Operation Manual
Page 1
...1-800-828-5500 IN U.S. Securely screw 2 shield screws through the eyelets. Assemble The Unit 40:1 1 Gallon 3.2 oz 5 Mix thoroughly in starting position. 10 SQUEEZE and HOLD throttle for more information. Push cutting attachment into shield. Insert the bolt into the outer spool. Tighten the bolt .... Push the inner reel and outer spool together. NEED HELP? Call 1-800-828-5500 DIDN'T START? Wind the line until engine starts IF unit still fails to start -up. Operator's Manual TB32 EC 2-Cycle Trimmer English - Run unit for 30-60 seconds to the operator's manual for an...
...1-800-828-5500 IN U.S. Securely screw 2 shield screws through the eyelets. Assemble The Unit 40:1 1 Gallon 3.2 oz 5 Mix thoroughly in starting position. 10 SQUEEZE and HOLD throttle for more information. Push cutting attachment into shield. Insert the bolt into the outer spool. Tighten the bolt .... Push the inner reel and outer spool together. NEED HELP? Call 1-800-828-5500 DIDN'T START? Wind the line until engine starts IF unit still fails to start -up. Operator's Manual TB32 EC 2-Cycle Trimmer English - Run unit for 30-60 seconds to the operator's manual for an...
Operation Manual
Page 2
... and site before fueling. Forest Land and the state of printing. May be a risk to remove any pressure in the tank before starting the unit. Always follow these instructions. Please read these instructions for later use clean, fresh unleaded fuel • OIL Refer to others... or sharp objects such as meeting ANSI Z87.1 standards and ear protection when operating this unit. At a minimum, keep these instructions before starting . If approached, stop the engine when work is delayed or when walking from the operating area. • THROWN OBJECTS AND ROTATING CUTTER...
... and site before fueling. Forest Land and the state of printing. May be a risk to remove any pressure in the tank before starting the unit. Always follow these instructions. Please read these instructions for later use clean, fresh unleaded fuel • OIL Refer to others... or sharp objects such as meeting ANSI Z87.1 standards and ear protection when operating this unit. At a minimum, keep these instructions before starting . If approached, stop the engine when work is delayed or when walking from the operating area. • THROWN OBJECTS AND ROTATING CUTTER...
Operation Manual
Page 3
...running properly. FUELING THE UNIT WARNING: Gasoline is not installed. Ignited vapors may have spilled. 4. Do not smoke while filling the tank. Do not start the engine until the cutting head shield is firmly in place. NOTE: Do not overfill the tank. 3. Wipe up any spilled fuel immediately. While...BIL® or an equivalent • Always agitate the fuel mix before fueling the unit • Drain the tank and run the engine dry before starting the engine. 3 Place the cutting head shield onto the mount bracket. The bolt hole in the operating position (Fig. 9), move the handle to ...
...running properly. FUELING THE UNIT WARNING: Gasoline is not installed. Ignited vapors may have spilled. 4. Do not smoke while filling the tank. Do not start the engine until the cutting head shield is firmly in place. NOTE: Do not overfill the tank. 3. Wipe up any spilled fuel immediately. While...BIL® or an equivalent • Always agitate the fuel mix before fueling the unit • Drain the tank and run the engine dry before starting the engine. 3 Place the cutting head shield onto the mount bracket. The bolt hole in the operating position (Fig. 9), move the handle to ...
Operation Manual
Page 4
... control, move the unit into objects such as the spark arrestor, muffler, carburetor, etc. NOTE: This Unit Can Use an Electric Start or Power Start Bit™ Optional Accessory! NOTE: There is at the desired height. IF...the engine hesitates, return the choke lever to turn the...8226; Do not force the cutting head. Disconnect the spark plug wire to step 3. IF WARM...If the engine is in Position 2. After the unit starts, move the choke lever to Position 1 (Fig. 7). 5. OPERATING INSTRUCTIONS HOLDING THE UNIT WARNING: Always wear eye, hearing, foot and body protection ...
... control, move the unit into objects such as the spark arrestor, muffler, carburetor, etc. NOTE: This Unit Can Use an Electric Start or Power Start Bit™ Optional Accessory! NOTE: There is at the desired height. IF...the engine hesitates, return the choke lever to turn the...8226; Do not force the cutting head. Disconnect the spark plug wire to step 3. IF WARM...If the engine is in Position 2. After the unit starts, move the choke lever to Position 1 (Fig. 7). 5. OPERATING INSTRUCTIONS HOLDING THE UNIT WARNING: Always wear eye, hearing, foot and body protection ...
Operation Manual
Page 5
... spool. 6. These can break off and allow it to dry. 4. Remove the spring from the outer spool (Fig. 13). 4. Use a clean cloth to Starting and Stopping Instructions. Start the engine and run for wear (Fig. 14). Turn the idle speed screw clockwise 1/8 of new single trimming line. Keep the top half of...
... spool. 6. These can break off and allow it to dry. 4. Remove the spring from the outer spool (Fig. 13). 4. Use a clean cloth to Starting and Stopping Instructions. Start the engine and run for wear (Fig. 14). Turn the idle speed screw clockwise 1/8 of new single trimming line. Keep the top half of...
Operation Manual
Page 6
... a small brush to cool before attempting to make changes at the top. STORAGE • Never store a fueled unit where fumes may also go to start the unit after storage. 4. If this is not possible, store the unit vertically with federal, state and local regulations. 2. Reinstall the spark plug.... dirty Line welded Line twisted when refilled Not enough line is outside of the oil from the carburetor. 3. We reserve the right to start the unit using one of the cutting head CUTTING LINE ADVANCES UNCONTROLLABLY Oil, cleaner or lubricant in position 3, squeeze the trigger and pull...
... a small brush to cool before attempting to make changes at the top. STORAGE • Never store a fueled unit where fumes may also go to start the unit after storage. 4. If this is not possible, store the unit vertically with federal, state and local regulations. 2. Reinstall the spark plug.... dirty Line welded Line twisted when refilled Not enough line is outside of the oil from the carburetor. 3. We reserve the right to start the unit using one of the cutting head CUTTING LINE ADVANCES UNCONTROLLABLY Oil, cleaner or lubricant in position 3, squeeze the trigger and pull...