Whirlpool WED94HEAW Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED94HEAW manuals!
Problems with Whirlpool WED94HEAW?
Ask a Question
Free Whirlpool WED94HEAW manuals!
Problems with Whirlpool WED94HEAW?
Ask a Question
Whirlpool WED94HEAW Videos
Duet Electric Steam Dryer WED94HEAW: Whirlpool at Abt Electronics
Duration: 1:32
Total Views: 1,711
Duration: 1:32
Total Views: 1,711
Popular Whirlpool WED94HEAW Manual Pages
Ventilation Specification - Page 1
... supplier. W10100920D DRYER VENTING SPECIFICATIONS
Table of Contents
DRYER SAFETY...1 INSTALLATION REQUIREMENTS ...4
Venting Requirements ...5 DRYER INSPECTION AND CLEANING 7
Frequency of Exhaust System Cleaning 7 Inspecting the Exhaust System ...7
DRYER SAFETY
■ If you are installing a gas dryer, it is recommended that the owner post, in a prominent location, instructions for the customer...
Ventilation Specification - Page 4
... Whirlpool dryers must meet codes requirements.
2. Lint Even though the dryer is generated to vaporize the water.
These dampers may also apply to multi-dryer vent systems.
There are other codes requiring dryers to be met. Codes Requirements The following codes should be used or considered for spacing requirements. See the Installation Instructions for the specific dryer model...
Ventilation Specification - Page 5
...Codes Agency Approvals
All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that have an inlet and outlet for each model, or on the Whirlpool...following illustration. Each dryer model has a maximum rated vent length, shown in which the Installation Instructions do not address the vent length for the specific number of elbows ...
Use & Care Guide - Page 7
... models) Touch to activate the Steam option, which allows you to increase your dryer.
Follow garment label instructions. When selected, a series of beeps will sound when the load is selected as a default for the Bulky cycle, as a reminder to manually reposition bulky loads midway through the cycle.
This option adds approximately 8 minutes to adjust settings...
Use & Care Guide - Page 9
CYCLE GUIDE - MANUAL CYCLES
Settings and options shown in bold are default settings for each cycle.
This is available only with 3-4 items, not more than the higher setting.
† You ...cycle after 60 minutes.
Not all models. Select a drying temperature based on each cycle. A Low to Medium heat setting may select the "With Steam" setting to select for drying medium-weight...
Use & Care Guide - Page 11
... in the shortest time. Your automatic drying settings can select a different dryness level, depending on your loads on some models) by pressing Temp until the desired dry temperature is off . See the "Cycle Guide" for 6 seconds. 2. Once a dryness level is set, it cannot be changed while the dryer is finished
Promptly remove garments after cycle...
Use & Care Guide - Page 12
... ended and the load may be dried on some models) This indicator will light to circulate. Close the door. 5. Start the dryer. For more information on all cycles.
Wrinkle Shield™ Option This indicator will light when a Manual Cycle has been selected. Rest the rear support on the front of the cycle, the Check Vent...
Use & Care Guide - Page 15
... . This is not the correct size. Run the dryer for assistance and to check air movement. See the Installation Instructions. The exhaust vent or outside exhaust hood to possibly avoid a service call. When balled up in the Installation Instructions.
If the problem continues, call an electrician.
If the problem continues, call an electrician.
Hold your hand under the...
Use & Care Guide - Page 17
... at www.whirlpool.com/product_help - Check that requires service.
variable service codes.
Check that the power cord is connected to the dryer.
Replace the fuse or reset the circuit breaker. If the message persists, consult a qualified electrician. If a code beginning with an "F" appears in need of lint and debris.
Confirm that water inlet hose is properly installed...
Installation Guide - Page 1
... 12 Plan Vent System 13 Install Vent System 14 CONNECT INLET HOSE (STEAM MODEL ONLY 15 CONNECT VENT 16 LEVEL DRYER 17 COMPLETE INSTALLATION CHECKLIST 17 DOOR REVERSAL (OPTIONAL 17
Para una version de estas instrucciones en español, visite www.Whirlpool.com
INSTALLATION NOTES Date of purchase Date of installation Installer Model number Serial number
W10508904B W10508905B...
Installation Guide - Page 5
... (1) new branch-circuit installations after 1996, and all local codes and ordinances.
The kit should contain:
■■A UL listed 30-amp power supply cord, rated 120/240 volt minimum. Electrical Connection
To properly install your "Use and Care Guide." ■■Special provisions must conform to introduce outside air into dryer. The green ground wire...
Installation Guide - Page 17
... is first heated. q For power supply cord installation, plug into an outlet and/or electrical
supply. • Household fuse is intact and tight, or circuit breaker
has not tripped. • Dryer door is recommended to adjust legs up or down, and check again for certain part replacement or repair. NOTE: You may notice an odor when...
Installation Guide - Page 18
... strike
Min. 8" long TORX® † T25 screwdriver
#2 Phillips screwdriver
Reverse door swing round-shaped door - Lift off the inner door and set aside.
† ® TORX is a registered trademark of the dryer. DOOR REVERSAL (OPTIONAL)
The following instructions are for models with the inside of dryer door frame, as shown.
3.
Rotate the strike 180° and attach to the...
Installation Guide - Page 21
... facing up and out to the outer door.
10. Place the door on the dryer. Reinstall inner door assembly
Bottom of the dryer. Remove door from the dryer door before proceeding. Using a TORX T25 screwdriver, remove the 2 screws securing the door strike to the door frame of door
Reverse door swing round-shaped door - Move the door strike
Using a TORX® T25 screwdriver, remove...
Dimension Guide - Page 2
...Review "Vent System Chart" and if necessary, modify existing vent system to the chart.
For complete details, see Installation Instructions packed with rigid metal or flexible metal vents. A time-delay fuse or circuit breaker is required. WATER (STEAM MODELS ONLY) REQUIREMENTS
The dryer...and specifications ... Exhaust your dryer to change without notice. Because Whirlpool Corporation policy ...
Whirlpool WED94HEAW Reviews
We have not received any reviews for Whirlpool yet.