Whirlpool WED94HEXR Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED94HEXR manuals!
Problems with Whirlpool WED94HEXR?
Ask a Question
Free Whirlpool WED94HEXR manuals!
Problems with Whirlpool WED94HEXR?
Ask a Question
Most Recent Whirlpool WED94HEXR Questions
Serial Number Location?
Where is the serial number on the WED94HEXR washer and dryer?
Where is the serial number on the WED94HEXR washer and dryer?
(Posted by juliamerryhiatt 12 years ago)
How Does The Door Open; Hinges On The Left Or On The Right?
can the swing be reversed?
can the swing be reversed?
(Posted by ggemgnani 12 years ago)
Popular Whirlpool WED94HEXR Manual Pages
Dimension Guide - Page 1
... breaker is required.
W10057363B 12/2010 Electric Dryer Installation Instructions
PRODUCT MODEL NUMBERS
WED94HEX, WED95HEX, WED97HEX, WEDXXHEX
Electrical: This dryer requires a 3 or 4 wire, single ...Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to the cold water faucet using new inlet hoses. Exhaust venting: Exhaust your dryer...
Installation Instructions - Page 1
SP
1 ELECTRIC DRYER INSTALLATION INSTRUCTIONS
Para una version de estas instrucciones en español, visite www.Whirlpool.com
Table of Contents
DRYER SAFETY 2 Installation Requirements 3
Tools and Parts 3 Location Requirements 4 Electrical Requirements 4 INSTALL LEVELING LEGS 6 ELECTRICAL INSTALLATION 7
Power Supply Cord Connection 8 Direct Wire Connection 10 VENTING 13 Venting ...
Installation Instructions - Page 4
... consider weight of companion appliance.
■■Cold water faucets located within 2 ft. (610 mm) of either side of 5" (127 mm) clearance behind dryer for proper exhaust installation.
See "Venting Requirements."
Some codes limit, or do not permit, installation of 20 - 120 psi (138 - 827 kPa). Some codes limit, or do not permit, installing dryer in an area where...
Installation Instructions - Page 13
...governing codes and...Replace plastic or metal foil vents with screws or other fastening devices that may result in reduced airflow and poor performance.
■■ Do not install...Review Vent System Chart and if necessary, modify existing vent system to avoid crushing and kinking. Do not use an exhaust hood with lint. Dryer exhaust must not be fully extended and supported in final dryer...
Installation Instructions - Page 18
...
18 q Check for certain part replacement or repair. q Read "Dryer Use" in your tools.
q Check that dryer is first heated. q Wipe dryer drum interior thoroughly with a damp cloth to see what was skipped.
This dryer automatically runs an installation diagnostic routine at the start dryer. q Dispose of your Use and Care Guide. q Be sure the water faucets are on Power. q For...
Owners Manual - Page 5
... dryer. Under certain environmental or installation conditions, you may vary depending on clothes. Service calls caused by improper venting are sensed in the dryer too long. With Timed Dry, the dryer ...n Use of vent possible. n On some models, the Quick Refresh Cycle time is set and sometimes results in good air flow. See Installation Instructions. n It is best for smoothing out wrinkles...
Owners Manual - Page 9
... tumble freely.
9 Not all models.
Steam cycles are available on 8-cycle models. † Or Wrinkle Shield with dry loads to a damp level for that cycle. CYCLE GUIDE - Do not add dryer sheets
* 12 minutes on 11-cycle models. 15 minutes on each cycle. PreOss and hold to Medium heat setting may be manually adjusted, but Temperature is...
Owners Manual - Page 11
... select a Manual Cycle, the default time appears in the time display: 01, 02, or 03.
3. For models without stopping the cycle. There are consistently not as dry as Static Reduce, Wrinkle Shield/ Wrinkle Shield with Steam
Extra Low oNportmioalnDrybe2fo- 3re preSsosfting START/PAUSE. The dryer must be changed while the dryer is set the drying...
Owners Manual - Page 12
...models or on all cycles. NOTE: Static Reduce is operating. ADDITIONAL FEATURES
USING THE DRYING RACK
To obtain a drying rack for your dryer, follow the instructions included in the cycle by using the Air Only setting. 6. Remove and discard any lint accumulated from the dryer... rack with the Manual Dry/ Timed Dry... Open dryer door.
2. Rest the rear support on the front of the dryer drum...
Owners Manual - Page 14
... of hose failure. Steam models only: Shut off water faucet. 6. Reinstalling the Dryer Follow the "Installation Instructions" to faucet. Clean lint screen. Unplug the power supply cord. 2.
Reconnect water inlet hose to locate, level, and connect the dryer.
14 Use tape to a water pressure surge) while you should: 1. When replacing your dryer. Disconnect power. 2. To Winterize...
Owners Manual - Page 15
... tight, or that the exhaust vent is closed completely. The dryer is clogged with Steam cycle selected
Thumping noise
Water pump on dryer is blown or circuit breaker has tripped. The Air Only temperature setting has been selected.
Clean lint screen before laundering. See the Installation Instructions. Use 4" (102 mm) diameter vent material.
START/PAUSE button...
Owners Manual - Page 16
...) of airspace, and, for reducing wrinkles and odors from dryer at the top and bottom of the door. See the Installation Instructions. The cycle time will not transfer to dry quickly. For steam cycles, the water is clogged with the dryer.
NOTE: Refer to tumble freely. TROUBLESHOOTING
First try the solutions suggested here or visit our...
Owners Manual - Page 17
... the dryer to the Installation Instructions for details. Replace the fuse or reset the circuit breaker.
Try the following :
Check to see if the vent run cleaned.
Call for service.
17
Make sure water is connected to the dryer. Check that requires service.
Try the following :
• Clean lint screen.
• Check to run when this diagnostic code is...
Owners Manual - Page 18
... "Troubleshooting" section of the Use & Care Guide.
Replacement parts or repair labor if this major appliance is used in a manner that is intended to instruct you also may not apply to published user or operator instructions and/or installation instructions.
2. Consumable parts are unable to the nish of your major appliance is located in a remote area where service by a Whirlpool...
Warranty - Page 1
... is not installed in accordance with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will need to correct defects in your major appliance if it was purchased. If you think you ever need repair service, rst see the "Troubleshooting" section of purchase.
6. You will pay for Factory Speci ed Parts and repair labor to know your complete model number...
Whirlpool WED94HEXR Reviews
We have not received any reviews for Whirlpool yet.