Weed Eater WE EL-11 Support Question
Weed Eater WE EL-11 Support Question
Find answers below for this question about Weed Eater WE EL-11.Need a Weed Eater WE EL-11 manual? We have 2 online manuals for this item!
Question posted by joannelondon1958 on June 12th, 2021
How Do You Replace The Spool On A Weed Eater Weel11
how to replace the spool line
Current Answers
Answer #1: Posted by freginold on June 12th, 2021 7:48 PM
freginold
Member since:
December 20th, 2011 Points: 23,253,995
Member since:
December 20th, 2011 Points: 23,253,995
Page 7 of the user manual has instructions for replacing the spool:
https://www.manualslib.com/manual/189162/Weed-Eater-115253326.html?page=7#manual
https://www.manualslib.com/manual/189162/Weed-Eater-115253326.html?page=7#manual
Related Weed Eater WE EL-11 Manual Pages
Owner Manual - Page 2
... polarized extension cord will increase the risk of electrical shock, do not use and replace if damaged. Inspect extension cord before using electric gar- Keep children, bystanders, and ...does not fit, obtain a correct polarized extension cord. S Avoid unintentional starting of rotating line. Make sure your finger on unit. Read and follow unit and manual warnings and ...
Owner Manual - Page 3
...065 inch (1.65 mm) diameter recommended trimmer line (see ATTACH THE EXTENSION CORD TO YOUR TRIMMER in place and securely fastened. S Use specified trimmer spool.
Do not expose cords to avoid overheating...intended to
this unit.
S Use only WEED EATER replacement parts and accessories as metal fences or pipes. Use only for changing trimmer line. Never carry the unit by the ...
Owner Manual - Page 4
... securely. Ensure locking sleeve assembly and alignment decals appear as shown.
erly installed. The line limiter blade (on a flat surface. 2. Ensure the cutting head remains free to ensure...
tube. ASSEMBLY
WARNING: If received assembled,
review all assembly steps to rotate and the line is not caught between the shield and the motor housing (See following illustration).
2.
DO...
Owner Manual - Page 5
...UNIT.
TRIMMER HEAD The TRIMMER HEAD holds cutting line and rotates during line replacement.
5
Release to operate the unit. TAP ... . Trimmer Line Tap Button
Line Limiter Blade
RECESSED PLUG The RECESSED PLUG is used to advance the cutting line during operation ... various controls and adjustments. LINE LIMITER BLADE The LINE LIMITER BLADE cuts the cutting line to help hold and guide...
Owner Manual - Page 6
... the proper length. Trimming
Extension Cord CORRECT OPERATING POSITION
3 in places conventional lawn mowers cannot reach.
tion. ADVANCING THE CUTTING LINE Advance line by tapping bottom of cutting head lightly on your unit. A metal line limiter blade attached to the ground. Avoid pressing the head into eyes and face and cause blindness or other...
Owner Manual - Page 7
...spool into the notch, leaving 3 to side.
Discontinue use of heavier lines could overload and damage unit. Insert one end of the line about 1/2 inch (1 cm) into place.
11...065″ (1.65 mm) diameter WEED EATER brand line. Ensure switch functions
properly by firmly pulling on the spool.
7. SERVICE AND ADJUSTMENTS
REPLACING THE LINE 1. Push the line into the hub until it from ...
Owner Manual - Page 8
... in . (1.65 mm) dia. TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before performing
all guards in place.
Line improperly wound into head.
1. Check line routing. 2. Replace spool. 1. Replace spool. 3. Position unit so that require unit to do the cutting.
2. TROUBLE
Trimmer head stops under a load or does not turn when switch...
Owner Manual - Page 9
... predelivery set--up or normal adjustments explained in complete condition, prepaid, with reasonable use of accessories and/or attachments not specifically recommended by WEED EATER for repair or replacement at any time without notice or obligation to any unanswered questions concerning this warranty does not cover parts that term as defined in the...
Parts List - Page 1
...
Date 02/24/10
NEW
WEED EATER R PARTS LIST
NOTE : Illustration may differ from actual model due to the Service Reference Indicated for more information.(Located at the END of the IPL) Part No.
1. 574473001 2. 574473101
3. 574473201 4. 574471501 5. 952701663
Description
Assit Handle Knob Bolt Carriage, M6 X 1 Shield Assembly Spool with 0.065" Trimmer line
Ref.
Similar Questions
How Long Should The Replacement Fillament Line Be To Be Rewinded? 10, 25, ?
(Posted by javiervalenciano 8 years ago)
Where Can I Find A Replacement Cutting Guard For The We El11?
(Posted by Anonymous-154000 8 years ago)
Weed Eater Part Quest
Hi, Can anyone tell me the exact dimensions of the screw that anchors the Cutting Guard of the Weed...
Hi, Can anyone tell me the exact dimensions of the screw that anchors the Cutting Guard of the Weed...
(Posted by KarlB17 10 years ago)
