Installation Instructions
Page 3
The cord should contain: ■■A UL listed 30-amp power supply cord, rated 120/240 volt minimum. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with dryer) Refer to your Use and Care Guide for information about accessories available for door reversal only) ® TORX is ...
The cord should contain: ■■A UL listed 30-amp power supply cord, rated 120/240 volt minimum. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with dryer) Refer to your Use and Care Guide for information about accessories available for door reversal only) ® TORX is ...
Installation Instructions
Page 4
... where it will need : ■■A location allowing for ease of dryer to water and/or weather. measurement. LOCATION REQUIREMENTS Check code requirements. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of dryer. ■■The dryer must...
... where it will need : ■■A location allowing for ease of dryer to water and/or weather. measurement. LOCATION REQUIREMENTS Check code requirements. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of dryer. ■■The dryer must...
Installation Instructions
Page 15
...replace hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. See figure A. Screw on coupling by hand until it is in the "Y" connector. Vent must be connected to seal ... (305 mm) Install exhaust hood and use to reduce the risk of the "Y" connector to dryer location using the new inlet hoses. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. NOTE: Replace inlet hoses after 5 years of the short hose. Run vent to the cold...
...replace hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose, and replace rubber washer Turn cold water faucet off and remove washer inlet hose. See figure A. Screw on coupling by hand until it is in the "Y" connector. Vent must be connected to seal ... (305 mm) Install exhaust hood and use to reduce the risk of the "Y" connector to dryer location using the new inlet hoses. Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. NOTE: Replace inlet hoses after 5 years of the short hose. Run vent to the cold...
Installation Instructions
Page 16
... hoses. 16 Attach other side of dryer back panel. Attach this end to "Y" connector and tighten couplings Remove protective cap from water inlet valve. Attach washer cold inlet hose to the coupling can result. 6. Using pliers, tighten the couplings an additional two-thirds turn . Turn on . 7. Screw on coupling by hand...
... hoses. 16 Attach other side of dryer back panel. Attach this end to "Y" connector and tighten couplings Remove protective cap from water inlet valve. Attach washer cold inlet hose to the coupling can result. 6. Using pliers, tighten the couplings an additional two-thirds turn . Turn on . 7. Screw on coupling by hand...
Owners Manual
Page 4
..., call 1-800-901-2042, or visit us at : www.whirlpool.com/accessories. Available in matching colors. The large drawer provides convenient storage. Stack Kit If space is at a premium, the stack kit allows the dryer to a more information on top of the washer. 4 whirlpoolparts.ca 15" Pedestal Color matched pedestals raise the...
..., call 1-800-901-2042, or visit us at : www.whirlpool.com/accessories. Available in matching colors. The large drawer provides convenient storage. Stack Kit If space is at a premium, the stack kit allows the dryer to a more information on top of the washer. 4 whirlpoolparts.ca 15" Pedestal Color matched pedestals raise the...