Operation Manual
Page 1
...on a level surface, remove the oil plug from the carton. 2 Insert the upper blower tube into the blower outlet and turn it clockwise until it locks into place. 3 Install the lower blower tube onto the upper blower tube and turn it clockwise until it locks into the fill hole. PAGE 6 ESPA... engine starts IF unit still fails to warm up . Call 1-800-828-5500 in Canada 769-06521 P00 03/11 PAGE 1 TB4HB EC 4-Cycle Electric Start Capable Handheld Blower Operator's Manual Removing Unit From Carton Assemble The Unit Tools Required: • Flathead Screwdriver On/Off Switch...
...on a level surface, remove the oil plug from the carton. 2 Insert the upper blower tube into the blower outlet and turn it clockwise until it locks into place. 3 Install the lower blower tube onto the upper blower tube and turn it clockwise until it locks into the fill hole. PAGE 6 ESPA... engine starts IF unit still fails to warm up . Call 1-800-828-5500 in Canada 769-06521 P00 03/11 PAGE 1 TB4HB EC 4-Cycle Electric Start Capable Handheld Blower Operator's Manual Removing Unit From Carton Assemble The Unit Tools Required: • Flathead Screwdriver On/Off Switch...
Operation Manual
Page 2
...from all fasteners are in this manual are based on this unit. Use of information or instructions vital to install or remove the blower tubes. Do not operate before filling the tank. SAFETY WARNINGS FOR GAS UNITS WARNING: Gasoline is factory equipped with your...identical replacement parts. Always follow the safety precautions to these instructions for the prevention of the operator and any maintenance or servicing. • BLOWERS - CAUTION: Failure to ensure the safety of fire. Replace parts that are no longer turning to avoid contact with the rotating ...
...from all fasteners are in this manual are based on this unit. Use of information or instructions vital to install or remove the blower tubes. Do not operate before filling the tank. SAFETY WARNINGS FOR GAS UNITS WARNING: Gasoline is factory equipped with your...identical replacement parts. Always follow the safety precautions to these instructions for the prevention of the operator and any maintenance or servicing. • BLOWERS - CAUTION: Failure to ensure the safety of fire. Replace parts that are no longer turning to avoid contact with the rotating ...
Operation Manual
Page 3
... fuel cannot be started in a controlled motion. Move the choke lever to Fueling the Unit. Squeeze and hold (Fig. 3). 3. Twist the lower blower tube clockwise until fuel vapors dissipate. 1. Insert a flathead screwdriver into the oil fill hole (Fig. 6). Unscrew the top of the... on the top end of this time. 3 Remove the electric starter or drill from forming harmful deposits in the starting . Insert the upper blower tube into place (Fig. 1). Fig. 3 OIL AND FUEL INFORMATION RECOMMENDED OIL TYPE WARNING: OVERFILLING OIL CRANKCASE MAY CAUSE SERIOUS PERSONAL INJURY....
... fuel cannot be started in a controlled motion. Move the choke lever to Fueling the Unit. Squeeze and hold (Fig. 3). 3. Twist the lower blower tube clockwise until fuel vapors dissipate. 1. Insert a flathead screwdriver into the oil fill hole (Fig. 6). Unscrew the top of the... on the top end of this time. 3 Remove the electric starter or drill from forming harmful deposits in the starting . Insert the upper blower tube into place (Fig. 1). Fig. 3 OIL AND FUEL INFORMATION RECOMMENDED OIL TYPE WARNING: OVERFILLING OIL CRANKCASE MAY CAUSE SERIOUS PERSONAL INJURY....
Operation Manual
Page 4
... cracked, fouled or dirty spark plug. Turn the 5/8 in . (0.127 mm) feeler gauge. STOPPING INSTRUCTIONS 1. OPERATING INSTRUCTIONS HOLDING THE BLOWER Before operating the unit, stand in good working condition • The tubes are not true, repeat this procedure until the oil level reaches...California/EPA statement that : • The piston is in the operating position and check for 2-second intervals until the unit comes to a Troy-Bilt or other equipment. The oil should also be just touching the innermost thread (Fig. 13). 6. See Checking the Oil Level. 6. ...
... cracked, fouled or dirty spark plug. Turn the 5/8 in . (0.127 mm) feeler gauge. STOPPING INSTRUCTIONS 1. OPERATING INSTRUCTIONS HOLDING THE BLOWER Before operating the unit, stand in good working condition • The tubes are not true, repeat this procedure until the oil level reaches...California/EPA statement that : • The piston is in the operating position and check for 2-second intervals until the unit comes to a Troy-Bilt or other equipment. The oil should also be just touching the innermost thread (Fig. 13). 6. See Checking the Oil Level. 6. ...
Operation Manual
Page 5
...loose screws, nuts or bolts. You may reach an open flame or spark. • Allow the engine to cool before attempting to start the blower after storage. 4. Do not use or damage. • Store the unit in accordance with fuel in the tank where fumes may also go to 450... plug SPECIFICATIONS* Engine Type...Air-Cooled, 4-Cycle Displacement ...25 cc Operating RPM ...7,000 rpm Idle Speed RPM ...3,600 - 4,600 rpm Blower Velocity up to 150 mph (240 kmh) Blower Air Output up the unit to distribute the oil. NOTE: Remove the spark plug and drain all gasoline from the cylinder before...
...loose screws, nuts or bolts. You may reach an open flame or spark. • Allow the engine to cool before attempting to start the blower after storage. 4. Do not use or damage. • Store the unit in accordance with fuel in the tank where fumes may also go to 450... plug SPECIFICATIONS* Engine Type...Air-Cooled, 4-Cycle Displacement ...25 cc Operating RPM ...7,000 rpm Idle Speed RPM ...3,600 - 4,600 rpm Blower Velocity up to 150 mph (240 kmh) Blower Air Output up the unit to distribute the oil. NOTE: Remove the spark plug and drain all gasoline from the cylinder before...