Whirlpool WGD8740DW Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WGD8740DW manuals!
Problems with Whirlpool WGD8740DW?
Ask a Question
Free Whirlpool WGD8740DW manuals!
Problems with Whirlpool WGD8740DW?
Ask a Question
Popular Whirlpool WGD8740DW Manual Pages
Dimension Guide - Page 2
... be used. An individual manual shutoff valve must be 1/2" IPS. Damage to L.P. Rigid or flexible metal exhaust vent must be in accordance with the National Fuel Gas Code ANSI Z223.1.
Dimensions are recommended. Specifications subject to the gas supplier and local codes, 3/8" approved tubing may be installed within 6 ft (1.8 m) of the dryer in the path of...
Installation Guide - Page 5
... bottom of dryer.
■■The dryer must support dryer weight of dryer.
measurement
61/4" (159 mm)
Vent
Water inlet
(Steam Models Only)
297/8"* (759 mm)
31/2"* (89 mm)
Gas
3/4"* (18 mm)
143/8" (365 mm)
253/4" (654 mm)
61/8"* (156 mm)
* Approx. See "Venting Requirements."
5 If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number...
Installation Guide - Page 7
...a quali ed electrician or service representative or personnel if you use with a different gas without consulting your gas company.
7 LP Gas Conversion:
IMPORTANT: Conversion must be grounded. SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
I For a grounded, cord-connected dryer: This dryer must be made by CSA International for use Power Supply Cord Replacement Part Number 8529008. In the...
Installation Guide - Page 8
... than 1/2 psi.
In Canada: An individual manual shut-off valve must be installed within six (6) ft. (1.8 m) of the...installed above 2,000 ft. (610 m) a 4% reduction of E.I. E C
A
11/2" (38 mm)
*53/4" (146 mm)
3/8" NPT dryer gas pipe
* NOTE: If the dryer is a registered trademark of the
burner Btu rating shown on the pedestal model. Gas shut-off valve be connected to the dryer...
Use & Care Guide - Page 5
... venting will be sure to follow the Installation Instructions supplied with your dryer for getting the best performance from your steam dryer (on some models)
n Results may require additional touching up after cycles that uses steam.
Wash any starched or new garments prior to efficiently dry laundry. Service calls caused by improper venting are sensed in...
Use & Care Guide - Page 7
...Guide").
For more information on each cycle. Temp When using Manual Cycles or Steam Refresh, you select a cycle, its settings will be displayed. Dryness Level When using a slightly lower heat level.
The Steam Cycle (on some models...vary across loads and cycles. Follow garment label instructions. When selected, a series of the dryer and avoid an accidental change in process. ...
Use & Care Guide - Page 8
Cycle Guide - Not all features and cycles are default settings for enhanced fabric care and energy savings.
do not overfill dryer drum. Offers stepped drying starting with High and Medium Drying Temperature settings.
* On steam models only. Use for improved moisture removal and enhanced fabric care.
† On some models, you may select the "With Steam" setting to...
Use & Care Guide - Page 9
.... Steam Cycle (steam models only)
Settings and options shown in 1-minute increments. Small load: Fill the dryer drum with High and Medium Drying Temperature settings. If there is available only with 3-4 items, not more than the higher setting.
† On some knits.
Line dry bonded or laminated fabrics.
Cycle Guide - Do not add dryer sheets.
† You...
Use & Care Guide - Page 11
... hold to begin cycle
Appearance may adjust different settings, depending on some models): Select Steam Refresh to adjust the default settings. 1. 5. See the "Cycle Guide" for the selected cycle. Drying time can be changed after first pausing the cycle. Manual Cycles: When you have selected an Automatic Cycle, Manual Cycle, or Steam Cycle (on whether you...
Use & Care Guide - Page 12
...dryer, order by calling 1-877-944-7566. Remove and discard any lint accumulated from the dryer. Rest the rear support... removed. See "Troubleshooting" section.
NOTE: Static Reduce is not available on all indicators are other error issues during a ...setting. 6. NOTE: Steam is not available on all models. The drying rack cannot be removed from items dried on the front of the dryer...
Use & Care Guide - Page 15
...a service call an electrician. Run the dryer for 5-10 minutes.
Lint screen is blocked. For optimal dry times, turn on some models)
...replace exhaust vent with Steam cycle selected (on the EcoBoost™ option. If the problem continues, call .
This is on the drum rollers. See the Installation Instructions. Separate the load items and restart the dryer. Run the dryer...
Use & Care Guide - Page 16
... care label instructions. Steam models only: Make sure water is not too long or has too many turns.
The dryer is clogged with damp or wet spots. The Air Only temperature setting has been selected. The load is best for most installations, the rear of the dryer requires 5" (127 mm).
See the Installation Instructions. See "Level Dryer" in a closet...
Use & Care Guide - Page 17
... cycle, and restart the dryer. variable service codes
If a code beginning with your home power supply, keeping the dryer's heater from the dryer to avoid overdrying the load.
Using Timed Dry cycle with a lower heat setting to the wall is free of service. "L2" Diagnostic Code (low or no line voltage condition)
There may be a problem with an "F" appears in...
Use & Care Guide - Page 18
... to correct improper product maintenance or installation, installation not in -home repair. 11. Consumable parts (i.e. This product is not available. 12. Travel or transportation expenses for service in remote locations where an authorized Whirlpool servicer is intended for in
accordance with published user, operator, or installation instructions.
2. trim, decorative panels, flooring...
Warranty Information - Page 1
... 10. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Please have other rights that interfere with servicing, removal, or replacement of God, or use with electrical or plumbing codes, or correction of your retailer about the quality, durability, or need for Factory Specified Replacement Parts and repair labor to review the Troubleshooting or Problem Solver section...
Whirlpool WGD8740DW Reviews
We have not received any reviews for Whirlpool yet.