English Manual
Page 4
... of the way when performing squat exercises. 17. Make sure all instructions in any worn parts immediately. 6. Keep hands and feet away from the weight rack when performing an exercise that the cables remain on the weight rests. Replace all cables at all users of the weight bench are exercising, stop...
... of the way when performing squat exercises. 17. Make sure all instructions in any worn parts immediately. 6. Keep hands and feet away from the weight rack when performing an exercise that the cables remain on the weight rests. Replace all cables at all users of the weight bench are exercising, stop...
English Manual
Page 7
... (32) and two M10 Nylon Locknuts (34). 2. Attach the Left Front Upright (44) to the Left Base (40) 2 with four M10 x 78mm Bolts (32), two Rack Joint Plates (85), and two M10 Nylon Locknuts (34). Note: The Rear Uprights are on the Right Front Upright (not shown). Repeat this step with...
... (32) and two M10 Nylon Locknuts (34). 2. Attach the Left Front Upright (44) to the Left Base (40) 2 with four M10 x 78mm Bolts (32), two Rack Joint Plates (85), and two M10 Nylon Locknuts (34). Note: The Rear Uprights are on the Right Front Upright (not shown). Repeat this step with...
English Manual
Page 24
If there is first used on the accompanying exercise guide. SETTING UP FOR SQUAT EXERCISES Squat exercises should be performed inside the rack (behind the dotted line in the cables, tighten them by turning the Adjustment Knobs (22) counterclockwise until they are fully tightened. The ...51) to the two Pulley Plates (82). The selected holes for lifting and replacing the barbell. Perform the exercise as shown on the weight rack, can stretch slightly after it is slack in the picture). When performing squat exercises, set of holes in the Uprights and turn the Knobs clockwise...
If there is first used on the accompanying exercise guide. SETTING UP FOR SQUAT EXERCISES Squat exercises should be performed inside the rack (behind the dotted line in the cables, tighten them by turning the Adjustment Knobs (22) counterclockwise until they are fully tightened. The ...51) to the two Pulley Plates (82). The selected holes for lifting and replacing the barbell. Perform the exercise as shown on the weight rack, can stretch slightly after it is slack in the picture). When performing squat exercises, set of holes in the Uprights and turn the Knobs clockwise...
English Manual
Page 25
... (31) Length: 1.74m 5 4 3 3 5 3 Long Cable (68) Length: 5.57m 1 2 6 4 23 Make sure that the cables and the cable traps have not been correctly routed, the weight rack will not function properly and damage may occur. If the cables have been assembled correctly. Use the diagram to make sure that the cable traps...
... (31) Length: 1.74m 5 4 3 3 5 3 Long Cable (68) Length: 5.57m 1 2 6 4 23 Make sure that the cables and the cable traps have not been correctly routed, the weight rack will not function properly and damage may occur. If the cables have been assembled correctly. Use the diagram to make sure that the cable traps...
English Manual
Page 30
... M8 x 58mm Bolt Weight Tube M10 x 58mm Carriage Bolt M6 Washer Plastic Butterfly Bushing Butterfly Cap Double "U"-bracket Pulley Plate Carriage Stop Bushing Square Bushing Rack Joint Plate "V"-pulley Pulley Cable Trap 17mm Spacer M10 x 75mm Carriage Bolt 28mm Spacer M10 x 75mm Bolt Metal Butterfly Bushing 1/2" Nylon Locknut M10 Small Washer...
... M8 x 58mm Bolt Weight Tube M10 x 58mm Carriage Bolt M6 Washer Plastic Butterfly Bushing Butterfly Cap Double "U"-bracket Pulley Plate Carriage Stop Bushing Square Bushing Rack Joint Plate "V"-pulley Pulley Cable Trap 17mm Spacer M10 x 75mm Carriage Bolt 28mm Spacer M10 x 75mm Bolt Metal Butterfly Bushing 1/2" Nylon Locknut M10 Small Washer...