Owner Manual
Page 3
...power source when not in use wire, rope, string, etc. • Use specified trimmer spool. Safety precautions must be diagnosed and repaired by the manufacturer. Make sure spool is marked with motor stopped. • Store the unit so the line limiter blade (on ...properly installed and all times. Store unit unplugged. • Do not hang unit so that are securely fastened. • Use only WEED EATER replacement parts and accessories as metal fences or pipes. • Ground Fault Circuit Interrupter (GFCI) protection should a means of children. Receptacles...
...power source when not in use wire, rope, string, etc. • Use specified trimmer spool. Safety precautions must be diagnosed and repaired by the manufacturer. Make sure spool is marked with motor stopped. • Store the unit so the line limiter blade (on ...properly installed and all times. Store unit unplugged. • Do not hang unit so that are securely fastened. • Use only WEED EATER replacement parts and accessories as metal fences or pipes. • Ground Fault Circuit Interrupter (GFCI) protection should a means of children. Receptacles...
Owner Manual
Page 6
.... 6 Without bending over the trimmer head. SELECT AN EXTENSION CORD Extension Cord Gauge Chart Length of cutting line is fed out, remove the spool cap and click spool counterclockwise until the line reaches the line limiter. Cord Retainer Extension Cord CORRECT OPERATING POSITION ADJUSTING TRIMMER HEIGHT The height of the cutting line...
.... 6 Without bending over the trimmer head. SELECT AN EXTENSION CORD Extension Cord Gauge Chart Length of cutting line is fed out, remove the spool cap and click spool counterclockwise until the line reaches the line limiter. Cord Retainer Extension Cord CORRECT OPERATING POSITION ADJUSTING TRIMMER HEIGHT The height of the cutting line...
Owner Manual
Page 8
... made periodically to 5 inches (7 -- 12 cm) unwound. AFTER EACH USE INSPECT AND CLEAN UNIT AND DECALS • After each use of spool Eyelet 11. Spool Cap Cap release latch 8. Notches Hub Eyelet 4. Use of damaged or worn parts. • Trigger Switch -- Cut out area of unit if...line about 1/2 inch (1 cm) into the notch, leaving 3 to properly maintain your unit. Replace with a pre--wound spool or cut out area of 0.065″ (1.65 mm) diameter WEED EATER brand line. Make sure motor stops. • Debris Shield -- Pull cap away from the warranty, the operator must ...
... made periodically to 5 inches (7 -- 12 cm) unwound. AFTER EACH USE INSPECT AND CLEAN UNIT AND DECALS • After each use of spool Eyelet 11. Spool Cap Cap release latch 8. Notches Hub Eyelet 4. Use of damaged or worn parts. • Trigger Switch -- Cut out area of unit if...line about 1/2 inch (1 cm) into the notch, leaving 3 to properly maintain your unit. Replace with a pre--wound spool or cut out area of 0.065″ (1.65 mm) diameter WEED EATER brand line. Make sure motor stops. • Debris Shield -- Pull cap away from the warranty, the operator must ...
Owner Manual
Page 9
...Line improperly routed in a high, dry place out of the reach of children. Use only 0.065 inch (1.65 mm) dia. Line welds onto spool. Replace spool. Crowding line against material being cut. 2. Line size incorrect. 1. Use only 0.065 inch (1.65 mm) dia. CAUSE 1. Debris stopping head.... into head. 1. Not enough line outside of head. 5. Rewind line tightly and evenly. 3. line. 4. Remove spool cap and pull 4 inches (10 cm) of line out of head. 5. Incorrect spool. 3. Line is being crowded against material being cut . 1. Line improperly routed in use . • Stop the...
...Line improperly routed in a high, dry place out of the reach of children. Use only 0.065 inch (1.65 mm) dia. Line welds onto spool. Replace spool. Crowding line against material being cut. 2. Line size incorrect. 1. Use only 0.065 inch (1.65 mm) dia. CAUSE 1. Debris stopping head.... into head. 1. Not enough line outside of head. 5. Rewind line tightly and evenly. 3. line. 4. Remove spool cap and pull 4 inches (10 cm) of line out of head. 5. Incorrect spool. 3. Line is being crowded against material being cut . 1. Line improperly routed in use . • Stop the...
Parts List
Page 1
Description Not Shown 115254226 Manual = New Part Number For This IPL = Refer to design changes. MODEL WE EL-15TNE Page: 1 2 43 1 WARNING All repairs, adjustments and maintenance not described in the Operator's Manual must be performed by Qualified Service Personnel... 7. 574495401 8. 574492201 Description Bolt Carriage, M6 X 1 Assist Handle Knob Clamp Edge Guide Spool with 0.065" Trimmer line Shield Assembly Spool Cap Ref. Parts List No. 966048001 Date 02/26/10 NEW WEED EATER R PARTS LIST NOTE : Illustration may differ from actual model due to the Service Reference Indicated...
Description Not Shown 115254226 Manual = New Part Number For This IPL = Refer to design changes. MODEL WE EL-15TNE Page: 1 2 43 1 WARNING All repairs, adjustments and maintenance not described in the Operator's Manual must be performed by Qualified Service Personnel... 7. 574495401 8. 574492201 Description Bolt Carriage, M6 X 1 Assist Handle Knob Clamp Edge Guide Spool with 0.065" Trimmer line Shield Assembly Spool Cap Ref. Parts List No. 966048001 Date 02/26/10 NEW WEED EATER R PARTS LIST NOTE : Illustration may differ from actual model due to the Service Reference Indicated...