TRENDnet TK-RP08 Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TK-RP08 manuals!
Problems with TRENDnet TK-RP08?
Ask a Question
Free TRENDnet TK-RP08 manuals!
Problems with TRENDnet TK-RP08?
Ask a Question
Popular TRENDnet TK-RP08 Manual Pages
User's Guide - Page 4
...-powered devices
▪ Unit management using a host PC connected via its specification. With our highly reliable and quality product, user can use extra adapter cords between ioPower and your usage, for 2 seconds to a host PC installed with multiple units into the CDROM drive of the Host PC, and then install the
1 Serial Power Control Unit
Introduction
The TK-RP08 provides 8 AC power...
User's Guide - Page 5
... control the power on TK-RP08 backpanel. for the EU Region
POWER Reset button
Power Input ( IEC 320 C14 ) 11-~240 Vac@60Hz
Daisy-chain port (RJ-45) - "One-touch" Power ON/OFF via the TK-RP08 Management Software Interface or set the timer to the following instructions. The front-panel buttons implement a time-delayed and action upon button release.
The installer...
User's Guide - Page 6
...However, to avoid accidental mistakes, TK-RP08 Management software will automatically detect COM port for 2 " .... Setting/Connect
When TK-RP08 is in the following picture, it means you have free choice to disable/enable the confirmation prompt according one -touch" power on the message Box. Power Management Software Interface
When running the TK-RP08 Management Software, you should see...
User's Guide - Page 7
...from host PC.
You can use the Windows HyperTerminal to perform firmware upgrade, please refer to the Firmware Upgrade Operation Guide that comes with your firmware upgrade file.
Setting/Configuration
Click Setting/Configuration to your TK-RP08 unit is restarted.
After you can either get it from your COM port setting as any of all available banks) to start ioPower Management...
User's Guide - Page 8
... (previous) timer settings once again. To set timer settings on /off . To clear all timer settings of these options for simultaneous power on/off all ports on a specific bank or on /off at preset time Every week ...to specify the bank/port and time/duration for selection:
After ... However, if the TK-RP08 Unit
has been powered down combo boxes...
User's Guide - Page 9
... TK-RP08 units. If you see a lit Alarm LED, you perform a firmware upgrade on TK-RP08, all sequent setting possibility on that the corresponding power output port is put out of function by pressing several times its power button on the front-panel of TK-RP08, to check the firmware version of any specific bank of your firmware is now suffering form a current overloads. Firmware Upgrade...
User's Guide - Page 10
... Guide. Step 4. Configure your current unit with an available RS-232 port (DB9) (2) the TKRP08 Unit to be sure to the Quick Installation section on your PC and a shortcut with a DB9-to
your local computer. The TK-RP08 allows its user to upgrade firmware contents whenever is described below. Please refer to have powered on both your HyperTerminal program menu.
Power Control...
User's Guide - Page 13
...
Select various Power Control features. Install the TK-RP08 as a Power Control Accessory for the TK-IP101 Switch
The TK-RP08 can be used in order to enable the remote power control function that the TK-IP101 and TK-RP08 are going to TK-IP101 User Guide, Section 4.11, KVM Server/Power Control -
Use the serial power control cable that supports a standard serial power control. TK-IP101...
User's Guide - Page 14
...Settings button. Usually, you have made all modifications, click Store Settings to a specific port.
Then you have to power on the Serial Power control device you used behind TK-IP101, sometimes you hit the Apply Settings... TK-IP101 allows only Super admin and admin the right to enter any script, since TK-RP08 does not need a login script to activate the remote power control support ...
User's Guide - Page 15
... - Important Note: To remotely power on/ off command remotely across internet by using any other IP KVM switch that has been installed with an TK-RP08.
By default this delay is processed only if you hit Apply Settings/Restart Servers! (Also refer to perform power on bank 1.
Access the Viewer Quick Menu by clicking its manual instructions.
The command specified...
User's Guide - Page 16
...Power on status bar at the bottom of bank number or port number (such as ON 1 3). 2. However, if you can accept their singledigit entries (such as ON 1 3), and also allow multiple blank spaces in between TK-RP08... but can use the serial commands for TK-RP08 control, you have to the following parameters for ...
Command usage notes:
1. Serial Command Set
Before you use the serial command ......
User's Guide - Page 17
...(s) immediately [Usage] ON [bank_number] [port_number] [Examples] ON 1 4 -
Timer Activate at specific time point [Description]Set the timer to power off a specific port at 00:10:00 TA 0 0 OF 01:00:00 - Power on all cascaded banks immediately Notes: 1. A port number of 0 represents all ports;
Set timer to power on port 4 on all ports on bank 1 exactly
at...
User's Guide - Page 18
... turn on port 4 of 0 represents all cascaded banks. 2.
Timer Activate everyday at a specific time point [Description]Set the timer to power off a specific port every day at 00:10:00. ED 1 0 ON 00:10:00 - Set timer to power on all ports; Set timer to power on port 4 on /off all ports on all cascaded
banks every day...
User's Guide - Page 19
... the firmware version of all bank
16 Show the system status of bank 1 VER 16 - Upgrade Firmware [Description]Upgrade the system firmware [Usage] UPGRADE [Example] UPGRADE Note: Please also refer to be 2004/09/27 18:10:00
GETTIME - SETTIME - Set Up System Date and Time [Description]Set up the system Date and time to ioPower Flash Operation Guide for...
Quick Installation Guide - Page 9
... releasing. Third, make sure to press the power button for the power outlet on the TK-RP08. A2: First, make sure the AC powered device is properly plugged into the power outlet.
has been exceeded.
A5: Yes you still encounter problems or have any questions regarding the TK-RP08, please contact Trendnet's Technical Support Department.
7 Second, make sure the computer is...
TRENDnet TK-RP08 Reviews
We have not received any reviews for TRENDnet yet.