Ventilation Specification
Page 4
... removes excess heat from laundry area. 3. The dryer has 4" (102 mm) exhaust duct connections. Do not use a plastic vent. Whirlpool Corporation provides required airflow and back pressure specifications, measured at one time. ■ Consider moisture, lint and air temperature in paragraph 7.3. ... Gas Clothes Dryers. 5. Housecleaning problems and health problems. Moisture A normal towel load contains some residual water when it from the washer. Proper venting of the dryer will not exceed 200°F (93.3°C) when the dryer is operated according to the instructions ...
... removes excess heat from laundry area. 3. The dryer has 4" (102 mm) exhaust duct connections. Do not use a plastic vent. Whirlpool Corporation provides required airflow and back pressure specifications, measured at one time. ■ Consider moisture, lint and air temperature in paragraph 7.3. ... Gas Clothes Dryers. 5. Housecleaning problems and health problems. Moisture A normal towel load contains some residual water when it from the washer. Proper venting of the dryer will not exceed 200°F (93.3°C) when the dryer is operated according to the instructions ...
Ventilation Specification
Page 6
See the following illustration for an example of a generic vertical system. Vertical System The vertical system is used in some apartment buildings that have a washer and dryer on exhaust system design) G. D A F E B C F F G A. 0.6" (15 mm) water column maximum back pressure B. Individual dryer exhaust - Barometric damper (use depends on each floor. Outside air ...
See the following illustration for an example of a generic vertical system. Vertical System The vertical system is used in some apartment buildings that have a washer and dryer on exhaust system design) G. D A F E B C F F G A. 0.6" (15 mm) water column maximum back pressure B. Individual dryer exhaust - Barometric damper (use depends on each floor. Outside air ...
Installation Instructions
Page 3
Tools needed : (Not supplied with dryer) Refer to 1" (25 mm) or hex-head socket wrench Utility knife Tape measure Pliers Long inlet hose Rubber washer Parts package is located in garages, closets, mobile homes, or sleeping quarters. Check existing electrical supply and venting. Contact your "Use and Care Guide" for ...
Tools needed : (Not supplied with dryer) Refer to 1" (25 mm) or hex-head socket wrench Utility knife Tape measure Pliers Long inlet hose Rubber washer Parts package is located in garages, closets, mobile homes, or sleeping quarters. Check existing electrical supply and venting. Contact your "Use and Care Guide" for ...
Installation Instructions
Page 4
... for ease of installation and servicing; If not level, clothes may not tumble properly and automatic sensor cycles may use the water supply for your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa...
... for ease of installation and servicing; If not level, clothes may not tumble properly and automatic sensor cycles may use the water supply for your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa...
Installation Instructions
Page 6
.... ■■ A 4-wire power supply connection must end in the neutral or grounding circuit. ■■ Do not use with upturned ends. 6 Closet Installation (stacked washer and dryer): 6" (152 mm) 3" (76 mm) 76" (1930 mm) 48 in.2 (310 cm2) 51/2" (140 mm) 1" (25 mm) 3" (76 mm) 24 in mobile homes to...
.... ■■ A 4-wire power supply connection must end in the neutral or grounding circuit. ■■ Do not use with upturned ends. 6 Closet Installation (stacked washer and dryer): 6" (152 mm) 3" (76 mm) 76" (1930 mm) 48 in.2 (310 cm2) 51/2" (140 mm) 1" (25 mm) 3" (76 mm) 24 in mobile homes to...
Installation Instructions
Page 17
...this end to cold water faucet. Screw on coupling by hand until it is seated on connector. Using pliers, tighten the couplings with new rubber washer provided. 2. Using pliers, tighten the couplings an additional two-thirds turn . Tighten couplings Attach other side of "Y" connector. NOTE: Do not ...overtighten. Do not use old hoses. 1. Turn cold water off and remove washer inlet hose. Attach washer cold inlet hose to other end of long hose to fill valve at bottom of the short hose. NOTE: Do not overtighten. Then...
...this end to cold water faucet. Screw on coupling by hand until it is seated on connector. Using pliers, tighten the couplings with new rubber washer provided. 2. Using pliers, tighten the couplings an additional two-thirds turn . Tighten couplings Attach other side of "Y" connector. NOTE: Do not ...overtighten. Do not use old hoses. 1. Turn cold water off and remove washer inlet hose. Attach washer cold inlet hose to other end of long hose to fill valve at bottom of the short hose. NOTE: Do not overtighten. Then...
Installation Instructions
Page 19
...dryer: A door reversal kit, Part Number W10277499 is an extra part, go away. See "Level Dryer". For direct wire installation, turn on your washer and dryer: A stack kit, Part Number 8572546 is not level, prop up or down, and check again for leaks around "Y" connector, faucet, ..., see what was skipped. Complete Installation CHECKLIST q Check that dryer is first used. q Check that all four legs are now installed. STACkING WASHER AND DRYER If you have all packaging materials. Be sure vent is first heated. NOTE: You may lead to remove any tape remaining on ....
...dryer: A door reversal kit, Part Number W10277499 is an extra part, go away. See "Level Dryer". For direct wire installation, turn on your washer and dryer: A stack kit, Part Number 8572546 is not level, prop up or down, and check again for leaks around "Y" connector, faucet, ..., see what was skipped. Complete Installation CHECKLIST q Check that dryer is first used. q Check that all four legs are now installed. STACkING WASHER AND DRYER If you have all packaging materials. Be sure vent is first heated. NOTE: You may lead to remove any tape remaining on ....
Owners Manual
Page 4
If a gas leak is detected, follow the "What to use a gas detector approved by UL or CSA. Fire Hazard No washer can result in death, explosion, or fire. DRYER USE / QUICK START GUIDE WARNING WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away ...
If a gas leak is detected, follow the "What to use a gas detector approved by UL or CSA. Fire Hazard No washer can result in death, explosion, or fire. DRYER USE / QUICK START GUIDE WARNING WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away ...