TRENDnet TE100-S24WS Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TE100-S24WS manuals!
Problems with TRENDnet TE100-S24WS?
Ask a Question
Free TRENDnet TE100-S24WS manuals!
Problems with TRENDnet TE100-S24WS?
Ask a Question
Popular TRENDnet TE100-S24WS Manual Pages
Manual - Page 6
Monitor List 17 Device Setting 19 Toolbar 20 Configuring the Switch 21 Login 22 Main Menu 24 Configuring Setup Setting 24
Port Settings 24 VLAN Settings (Virtual Local Area Network 26 Device Status 27 Statistic 27 System Setting 28 Trap Setting 29 Set Password 30 Backup Setting 30 Reset Setting 31 Logout 31 Technical Specifications 33
ii
Manual - Page 10
...setup and maintenance required make routers relatively impractical. Routers have also been used to another. Switching is a cost-effective way of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments. The switch... area network congestion problems.
4 Switching LAN technology is multiplied, while still maintaining the same network cabling and adapter cards...
Manual - Page 11
... in the Switch. Cost Reduction, VLANs can communicate as if a common broadcast domain, a LAN.
Features
u 24×10/100Mbps Auto-negotiation Ethernet ports u All ports support auto MDI/MDIX...mode for each port u Wire speed reception and transmission u Store-and-Forward switching scheme capability to support rate
adaptation and ensure data integrity u Up to 4K unicast addresses entities per...
Manual - Page 12
u Supports Back-pressure flow control for half-duplex mode ports u Supports Port-setting for Speed/Disable, Flow control u Supports port-base VLAN u Supports port-base QoS u Optional one port 100BASE-FX Fiber module in the rear panel
for length extension u Easy configuration via WEB Browser u Easy setting via Web Management Utility u Standard 19" Rack-mount size
6
Manual - Page 14
... provided with the equipment rack to the bottom of each switch in a wiring closet with the provided screws.
Install the Switch on rack installation, see the next section, Rack Mounting. For information on a sturdy, level surface that can be placed in the rack.
When installing the Switch on each side), and secure them with other equipment.
Manual - Page 15
... automatically and may be turned on without worrying if you are Auto-MDI type port. The switch's power supply will adjust to the AC power connector and the system fan. Connecting Network Cable
The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both in half and full duplex mode. The...
Manual - Page 17
... front panel, rear panel, and LED indicators of the Switch. These ports also supports automatic MDI/MDIX crossover detection function gives true "plug and play" capability, just need to "Forced Mode", the Auto MDI/MDIX will be disabled.
11 Note: When the port was set to plug-in half-
duplex transfer modes. Figure 3.
Manual - Page 18
... of the provided power cord into this connector, and the male into the slot.
Supported input voltages range from 100-240V AC at 50-60Hz. Reset: The Reset button is a three-pronged connector that you recorded the setting of the Switch
100Base-FX Fiber Module Slot
This is the slot when the users need to...
Manual - Page 21
Installing the Web Management Utility
The following gives instructions guiding you can configure the Switch such as VLAN, Port Setting, and System Setting ...etc. From the Start menu on -screen instructions to Program Files -> web_management_utility and execute the Web Management utility. (Figure 6.)
15 In the Run dialog box, type D:\Web Management
Utility\setup.exe (D:\ depends where...
Manual - Page 24
... to receive Trap information, switch has to monitor. When the "View Trap" button is no trap transmitted, and else when it indicates in the Monitor List.
18 Add Item: To add a device to the Monitor List manually, enter the IP Address... 7.
View Trap: The Trap function can receive the events that happen from the Web Management Switch in the Trap Setting Menu (see Page 33 for detail).
Manual - Page 26
Firmware Upgrade: When the device has a new function, there will auto load the default recorded setting. Monitor Save As: To record the setting of the Monitor List.
In the "File TAB", there are Monitor Save, Monitor Save As, Monitor Load and Exit. Toolbar
The toolbar in Web browser. Figure 11. Monitor Load: To manually load the...
Manual - Page 27
... the Switch
The 24-Port 10/100Mbps Fast Ethernet Web Smart Switch has a Web GUI interface for smart switch configuration. The Switch can manage, control and monitor the switch from the... Port Setting (Speed, duplex mode, flow control and QoS) u Virtual LAN Group setting (VLAN) u System IP address and password setting u Device status (System status, Port status, Port statistic and
VLAN status...
Manual - Page 30
..., QoS priority and Link Status. Main Menu
When the main page appears, find the Setup menu in the Main Menu screen. Figure 15. Click on the setup item that there are nine options: Port Settings, VLAN Settings, Device Status, Statistic, System Settings, Trap Setting, Password Setting, Backup Setting and Reset Setting as shown in the left side of the screen (Figure 15).
Manual - Page 32
... Switch will always transfer their own to execute the setting. Set FlowCtrl to manage the data transfer, QoS should be change. there is set to forced mode, then the flow control will automatically set to Disable; QoS: In some ports that need to have a high priority to Enable for avoiding data transfer overflow. To add a VLAN...
Manual - Page 36
.... u Copper Port Events: Monitoring the copper port status. If you to sent a trap when there are receive data error in the rear panel of the Switch. Abnormal* Transmit Error: to backup the current setting of the Switch, the current setting includes VLAN, Port Setting ... Set Password Backup Setting The backup tools help you forget the password, press the "Reset" button in copper port.
TRENDnet TE100-S24WS Reviews
We have not received any reviews for TRENDnet yet.