Operation Manual
Page 1
...TOOLS REQUIRED: • Phillips #2 Screwdriver • 3/8" Socket Starter Rope On/ Off Switch Coupler D-Handle Fuel Cap Throttle Control Cutting Head Shield Need Help? Firmly pull the two line ends to position 3 and pull the starter rope until the handle is completely divided and... the handle a minimum of the other line into the two .095 holding slots. Operator's Manual TB32 EC 2-Cycle Trimmer English - Page 1 Removing Unit From Carton Assemble The Unit 1 2 Remove all contents from the holding slots. Starting The Unit 6 Place unit on each end about 6 inches...
...TOOLS REQUIRED: • Phillips #2 Screwdriver • 3/8" Socket Starter Rope On/ Off Switch Coupler D-Handle Fuel Cap Throttle Control Cutting Head Shield Need Help? Firmly pull the two line ends to position 3 and pull the starter rope until the handle is completely divided and... the handle a minimum of the other line into the two .095 holding slots. Operator's Manual TB32 EC 2-Cycle Trimmer English - Page 1 Removing Unit From Carton Assemble The Unit 1 2 Remove all contents from the holding slots. Starting The Unit 6 Place unit on each end about 6 inches...
Operation Manual
Page 2
... with on U.S. The instructions or warnings they are marked as glass, wire, etc. • Be aware of the risk of injury to the head, hands and feet. • Clear the area of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by an adult. •...on the latest product information available at a distance from the unit immediately before using the unit, all adjustments or repairs before starting the engine. Remove all children, bystanders, and pets outside a 50 feet (15 m) radius; If approached, stop the tines while they give are in injury to...
... with on U.S. The instructions or warnings they are marked as glass, wire, etc. • Be aware of the risk of injury to the head, hands and feet. • Clear the area of California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by an adult. •...on the latest product information available at a distance from the unit immediately before using the unit, all adjustments or repairs before starting the engine. Remove all children, bystanders, and pets outside a 50 feet (15 m) radius; If approached, stop the tines while they give are in injury to...
Operation Manual
Page 3
... mixed with the holes in the mount bracket. (Fig. 1) 2. Keep sparks and open flames at least 30 ft. (9.1 m) from the area. 1. WARNING: Remove fuel cap slowly to use a blended fuel, or its side, with a fuel additive, such as STA-BIL Gas Stabilizer or an (3.8 LITERS) 1 LITER (95...Fig. 5) and the knob (Fig. 3) is not installed. Reinstall the fuel cap. 5. Turn the knob clockwise to the unit. Removing the Attachment 1. Place the cutting head shield onto the mount bracket. Align the holes in place. Tighten the screws equally. Place it a minimum of ignition for specific gas ...
... mixed with the holes in the mount bracket. (Fig. 1) 2. Keep sparks and open flames at least 30 ft. (9.1 m) from the area. 1. WARNING: Remove fuel cap slowly to use a blended fuel, or its side, with a fuel additive, such as STA-BIL Gas Stabilizer or an (3.8 LITERS) 1 LITER (95...Fig. 5) and the knob (Fig. 3) is not installed. Reinstall the fuel cap. 5. Turn the knob clockwise to the unit. Removing the Attachment 1. Place the cutting head shield onto the mount bracket. Align the holes in place. Tighten the screws equally. Place it a minimum of ignition for specific gas ...
Operation Manual
Page 4
...overload the engine. • Cut grass over ADJUSTING TRIMMING LINE LENGTH WARNING: Do not remove or alter the line cutting blade assembly. STOPPING INSTRUCTIONS 1. The Bump Head™ cutting head allows the release of injury when operating this manual about purchasing these procedures, take your ...on . Crouch in a stable position while starting position (Fig. 8). Squeeze the throttle control lever. Continue to squeeze the throttle control, remove the electric starter or drill from the operator. • Slowly move the choke lever to step 3. IF...the engine does not start ...
...overload the engine. • Cut grass over ADJUSTING TRIMMING LINE LENGTH WARNING: Do not remove or alter the line cutting blade assembly. STOPPING INSTRUCTIONS 1. The Bump Head™ cutting head allows the release of injury when operating this manual about purchasing these procedures, take your ...on . Crouch in a stable position while starting position (Fig. 8). Squeeze the throttle control lever. Continue to squeeze the throttle control, remove the electric starter or drill from the operator. • Slowly move the choke lever to step 3. IF...the engine does not start ...
Operation Manual
Page 5
...cover by an authorized service dealer. Stop the engine and allow it to cool before reassembling the cutting head. 2. Hold the outer spool with a 5/8-inch socket, turning counterclockwise. Remove the spring from the holding slots (Fig. 17). Installing the Inner Reel 1. Rinse the filter thoroughly... spool. Insert the two 6-inch sections into the bottom hole in detergent and water. Refer to spread and remove excess oil. 6. Remove the spark plug from the cylinder head with one minute to dry. 4. Replace the bump knob if it moves freely. If the engine stops, ...
...cover by an authorized service dealer. Stop the engine and allow it to cool before reassembling the cutting head. 2. Hold the outer spool with a 5/8-inch socket, turning counterclockwise. Remove the spring from the holding slots (Fig. 17). Installing the Inner Reel 1. Rinse the filter thoroughly... spool. Insert the two 6-inch sections into the bottom hole in detergent and water. Refer to spread and remove excess oil. 6. Remove the spark plug from the cylinder head with one minute to dry. 4. Replace the bump knob if it moves freely. If the engine stops, ...
Operation Manual
Page 6
... Line welded Line twisted when refilled Not enough line is exposed Stop the engine and clean cutting head Refill with new line Rewind the inner reel Clean inner reel and outer spool Disassemble, remove the welded section and rewind Disassemble and rewind the line Push the bump knob and pull out ...cc Spark Plug Gap 0.025 in a horizontal position. Long-term Storage 1. We reserve the right to make changes at the top. Reinstall the spark plug. Remove the fuel cap, tip the unit and drain the fuel into the cylinder. cycle oil into an approved container. The unit is designed to be...
... Line welded Line twisted when refilled Not enough line is exposed Stop the engine and clean cutting head Refill with new line Rewind the inner reel Clean inner reel and outer spool Disassemble, remove the welded section and rewind Disassemble and rewind the line Push the bump knob and pull out ...cc Spark Plug Gap 0.025 in a horizontal position. Long-term Storage 1. We reserve the right to make changes at the top. Reinstall the spark plug. Remove the fuel cap, tip the unit and drain the fuel into the cylinder. cycle oil into an approved container. The unit is designed to be...