TRENDnet TEG-S4000i Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TEG-S4000i manuals!
Problems with TRENDnet TEG-S4000i?
Ask a Question
Free TRENDnet TEG-S4000i manuals!
Problems with TRENDnet TEG-S4000i?
Ask a Question
Popular TRENDnet TEG-S4000i Manual Pages
Data Sheet - Page 1
.... The TEGS4000i modular design provides greater flexibility for demanding network environment. Expandability: Install more modules to further segmenting the network.
The TEG-S4000i features advanced network features such as SNMP, VLAN, and QoS making it an ideal component for up to 4 modules that meet your network environment. Flexibility: Accepts up to specific network media...
Data Sheet - Page 2
... Brands and product names are trademarks of service, IEEE 802.1Q VLAN Tagging, RFC ...TRENDnet is a registered trademark. UTP/STP Cat. 5, EIA/TIA-568 100-ohm, 100 meters max. - 62.5/125µm Multimode Fiber with SC-type (or MT-RJ) connector, 2Km max. - 8,9/125µm Single-Mode Fiber with SC-type connector, 10Km max. All Rights Reserved. 4-Slot SNMP Modular Switch
TEG-S4000i
SPECIFICATIONS...
Manual - Page 2
MAC: 4K
Buffer:256Kbytes
2. 2/4/8 100FX (48310 ) spec. Gigabit module (48360) MAC:4K,
Buffer 128 Kbytes
QA
PM
Richard
2 MAC12k, Buffer:5Mbytes
3. Release Note
4 slot modular switch manual
Update
Version
23/04/2003 V2.0
Progress status
Remark
On checking 1. 10/100 TX (48350) spec.
Manual - Page 6
..., you can use Telnet to 4095 VLANs ) IEEE 802.1d Spanning Tree Protocol ( STP ) Statistic Address Table for manual address-addition Port Trunking supported IGMP supported Broadcast Storm Filter Port Mirror Web Browser Security Firmware upgradeable trough TFTP MIB II and Private MIB supported IEEE 802.1p QoS, ToS Port Security
Management Methods
The Modular Switch...
Manual - Page 10
... plug and On/off switched are located at the Rear Panel of the switch. LED
Status
Meaning
Power
Green
Power on
Diag
Red
Alert and problem notice
LK/ACT
Green Blinks
Device has been connected to other devices and networks are located on the port
Off
No device attached or in...
Manual - Page 11
... to other ports. Spanning Tree
Spanning Tree Protocol (STP) is used . The IEEE 802.1d Spanning Tree Protocol support for data transport while operating in switched networks.
For more than one path exists between parts of a network, only one of -band management means go through the RS-232 port. This also permits...
Manual - Page 12
... same broadcast domain. cast traffic and increase security, so as belonging to protect their physical location, and does not require recabling. Available copper links and supported distances are hardware and/or software processes reporting activity in each station.
SNMP
( Simple Network Management Protocol ) A widely-used to trunk multiple lower speed links...
Manual - Page 13
...is only packet that with pre-defined MAC address will continue to receive the multicast service.
This feature prevents the bursts of target port. The switch looks up the IP ...) on each port.
It allows user by manual input the MAC address table.
Port Security
Port Security allow you to restrict specific MAC addresses to support real-time applications such as video conferencing or ...
Manual - Page 16
Departmental Bridge Application NOTE: Full-duplex operation only applies to point-to a workstation, server, or another switch). When connecting to hubs, use a standard cascaded connection set for example, when attaching the switch to -point access (for half-duplex operation.
16 Figure 3-2.
Manual - Page 26
... Gateway is finished resetting. For example, type "1" and "2" to Save the previous settings, and then Reboot the switch. Port Setting
This function is for the switch, and press Enter. ( Default IP address is 192... ) Select Default Gateway on the Device page, and enter a unique IP address for port speed setup.
You may have to press Enter again when the switch is 192.168.16.254 ) Remember ...
Manual - Page 32
... an embedded HTML web site residing in the Location or Address field. The Web-Based Management supports Internet Explorer 5.0 and later versions. It is 192.168.16.1 ) in flash memory. ...access speed and present an easy viewing screen. The user has to explicitly modify the browser setting to enable Java Applets to open sockets.
It offers advanced management features and allow Java Applets ...
Manual - Page 47
...support this field. Please check the corresponding mapping checkbox to assign a high priority or uncheck that to the packet received from 0 to 63) are also known as the DiffServ Code Point "DSCP" field, value from this function of a port is extremely important with the deployment of Service... IPv4 header and identify the Type-Of-Service byte (TOS field). This feature provides Quality...
Manual - Page 48
... in multicast communication network applications where one or more servers, for example, video servers, generate multicast traffic. Figure 5-12 The IGMP page
48
Type of Service
IGMP (IP Multicast)
IGMP is enabled, then the IP multicast traffic will have a higher priority than other traffic. Port Priority - If you want your switch...
Manual - Page 67
... both ends of overlapping.
The following example show you how to transmit tagging frame.
Remember to select Port 4 and Port 5 for the purpose of a link support IEEE 802.1Q. Now you have create two VLAN Groups ( Group1 VID=1 and Group2 VID=2 ) with one common tagged port.
.BY4XJUDI**.
(SPVQ7*%
(SPVQ7*%
(SPVQ7*%
$POOFDU...
Manual - Page 70
... you of updated technical and service information of services. Before contact your local dealer or service contact on the Registration card, describe the problem, and ask for troubleshooting. Please follow below steps to the fax number on the card, or you can return the hardware for a better description: Symptoms, error messages, frequency, product model name, serial number, part number...
TRENDnet TEG-S4000i Reviews
We have not received any reviews for TRENDnet yet.