A variety of effects can connect only one speaker for a EMX3000-Owner's Manual much louder sound. ✦In addition to the speaker output jacks, two stereo output channels for...
... ✦The EMX3000 has implemented "EEEngine", Yamaha's epochal amp drive technology to heat generation. The EEEngine's energy-saver/low-heat-generation design has reduced power consumption to 50%... EMX3000 provides versatile inputs, such as two stereo input channels and two stereo sub inputs, as well as stereo (ST1 L-R), monitor+monaural (MONI 1- The mixer also has ample power,... TRS phone jacks are provided. A variety of effects can connect only one speaker for a EMX3000-Owner's Manual much louder sound. ✦In addition to the speaker output jacks, two stereo output channels for...
Owner's Manual
Page 9
...level of these signals is output from the SPEAKERS R/MONO 1/2 jacks. Y PHANTOM (+48V) switch and indicator This switch turns the phantom power supply on . EMX3000-Owner's Manual Note: The setting of this signal is adjusted by the master MONI 1 fader and the MONO fader. • MONO (BRIDGE) The... specify the signals to be routed to the corresponding jacks according to the power amp section. Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to the speaker connection at the SPEAKER jacks 1 on the rear ...
...level of these signals is output from the SPEAKERS R/MONO 1/2 jacks. Y PHANTOM (+48V) switch and indicator This switch turns the phantom power supply on . EMX3000-Owner's Manual Note: The setting of this signal is adjusted by the master MONI 1 fader and the MONO fader. • MONO (BRIDGE) The... specify the signals to be routed to the corresponding jacks according to the power amp section. Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to the speaker connection at the SPEAKER jacks 1 on the rear ...
Owner's Manual
Page 11
...switch) jack A separately sold Yamaha FC5 foot switch can be sent to switch the built-in power amplifier. The digital effect ON switch on the front panel must be connected to this jack, the corresponding channel of the STEREO bus. EMX3000-Owner's Manual The nominal input level is ... cable to connect to adjust the final level of the signal output from these jacks. The nominal input level is +4 dB. Connect an external mixer output here. THe nominal output level is +4 dB. Use the MONI 1 fader (control panel E) and the MONI 2 fader (control panel F) respectively...
...switch) jack A separately sold Yamaha FC5 foot switch can be sent to switch the built-in power amplifier. The digital effect ON switch on the front panel must be connected to this jack, the corresponding channel of the STEREO bus. EMX3000-Owner's Manual The nominal input level is ... cable to connect to adjust the final level of the signal output from these jacks. The nominal input level is +4 dB. Connect an external mixer output here. THe nominal output level is +4 dB. Use the MONI 1 fader (control panel E) and the MONI 2 fader (control panel F) respectively...
Owner's Manual
Page 21
... PHONE JACK3 PHONE JACK4 PHONE JACK5 1. Balanced. (T=HOT, R=COLD, S=GND) 3. before clip Connectors on mixer ST OUT 1, 2 (L/R) MONO OUT EFFECT SEND MONITOR OUT 1, 2 REC OUT (L/R) CH INSERT OUT (1-4)... mW +4 dB (1.23 V) +20 dB (7.75 V) 300 W/4Ω 600 W/8Ω PHONO JACK PHONE JACK (I /O)4 POWER AMP IN (L, R) +4 dB (1.23 V)5 +18 dB (6.16 V)5 PHONE JACK3 1. Unbalanced. 5. Balanced. (T=HOT, ...0.775 Vrms, 0 dBV is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms. EMX3000-Owner's Manual Impedance balaned. (T=HOT, R=COLD, S=GND) 2. Unbalanced. (T=OUT, R=IN, S=GND) ...
... PHONE JACK3 PHONE JACK4 PHONE JACK5 1. Balanced. (T=HOT, R=COLD, S=GND) 3. before clip Connectors on mixer ST OUT 1, 2 (L/R) MONO OUT EFFECT SEND MONITOR OUT 1, 2 REC OUT (L/R) CH INSERT OUT (1-4)... mW +4 dB (1.23 V) +20 dB (7.75 V) 300 W/4Ω 600 W/8Ω PHONO JACK PHONE JACK (I /O)4 POWER AMP IN (L, R) +4 dB (1.23 V)5 +18 dB (6.16 V)5 PHONE JACK3 1. Unbalanced. 5. Balanced. (T=HOT, ...0.775 Vrms, 0 dBV is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms. EMX3000-Owner's Manual Impedance balaned. (T=HOT, R=COLD, S=GND) 2. Unbalanced. (T=OUT, R=IN, S=GND) ...