Operation Manual
Page 2
... is idling. Always keep all warnings and safety instructions. All U.S. Attention is hot. OR 1-800-668-1238 in CANADA DANGER: Failure to the head, hands and feet. • Clear the area of such materials. • Always stop the unit immediately. • Use only 0.095 inch,...shield must follow the safety precautions to the idle position. The safety warnings do so can result in a stable position while starting . Replace parts that meet ANSI Z87.-1989 standards and are cracked, chipped, or damaged in property damage or personal injury to yourself or to obey...
... is idling. Always keep all warnings and safety instructions. All U.S. Attention is hot. OR 1-800-668-1238 in CANADA DANGER: Failure to the head, hands and feet. • Clear the area of such materials. • Always stop the unit immediately. • Use only 0.095 inch,...shield must follow the safety precautions to the idle position. The safety warnings do so can result in a stable position while starting . Replace parts that meet ANSI Z87.-1989 standards and are cracked, chipped, or damaged in property damage or personal injury to yourself or to obey...
Operation Manual
Page 8
... these required maintenance procedures at a time. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by letting it pop off Inner or a slight wiggle of the cap may have spilled. Arrow Cutting Head Knob Fig. 16 1. Start the unit and bump the...handling the unit. Fig. 20 5. Never operate the unit with the cutting head shield hanging off the outer spool (Fig. 20). Check the level, See Checking the Oil Level. If the level is in the crankcase. Replace the oil fill plug. 7. Disconnect the spark plug wire to get a ...
... these required maintenance procedures at a time. NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by letting it pop off Inner or a slight wiggle of the cap may have spilled. Arrow Cutting Head Knob Fig. 16 1. Start the unit and bump the...handling the unit. Fig. 20 5. Never operate the unit with the cutting head shield hanging off the outer spool (Fig. 20). Check the level, See Checking the Oil Level. If the level is in the crankcase. Replace the oil fill plug. 7. Disconnect the spark plug wire to get a ...
Operation Manual
Page 9
.... 29). 8. Grasp the plug wire firmly and pull the cap from around the spark plug. Clean dirt from the cylinder head by turning a 5/8 in detergent and water. Replace cracked, fouled or dirty spark plug. Install a correctly-gapped spark plug in . (0.127 mm) feeler gauge. socket clockwise ...for both the intake and exhaust valves. Use a standard automotive .005 in the cylinder head. The feeler gauge should be performed inside, in . (.076 - 0.152 mm). Turn the adjusting nut using a new gasket. See Replacing the Spark Plug. 11. Fig. 32 Rocker Arm Cover Spark Plug Hole Fig. ...
.... 29). 8. Grasp the plug wire firmly and pull the cap from around the spark plug. Clean dirt from the cylinder head by turning a 5/8 in detergent and water. Replace cracked, fouled or dirty spark plug. Install a correctly-gapped spark plug in . (0.127 mm) feeler gauge. socket clockwise ...for both the intake and exhaust valves. Use a standard automotive .005 in the cylinder head. The feeler gauge should be performed inside, in . (.076 - 0.152 mm). Turn the adjusting nut using a new gasket. See Replacing the Spark Plug. 11. Fig. 32 Rocker Arm Cover Spark Plug Hole Fig. ...
Operation Manual
Page 10
... container. You may reach an open flame or spark. • Allow the engine to cool before storing. • Lock up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Line twisted when refilled Not enough line is above 90˚ F Move the ...Crankcase Oil Capacity 3.04 oz (90 ml) Fuel Unleaded Fuel Tank Capacity 14 oz (414 ml) Approximate Weight (without notice. 10 Repair or replace damaged parts and tighten loose screws, nuts or bolts. Then move the choke lever to cool. Allow the engine to Position 3. SPECIFICATIONS* Engine Type...
... container. You may reach an open flame or spark. • Allow the engine to cool before storing. • Lock up Replace the inner reel Cutting head dirty Clean inner reel and outer spool Line welded Line twisted when refilled Not enough line is above 90˚ F Move the ...Crankcase Oil Capacity 3.04 oz (90 ml) Fuel Unleaded Fuel Tank Capacity 14 oz (414 ml) Approximate Weight (without notice. 10 Repair or replace damaged parts and tighten loose screws, nuts or bolts. Then move the choke lever to cool. Allow the engine to Position 3. SPECIFICATIONS* Engine Type...