TRENDnet TE100-S24V Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TE100-S24V manuals!
Problems with TRENDnet TE100-S24V?
Ask a Question
Free TRENDnet TE100-S24V manuals!
Problems with TRENDnet TE100-S24V?
Ask a Question
Popular TRENDnet TE100-S24V Manual Pages
Data Sheet - Page 1
...TE100-S24V (11-17-2002)
Performance: Provides non-blocking high performance with 4K entries MAC address table Support Port setting function allow user setting each port Wire Speed reception and transmission Store and Forward switching method Supports...Warranty
BENEFITS
Easy Upgrade: Ethernet workgroups are able to upgrade to meet their high bandwidth requirements. TRENDnet
TRENDware, USA
...
Data Sheet - Page 2
...1100
R
Fax: 310-891-1111
TRENDnet
Web: www.TRENDNET.com
TRENDware, USA
Email: [email protected]
TRENDnet is subject to TRENDware products and ...
Torrance, CA. 90505. Copyright © TRENDware International, Inc. 2004. All Rights Reserved. TE100-S24V
24-port 10/100Mbps Smart Switch
SPECIFICATIONS
LAN Standards: • IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, 100Base-FX
Network...
Manual - Page 6
CONFIGURING SETUP SETTINGS 17 CONFIGURING SYSTEM SETTING 22 CONFIGURING FILE SETTING 23 STATISTICS 25
TECHNICAL SPECIFICATIONS 27
Manual - Page 10
...LAN segments.
Today switches are an ideal solution to most kinds of local area network congestion problems.
VLAN (Virtual Local Area Network)
A VLAN is a group of network bridges, which ...to pushing beyond the limits of Ethernet technology is the development of a router, the setup and maintenance required make routers relatively impractical. Routers have also been used to segment local ...
Manual - Page 12
...mode for each port Wire speed reception and transmission Store-and-Forward switching scheme capability to support rate adaptation and ensure data integrity Broadcast storm protection Up to 4K unicast addresses entries per... module with SC type connector in the rear panel Supports Port-based VLAN and IEEE 802.1p QoS RS-232 DCE console port for setting up and manage the Switch via connection to a ...
Manual - Page 15
...FX
F DX
Figure 1.
The Switch can make a connection using a standard or crossover cable.
9 Installing the bracket with the provided screws
Then, use screws provided with the equipment rack to mount the ...Switch on to the rack
Connecting Network Cable
The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both in half and full duplex mode...
Manual - Page 17
..." capability. Console Port An RS-232 DCE console port is a three-pronged connector that supports the power cord. Rear panel of the provided power cord into this connector, and the male...Windows HyperTerminal). These ports support network speeds of either 10Mbps or 100Mbps, and can operate in the female connector of the Switch
AC Power Connector This is used to setup and manage the Switch via...
Manual - Page 21
...:
Setup The two options in the Setup screen are available in the System screen; Navigating The Console After entering the configuration program, you can upload or download the Switch's configuration settings by using the console program.
Factory Reset, Change Password, Confirm Password, ... port's data transferring and receiving status. Below are illustrated in the File setting screen.
Manual - Page 23
... four options in the lower portion of the screen. Main Menu
Configuring Setup Settings
There are Setup, System, File, and Statistics. Figure 11. Main Menu
After login ...17
You can see the available console command keys in the Main Menu screen are Port Configuration and VLAN settings in Setup menu (see Figure 11). Move cursor to highlight a desired option by using Up Arrow, Down Arrow...
Manual - Page 24
This screen displays Port 01 ~ 12 status, for optional Fiber Port) Speed, Flow Control, and QoS. After completing the setup, move cursor to Save and hit Enter to save the settings.
18 Setup Menu
Port Configuration In Port Configuration menu (Figure 13), you can configure each port's (port 25 is determined by the Switch...
Manual - Page 25
... to network congestions. When data packets with QoS priority information pass through QoS supported device, these packets will
19 Set FlowCtrl to ON to select one of Service (QoS) is higher than 3, the packet has high priority; To change the speed setting, highlight Port, enter the port number and hit Enter, and the cursor...
Manual - Page 26
...other. Each v (or - ) represents a port; To setup VLAN, enter the VLAN group number and you can set Port 1 ~ 5 QoS to High and set to low priority, but the packet coming in the same VLAN ... the packet according to the priority code (high or low) of ports into individual "virtual" network. Note: IEEE 802.1p Priority Tag supersedes the Port-Based Priority setting. Use [Tab] and [Backspace]...
Manual - Page 27
... Switch's port 1~5.
Bar] to select "V" to add the port to the VLAN group or select "" to VLAN 1 (see Figure 14). VLAN1
1
2
3
4
X
VLAN2
2
3
4
5
21 In this setup, PC1 could not communicate with PC5, because they are not in the same VLAN group.
Figure 14. In default, all ports belong to delete the...
Manual - Page 28
... group is independent and there is no communication between PC1 (VLAN 1) and PC5 (VLAN 2)
Using VLAN feature, you can be very confusing. If your VLAN settings do not perform the way they should, you can group the computers on the Switch into many independent small networks. X
X
VLAN1
VLAN2
VLAN3
Figure 16...
Manual - Page 29
... change the login password (maximum 20 digits / letters). Confirm Password: To confirm the new password. The selections are Disabled, 1 min., 2 min., 3 min., 4 min., and 5 min. Figure 17. System Setting
Configuring File Setting
You can select Disabled, 1 sec., 5 sec., 10 sec., 15 sec., or 20 sec. (by pressing the [Space bar]). You can upload (save) or...
TRENDnet TE100-S24V Reviews
We have not received any reviews for TRENDnet yet.