Troy-Bilt TB525 Support Question
Troy-Bilt TB525 Support Question
Find answers below for this question about Troy-Bilt TB525.Need a Troy-Bilt TB525 manual? We have 2 online manuals for this item!
Question posted by troopfranco on August 16th, 2013
Replace The Spool Assembly
i need to replace the spool assembly
Current Answers
Related Troy-Bilt TB525 Manual Pages
Operation Manual - Page 1
...'s Manual
Electric Start Capable 4-Cycle Gas Trimmer
TB525 EC
TABLE OF CONTENTS Service Information 1 Rules for Safe Operation 2 Know Your Unit 4 Assembly Instructions 4 Oil and Fuel Information 5 Starting and...performed by an authorized and approved service dealer. When servicing, use only identical replacement parts. For service, please call the Customer Support Department at 1-800-828-...
Operation Manual - Page 2
... precautions to reduce the risk of California to the idle position. Replace parts that it requires replacement, ask your state or local authorities for regulations pertaining to possible dangers...unit immediately. • Use only 0.095 inch, 2.41 mm diameter original equipment manufacturer replacement line. WARNING: Failure to obey a safety warning can result in order to the head,...
Operation Manual - Page 3
...manual describes safety and international symbols and pictographs that fuel containing greater
than the speed needed .
• UNLEADED FUEL Always use them to another.
• If you... complete safety, assembly, operating, maintenance, and repair information. If you strike or become lodged between the cutting attachment and shield.
• To reduce fire hazard, replace a faulty muffler...
Operation Manual - Page 4
...; 3/8" Socket
Spark Plug Choke Lever
Muffler
Starter Rope Grip
Shaft Grip On/Off Stop Control
D-Handle
Throttle Control
Fuel Cap
Primer Bulb
Air Filter Cover
ASSEMBLY INSTRUCTIONS
INSTALL CUTTING ATTACHMENT SHIELD
WARNING: To prevent serious personal injury, never operate
the trimmer without the cutting attachment shield in the guard mounting bracket...
Operation Manual - Page 5
... in the carburetor for up to use and change it as ethanol, methanol or MTBE (ether). Replace the top. NOTE: Never add oil to the unit's gas tank.
5
RECOMMENDED FUEL TYPE
FUELING...position. Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates such as needed . Use fresh fuel (less than 10% ethanol will inhibit corrosion and minimize the formation of ...
Operation Manual - Page 6
... On/Off Stop Control switch in the bulb, press and release the bulb until fuel is no need to Fueling the Unit. Release your hand from the unit.
10. Make sure you are in ...Position
7. Continue to warm up when the engine accelerates without hesitation.
The On/Off Stop Control is no need to a complete stop (Fig. 7).
6 Press and hold the On/Off Stop Control switch in the ...
Operation Manual - Page 7
...soil.
ADJUSTING TRIMMING LINE LENGTH
WARNING: Do not remove or alter the line cutting blade
assembly. Upper Shaft Housing
Lower Shaft Housing
Fig. 11
NOTE: Place the unit on the...INSTRUCTIONS
OPERATING THE EZ-LINK™ SYSTEM
WARNING: Before you to release trimming line without the need to bend over 8 inches (200 mm) by removing all safety information contained within.
Always keep...
Operation Manual - Page 8
NOTE: Maintenance, replacement, or repair of the emission control devices and system may be performed by letting it pop off Inner or a slight wiggle of the cap may be a need to remove the bump cap if the old line gets jammed or an obstruction preventing the new line from the outer spool. (Fig. 21...
Operation Manual - Page 9
... is operated without binding (Fig. 34 and 35).
8. Measure both clearances, and adjust as needed ) until the engine idles smoothly. The feeler gauge should slide between the rocker arm and valve...engine and allow it to dry.
4. Remove the spark plug from around the rocker arm cover. Replace cracked, fouled or dirty spark plug. If using a feeler gauge (Fig. 36).
5.
WARNING:...
Operation Manual - Page 10
... fumes may reach an open
flame or spark. • Allow the engine to cool before storing. • Lock up
Replace the inner reel
Cutting head dirty
Clean inner reel and outer spool
Line welded Line twisted when refilled Not enough line is exposed
Disassemble, remove the welded section and rewind
Disassemble and...
Parts Diagram - Page 2
REPLACEMENT PARTS - MODEL TB525EC
4-CYCLE GAS TRIMMER
PPN 41EDT52C966
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ...-181025 753-05297 753-06317
Description O-Ring Air Cleaner Cover Assembly (includes 26) Air Filter Screw Fuel Tank Assembly w/Fuel Lines (includes 29) Fuel Cap Fuel Tank Pads Starter Housing Assembly (includes 3) Clutch Assembly Clutch Cover (includes 2) Anti-Rotation Screw Clamp Screw Nut...
Parts Diagram - Page 3
... Knob (includes 13) Knob Retaining Nut Lower Drive Shaft Housing Assembly (includes 16) Lower Clamp Assembly (includes 19) Lower Flexible Drive Shaft Shield Mounting Screw Bushing Housing Assembly Anti-Rotation Screw Shield Assembly (includes 21) Blade Assembly Adapter Spool Assembly
7
10 11
12
9 13
14
16 15
20
17
21
19
18
22 23
Issued 2/10 REPLACEMENT PARTS -
Similar Questions
Proline Frt Tiller Return Spring Assembly
I have replaced the drive belts on my tiller..........I can't figure out where the return spring on ...
I have replaced the drive belts on my tiller..........I can't figure out where the return spring on ...
(Posted by melnichukjohn 2 years ago)
What Needs To Be Replaced
I love my machine..but right now it doesn't throw snow very well at all (it used to). Do I need to r...
I love my machine..but right now it doesn't throw snow very well at all (it used to). Do I need to r...
(Posted by mfitz7834 2 years ago)
How To Remove Cutting Head
How To Remove Cutting Head From Tb525 Ec Trimmer
How To Remove Cutting Head From Tb525 Ec Trimmer
(Posted by godez 10 years ago)