Dimension Guide
Page 1
...view) 3/8" (9.5 mm) 1" 18 21/32" (25.4 mm) (47.4 cm) NOTE: Access panel is available from water inlet valve. Because Whirlpool Corporation policy includes a continuous commitment to water inlet valve. Water: A hot water line with product. Use 1/2" minimum I.D. door closed side view ạ door pivot door opened access ...measured from narrowest point of opening in shaded areas makes connection easier. Cut door panel to waste tee or disposer inlet above drain trap in open position ạ. Use 3/8" O.D. Connect drain hose to clear access panel when door is recommended. Use...
...view) 3/8" (9.5 mm) 1" 18 21/32" (25.4 mm) (47.4 cm) NOTE: Access panel is available from water inlet valve. Because Whirlpool Corporation policy includes a continuous commitment to water inlet valve. Water: A hot water line with product. Use 1/2" minimum I.D. door closed side view ạ door pivot door opened access ...measured from narrowest point of opening in shaded areas makes connection easier. Cut door panel to waste tee or disposer inlet above drain trap in open position ạ. Use 3/8" O.D. Connect drain hose to clear access panel when door is recommended. Use...
Installation Instructions
Page 5
... connectors. - If this is not long enough, use a new drain hose with all current AHAM/IAPMO test standards, is connected to the underside of water inlet valve. Water Supply Requirements ■ A hot water line with dishwashers. We recommend: ■ A time-delay fuse or circuit breaker. ■ A separate circuit. ...air gap if the drain hose is resistant to heat and detergent, and fits the 1" ■ Connect drain hose to waste tee or disposer inlet above drain trap in the cabinet next to 862 kPa) water pressure. ■ 120°F (49°C) water at dishwasher O.D. Part ...
... connectors. - If this is not long enough, use a new drain hose with all current AHAM/IAPMO test standards, is connected to the underside of water inlet valve. Water Supply Requirements ■ A hot water line with dishwashers. We recommend: ■ A time-delay fuse or circuit breaker. ■ A separate circuit. ...air gap if the drain hose is resistant to heat and detergent, and fits the 1" ■ Connect drain hose to waste tee or disposer inlet above drain trap in the cabinet next to 862 kPa) water pressure. ■ 120°F (49°C) water at dishwasher O.D. Part ...
Installation Instructions
Page 8
...passes through hole cut , use a new drain hose. 1. Turn shutoff valve to "ON" position. with air gap: 1. with air gap ■ Option 2, No waste disposer - or screw-type clamps Air gap Large spring-type clamp Drain trap Disposer inlet Drain hose 4. Option 2, Power supply cord method: NOTE: A mating,... Drill a minimum ¹⁄₂" (1.3 cm) hole in the cabinet rear or side. Measure overall length of particles that may clog the inlet valve. 6. Connect drain hose to the sink. 2. If the drain hose was cut in cabinet wall or floor on the front left side of...
...passes through hole cut , use a new drain hose. 1. Turn shutoff valve to "ON" position. with air gap: 1. with air gap ■ Option 2, No waste disposer - or screw-type clamps Air gap Large spring-type clamp Drain trap Disposer inlet Drain hose 4. Option 2, Power supply cord method: NOTE: A mating,... Drill a minimum ¹⁄₂" (1.3 cm) hole in the cabinet rear or side. Measure overall length of particles that may clog the inlet valve. 6. Connect drain hose to the sink. 2. If the drain hose was cut in cabinet wall or floor on the front left side of...