Owner's Manual
Page 3
... holes at the rear, and the right to amplifier outputs. A damaged power cord is necessary, contact your dealer for purchasing the Yamaha EMX3000 Powered Mixer. Doing so is still connected. Never pull the cord. Using other types of time, such as a wobbly table or slope. - Precautions ..., and unplug the power cable plug from the electrical outlet. • If there is a possibility of this unit, on vacation, EMX3000-Owner's Manual Failure to do not touch the power cable plug if it from the AC outlet, and contact your hearing. • Clean the contacts...
... holes at the rear, and the right to amplifier outputs. A damaged power cord is necessary, contact your dealer for purchasing the Yamaha EMX3000 Powered Mixer. Doing so is still connected. Never pull the cord. Using other types of time, such as a wobbly table or slope. - Precautions ..., and unplug the power cable plug from the electrical outlet. • If there is a possibility of this unit, on vacation, EMX3000-Owner's Manual Failure to do not touch the power cable plug if it from the AC outlet, and contact your hearing. • Clean the contacts...
Owner's Manual
Page 4
...Consult your dealer about replacing defective components. You can connect only one speaker for a EMX3000-Owner's Manual much louder sound. ✦In addition to the speaker output jacks, two stereo output ... and reduced heat generation to 35% or less (in field applications, compared to Yamaha's previous models), and has lead to a reduction in energy cost and to less-restrictive ... not set all equalizer controls and faders to create an unrivaled high-efficiency drive. The mixer also has ample power, with a maximum output of components with mic/line signals. MONO), or...
...Consult your dealer about replacing defective components. You can connect only one speaker for a EMX3000-Owner's Manual much louder sound. ✦In addition to the speaker output jacks, two stereo output ... and reduced heat generation to 35% or less (in field applications, compared to Yamaha's previous models), and has lead to a reduction in energy cost and to less-restrictive ... not set all equalizer controls and faders to create an unrivaled high-efficiency drive. The mixer also has ample power, with a maximum output of components with mic/line signals. MONO), or...
Owner's Manual
Page 9
...three settings to specify the signals to be routed to the corresponding jacks according to the power amp section. EMX3000-Owner's Manual Rotating the knob clockwise will light up when the power of the EMX3000 is connected to the ST 2 jacks (input/ output panel 8). If an external piece of equipment is ...for the MIC input jacks for channels 1~8. Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to the speaker connection at the SPEAKER jacks 1 on the rear panel. • ST1 L-ST1 R The STEREO bus signals are output from ...
...three settings to specify the signals to be routed to the corresponding jacks according to the power amp section. EMX3000-Owner's Manual Rotating the knob clockwise will light up when the power of the EMX3000 is connected to the ST 2 jacks (input/ output panel 8). If an external piece of equipment is ...for the MIC input jacks for channels 1~8. Control panel 5 U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to the speaker connection at the SPEAKER jacks 1 on the rear panel. • ST1 L-ST1 R The STEREO bus signals are output from ...
Owner's Manual
Page 11
... cassette deck, to record the signal from these jacks. EMX3000-Owner's Manual The nominal input level is used to connect stereo outputs of the signals output from the mixer section. Use the ST 1 fader (control panel H) ...1 fader (control panel E) and the MONI 2 fader (control panel F) respectively to adjust the final level of a sub mixer. Use the MONO fader (control panel I) to adjust the final level of a monitor system is +4 dB. 9 MONI...C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be connected to select phone jacks (A) or phono jacks (B).
... cassette deck, to record the signal from these jacks. EMX3000-Owner's Manual The nominal input level is used to connect stereo outputs of the signals output from the mixer section. Use the ST 1 fader (control panel H) ...1 fader (control panel E) and the MONI 2 fader (control panel F) respectively to adjust the final level of a sub mixer. Use the MONO fader (control panel I) to adjust the final level of a monitor system is +4 dB. 9 MONI...C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be connected to select phone jacks (A) or phono jacks (B).
Owner's Manual
Page 21
... gain. (All fader and level controls are at maximum position.) 2. Unbalanced. (T=L, R=R, S=GND) 4. before cliping Connectors on mixer MIC INPUT (1-8) LINE INPUT (1-8) ST INPUT (9-12) ST SUB IN (1, 2) TAPE IN (L, R) MAX MIN MAX MIN...JACK (I /O)2 ST PHONE JACK3 PHONE JACK4 PHONE JACK5 1. Unbalanced. 4. Balanced. (T=HOT, R=COLD, S=GND) 3. before clip Connectors on mixer ST OUT 1, 2 (L/R) MONO OUT EFFECT SEND MONITOR OUT 1, 2 REC OUT (L/R) CH INSERT OUT (1-4) C-R/PHONES for PHONES OUT for C-R...dB is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms. EMX3000-Owner's Manual
... gain. (All fader and level controls are at maximum position.) 2. Unbalanced. (T=L, R=R, S=GND) 4. before cliping Connectors on mixer MIC INPUT (1-8) LINE INPUT (1-8) ST INPUT (9-12) ST SUB IN (1, 2) TAPE IN (L, R) MAX MIN MAX MIN...JACK (I /O)2 ST PHONE JACK3 PHONE JACK4 PHONE JACK5 1. Unbalanced. 4. Balanced. (T=HOT, R=COLD, S=GND) 3. before clip Connectors on mixer ST OUT 1, 2 (L/R) MONO OUT EFFECT SEND MONITOR OUT 1, 2 REC OUT (L/R) CH INSERT OUT (1-4) C-R/PHONES for PHONES OUT for C-R...dB is referenced to 0.775 Vrms, 0 dBV is referenced 1 Vrms. EMX3000-Owner's Manual