Yamaha EMX3000 Support and Manuals
Get Help and Manuals for this Yamaha item
View All Support Options Below
Free Yamaha EMX3000 manuals!
Problems with Yamaha EMX3000?
Ask a Question
Free Yamaha EMX3000 manuals!
Problems with Yamaha EMX3000?
Ask a Question
Popular Yamaha EMX3000 Manual Pages
Owner's Manual - Page 2
... not expressly approved by YAMAHA KEMBLE MUSIC (U.K.) LTD. Follow all installations.
This product, when installed as follows:
The wire which is found in the users manual, may not correspond with the letter L or coloured RED.
* This applies only to products distributed by Yamaha may void your FCC authorization to eliminate the problem by Yamaha Corporation of this product...
Owner's Manual - Page 3
... outlet.
• If you know you for purchasing the Yamaha EMX3000 Powered Mixer. Consult your dealer.
• Do not modify the unit. If you think internal inspection, maintenance, or repair is a potential electrical shock hazard.
• The inside the unit, turn the power switch off , remove the power plug from an AC outlet. Doing so is still...
Owner's Manual - Page 4
... built-in to prevent excessive input levels to small-scale PA systems.
✦A two-channel power amp is output from speaker output jack R, and the monitor signal from the AC outlet. You can connect only one speaker for a
EMX3000-Owner's Manual
much louder sound. ✦In addition to the speaker output jacks, two stereo
output...
Owner's Manual - Page 5
...channel fader.
This means that the peak indicator 3 lights occasionally.
2 A/B switch (Channels 9/10~11/12 only) This switch selects channel 9/10~11/12 input jacks. EMX3000-Owner's Manual...channel. Response is sent to the MONI 2 jack (input/output panel 9). Rotating it toward the left will boost the corresponding frequency band, and rotating it .
If the power...setting of each channel.
Owner's Manual - Page 7
... panel B).
EMX3000-Owner's Manual
Use these switches when you to adjust the level of the signal sent to the speakers.
L PFL (pre-fader listen) switch When this fader does not affect the signal output from the SPEAKER L/ MONI1 1/2 jacks to the SPEAKERS jacks (rear panel 1). If the Power amp select switch V is set to MONO...
Owner's Manual - Page 8
...power amp section reaches the maximum and the limiter is significantly overloaded, which could result in malfunction. EMX3000-Owner's Manual
Note: The master EFFECT fader setting...VOCAL REVERB 3 8 VOCAL REVERB 4
DIGITAL EFFECT
9 HALL 1 10 HALL 2 11 HALL 3 12 ROOM
13 PLATE 1 14 PLATE 2 15 PLATE 3 16 GATE REVERB
O
M MONI 1/2 ...turn the built-in two-channel power amplifier.
This ...
Owner's Manual - Page 9
...setting of this switch is output from the BRIDGE jack. EMX3000-Owner's Manual Set the switch to this signal is set to MONO (BRIDGE), only the L/BRIDGE LEVEL control becomes effective. X POWER... the level of the signals input from the mixer section to the power amp section.
The final level of ...power of the STEREO bus signals is turned on / off for the MIC input jacks for channels...
Owner's Manual - Page 11
... each channel will be connected to this jack. Connect an external mixer or additional PA system to select phone jacks (A) or phono jacks (B). EMX3000-Owner's Manual Use the ST 1 fader (control panel H) to adjust the final output level at the ST 2 jacks.
C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be set...
Owner's Manual - Page 12
... ST1 R bus signals. EMX3000-Owner's Manual
Whichever way the switch is covered by a protective cap to prevent you wish to ST1 L-ST1 R or MONI 1-MONO:
• Two-channel connection You can connect one speaker per channel, use 8~16Ω speakers.
The BRIDGE jack is set to use two speakers per channel.
s When the Power amp select switch is...
Owner's Manual - Page 15
.... EMX3000-Owner's Manual Also make sure that the power of all the way down . Note: You cannot use channel 1~8...channels 1~8) or the 9~12 jacks (channels 9/10~11/12). Basic operation 11
Basic operation
Connecting microphones and instruments
1 Before connecting mics or instruments, make sure that each channel... you set to ST1 L-ST1 R.
2 Connect cables to adjust the tone of each channel fader ...
Owner's Manual - Page 16
... light occasionally. s Playing back a CD player
1 Turn on the CD player.
Use the GAIN control of channel 9/10 so that the 0 LED of using the EMX3000 as a conference or entertainment hall sound system. 12 Example setups
Example setups
This section provides some ways in which the EMX3000 can also be used, and explains connections and operation. EMX3000-Owner's Manual
Owner's Manual - Page 17
... be damaged. Set the Power amp select switch to the effect return signal. If the EFFECT controls are being sent a mix that you use an external effect such as keyboards, to channel input jacks 1~12.
• Connect the main speakers to the SPEAKERS R/ MONO 1/2 jacks, and connect the monitor speakers to the EMX3000's ST SUB...
Owner's Manual - Page 19
...
40
40
40
40
50
50
50
50
50
1
2
3
4
5
6
7
8
9 10
11 12
MONI 1
MONI 2
EFFECT
ST 1
MONO
Yamaha Crossover network PN90
LEFT
TO POWER
INPUTS
AMP INPUTS
RIGHT
HIGH LEFT RIGHT
LOW LEFT RIGHT
ST1 L MONI 1
MONO (BRIDGE)
ST1 R MONO
Power AMP
Subwoofer
EMX3000-Owner's Manual Using a subwoofer
Here is an example of using a subwoofer in the...
Owner's Manual - Page 21
... (I /O)4
POWER AMP IN...mixer
MIC INPUT (1-8) LINE INPUT (1-8) ST INPUT (9-12...set at maximum gain. (All fader and level controls are at maximum position.)
2. Unbalanced. 4. Balanced. (T=HOT, S=COLD) • In these specifications when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms.
EMX3000-Owner's Manual Input specifications...
Owner's Manual - Page 22
Inrush Current: 85A Conformed Environment: E1, E2, E3 and E4
Units: mm
EMX3000-Owner's Manual For European Model Purchaser/User Information specified in EN55103-1 and EN55103-2. 18 Specifications
Dimensions
H: 125
286
D: 454
168
W: 480
Specifications are subject to change without prior notice.
Yamaha EMX3000 Reviews
We have not received any reviews for Yamaha yet.