Installation Instructions
Page 1
... 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in Rear Wall 7 Attach Mounting Plate to and including 36" (91.4 cm) wide. The appearance of others . These words mean: DANGER You...
... 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Rotate Blower Motor 4 Locate Wall Stud(s 6 Mark Rear Wall 7 Drill Holes in Rear Wall 7 Attach Mounting Plate to and including 36" (91.4 cm) wide. The appearance of others . These words mean: DANGER You...
Installation Instructions
Page 2
... For Wall Venting Installation Only: ■ Cutout must provide: ■ Minimum installation dimensions. Damper assembly (for wall or roof venting) Not Shown: Upper cabinet template Mounting plate (attached to withstand the heat produced by the microwave oven for cooking. See "Venting Design Specifications" section. See "Installation Dimensions" illustration. ■ Minimum one...
... For Wall Venting Installation Only: ■ Cutout must provide: ■ Minimum installation dimensions. Damper assembly (for wall or roof venting) Not Shown: Upper cabinet template Mounting plate (attached to withstand the heat produced by the microwave oven for cooking. See "Venting Design Specifications" section. See "Installation Dimensions" illustration. ■ Minimum one...
Installation Instructions
Page 4
... you are inserted into the microwave oven. Make sure damper plate tabs are using recirculation installation. Damper plate 2. Screws C. If the mounting plate is being handled. 4. Tape the microwave oven door closed so that exhaust ports face the back of microwave oven, and lower blower... the work surface. 1. Slots 8. NOTE: To avoid possible damage to the venting system. Damper plate tabs D. INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be used. Remove any remaining contents from the microwave oven cavity. 2. A B A.
... you are inserted into the microwave oven. Make sure damper plate tabs are using recirculation installation. Damper plate 2. Screws C. If the mounting plate is being handled. 4. Tape the microwave oven door closed so that exhaust ports face the back of microwave oven, and lower blower... the work surface. 1. Slots 8. NOTE: To avoid possible damage to the venting system. Damper plate tabs D. INSTALLATION INSTRUCTIONS Remove Mounting Plate Depending on your model, the mounting plate may be used. Remove any remaining contents from the microwave oven cavity. 2. A B A.
Installation Instructions
Page 6
...Possible Wall Stud Configurations These depictions show examples of each stud, and draw a plumb line down each stud center. End holes (on mounting plate) B. Support tabs F. See illustrations in "Possible Wall Stud Configurations." Wall Stud at One End Hole Figure 3 Wall Studs at... NOTE: If wall stud is within the cabinet opening, do not install the microwave oven. 1. Mounting plate center markers 6 Mark the center of preferred installation configurations with the mounting plate. See illustrations in "Possible Wall Stud Configurations." 2. Wall stud centerlines D. No Wall Studs...
...Possible Wall Stud Configurations These depictions show examples of each stud, and draw a plumb line down each stud center. End holes (on mounting plate) B. Support tabs F. See illustrations in "Possible Wall Stud Configurations." Wall Stud at One End Hole Figure 3 Wall Studs at... NOTE: If wall stud is within the cabinet opening, do not install the microwave oven. 1. Mounting plate center markers 6 Mark the center of preferred installation configurations with the mounting plate. See illustrations in "Possible Wall Stud Configurations." 2. Wall stud centerlines D. No Wall Studs...
Installation Instructions
Page 7
...the cardboard template is aligned to the horizontal line drawn in Step 2 of "Locate Wall Stud(s)," and mark at least 1, preferably 2 hole(s) through the mounting plate, closest to the centerline on the wall, making sure its top is level with the front edge of the cabinet. ■ If the cardboard... in Step 4. Draw the 2 vertical, plumb lines down from the bottom edge of the upper cabinet, and must be on at least 1 wall stud, the mounting plate must attach to figures 1 and 2 in "Possible Wall Stud Configurations" in one 1/4-20 x 3" round-head bolt with front edge of "Mark Rear Wall...
...the cardboard template is aligned to the horizontal line drawn in Step 2 of "Locate Wall Stud(s)," and mark at least 1, preferably 2 hole(s) through the mounting plate, closest to the centerline on the wall, making sure its top is level with the front edge of the cabinet. ■ If the cardboard... in Step 4. Draw the 2 vertical, plumb lines down from the bottom edge of the upper cabinet, and must be on at least 1 wall stud, the mounting plate must attach to figures 1 and 2 in "Possible Wall Stud Configurations" in one 1/4-20 x 3" round-head bolt with front edge of "Mark Rear Wall...
Installation Instructions
Page 8
...the wall at End Holes" in the "Drill Holes in Rear Wall" section. 8 Upper-cabinet template D 10" (25.4 cm) F E 10" G (25.4 cm) Mounting plate C. Check alignment of mounting plate, making sure it is level. 7. Insert lag screws into the wall stud at One End Hole" in the "Drill Holes in Rear... sure toggle nut has opened against the upper cabinet bottom. Push the 2 bolts with toggle nut through the wall and to open . 3. Check alignment of mounting plate, making sure it , trim the template edges so that fits over the 3/4" (19 mm) hole drilled in Step 3 of "Installation for Wall Stud...
...the wall at End Holes" in the "Drill Holes in Rear Wall" section. 8 Upper-cabinet template D 10" (25.4 cm) F E 10" G (25.4 cm) Mounting plate C. Check alignment of mounting plate, making sure it is level. 7. Insert lag screws into the wall stud at One End Hole" in the "Drill Holes in Rear... sure toggle nut has opened against the upper cabinet bottom. Push the 2 bolts with toggle nut through the wall and to open . 3. Check alignment of mounting plate, making sure it , trim the template edges so that fits over the 3/4" (19 mm) hole drilled in Step 3 of "Installation for Wall Stud...
Installation Instructions
Page 9
... more people, lift microwave oven and hang it on the template. Failure to move and install microwave oven. A. Damper blade D. Sheet metal screws 3. Mounting plate B. Rotate microwave oven up toward upper cabinet. NOTE: If upper cabinet is for the power supply cord. B A A. Metal cabinet B. These... used to secure the microwave oven to the microwave oven, do so can result in place. 9 Support tabs 4. Push microwave oven against mounting plate and hold in back or other injury. Handle the microwave oven gently. 1. Back of the microwave oven is at one corner of ...
... more people, lift microwave oven and hang it on the template. Failure to move and install microwave oven. A. Damper blade D. Sheet metal screws 3. Mounting plate B. Rotate microwave oven up toward upper cabinet. NOTE: If upper cabinet is for the power supply cord. B A A. Metal cabinet B. These... used to secure the microwave oven to the microwave oven, do so can result in place. 9 Support tabs 4. Push microwave oven against mounting plate and hold in back or other injury. Handle the microwave oven gently. 1. Back of the microwave oven is at one corner of ...
Installation Instructions
Page 10
...household fuse has not blown, or that the power supply cord is no gap between the upper cabinet bottom and the microwave oven. Adjust mounting plate and retighten screws. 9. NOTES: ■ Some upper cabinets may warp the top of the damper assembly slides under vent) Complete Installation...same thickness as shown. Raised tabs B. If the problem continues, call an electrician. ■ Check that a circuit breaker has not tripped. Loosen mounting plate screws. Longer or shorter bolts are available at least one person holding it in death, fire, or electrical shock. 2. Long tab F. ...
...household fuse has not blown, or that the power supply cord is no gap between the upper cabinet bottom and the microwave oven. Adjust mounting plate and retighten screws. 9. NOTES: ■ Some upper cabinets may warp the top of the damper assembly slides under vent) Complete Installation...same thickness as shown. Raised tabs B. If the problem continues, call an electrician. ■ Check that a circuit breaker has not tripped. Loosen mounting plate screws. Longer or shorter bolts are available at least one person holding it in death, fire, or electrical shock. 2. Long tab F. ...
Installation Instructions
Page 12
... to round transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m) If the existing vent is located behind the door. ■ Damper Assembly ■ Mounting Plate ■ Upper Cabinet Template ■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the system. You will need , add the equivalent lengths of the microwave oven. Recommended...
... to round transition piece = 5 ft (1.5 m) D. 2 ft (0.6 m) + 6 ft (1.8 m) straight = 8 ft (2.4 m) If the existing vent is located behind the door. ■ Damper Assembly ■ Mounting Plate ■ Upper Cabinet Template ■ Mounting Screw Kit (includes parts A-G in "Parts Supplied" in the system. You will need , add the equivalent lengths of the microwave oven. Recommended...
Owners Manual
Page 2
... plug in water. ■ Keep cord away from heated surfaces. ■ Do not let cord hang over edge of table or counter. ■ Do not mount over a sink. ■ Do not cover racks or any other than manufacturer's recommended accessories, in this oven with the safety interlocks. (b) Do not place any...
... plug in water. ■ Keep cord away from heated surfaces. ■ Do not let cord hang over edge of table or counter. ■ Do not mount over a sink. ■ Do not cover racks or any other than manufacturer's recommended accessories, in this oven with the safety interlocks. (b) Do not place any...