TRENDnet TE100-S16R Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TE100-S16R manuals!
Problems with TRENDnet TE100-S16R?
Ask a Question
Free TRENDnet TE100-S16R manuals!
Problems with TRENDnet TE100-S16R?
Ask a Question
Popular TRENDnet TE100-S16R Manual Pages
User Guide - Page 5
... OF CONTENTS
ABOUT THIS GUIDE III
PURPOSE III TERMS/USAGE III OVERVIEW OF THIS USER'S GUIDE III
INTRODUCTION 1
FAST ETHERNET TECHNOLOGY 1 SWITCHING TECHNOLOGY 2 FEATURES 3
UNPACKING AND INSTALLATION 5
UNPACKING 5 INSTALLATION 5 RACK MOUNTING 6
IDENTIFYING EXTERNAL COMPONENTS
...7
FRONT PANEL 7 REAR PANEL 8 LED INDICATORS 9 TRUNKING SETTING 9 QOS (QUALITY OF SERVICE) SETTING 12
i
User Guide - Page 7
...
In this User's Guide
Introduction. Technical Specifications.
Identifying External Components. Describes the front panel, rear panel and LED indicators of the Switch. Lists the technical (general, physical and environmental, and performance) specifications of the Switch.
Unpacking and Installation. Tells how you get started with the basic installation of the 16-Port 10/100Mbps NWay...
User Guide - Page 10
... has its own bandwidth and it possible to setup, and
2
Routers have also been used to split parts of switching technology. Switching is the development of the network into different segments. The switch forwards traffic from origin segment to pushing beyond the 205-meter network diameter limit. The switch supports both traditional 10Mbps Ethernet and 100Mbps Fast...
User Guide - Page 11
... the highest bandwidth at 200Mbps (100Mbps full-duplex mode), each port. It also controls the data flow between transmit and receive nodes to guarantee against all ports support 200Mbps, the Switch can be upgraded to large workgroups. Switch, on the other hand, is effectively allocated for each port can connect to a rapidly growing network through a wide range...
User Guide - Page 12
...Rate (per port) at wire-speed for cascading two or more Switches (same model).
4 This allows auto-sensing of complete frame
checking and error frame filtering, this scheme prevents error packages from ... with self-learning and table ageing. ??512KBytes RAM buffer per port basis. ??Supports two trunking groups for both 10Mbps and 100Mbps speed; Other key features are as followed...
User Guide - Page 13
... local reseller for replacement. Installation
The site where you install the Switch may greatly affect its contents. One the 16-Port 10/100Mbps NWay Ethernet Switch ?? Four rubber feet to be used for ventilation.
5 When installing, consider the following items: ?? Leave at least 10cm of space at the left and right hand side of the Switch for shock cushioning...
User Guide - Page 15
... to use ordinary straight-through twisted-pair cables to connect PCs, workstations, and Servers to the Switch. Twisted-Pair Ports Use any of the switch.
16-Port 10/100Mbps NWay Ethernet Switch
LED Indicator Panel Refer to another device's MDI-X port using the Uplink port (described below).
The LED indicator panel is shown, followed by a description of the...
User Guide - Page 16
... refer to the QoS Setting in the next section. QoS setting DIP switch: By using the trunking DIP switches, you can set the QoS function. Rear Panel
Trunking setting DIP switch: By using the QoS DIP switches, you can set the trunking function.
For detail information on how to setup QoS, please refer to the Trunking Setting in the next section...
User Guide - Page 17
This LED blinks green when collision occurs on the 10Mbps network. It blinks amber when transmitting or receiving data on the respective port. Trunking setting
This Switch supports trunking function. You can cascade two Switches via one trunking group (max. LED Indicators
Power (Power Indicator) This indicator lights green when the hub is connected to a 100Mbps...
User Guide - Page 18
...B1
Trunking Group B
0 0 Disable
1 0 Port 8, 16 (400Mbps) 0 1 Port 8, 15 & 16 (600Mbps) 1 1 Port 7, 8, 15 & 16 (800Mbps)
You can only trunk same model Switches together.
1. Follow the table above to select the trunk ports and set the trunking
dipswitches:
Note: You can select to set the
dipswitches. 3. Please follow the instructions below to trunk two Switches using crossover CAT5 UTP...
User Guide - Page 19
Cascade two switches with UpLink port Cascade two switches with Trunking ports
Cascade three switches with trunking ports 11
User Guide - Page 20
...Port-Based Priority is a networking term that specifies a guaranteed throughput level. When data packets with priority. This Switch supports leading edge QoS with precedence for user to set...supported device, these packets will be checked via layer 2 (IEEE802.1Q VLAN Tagging) and/or layer 3 (IP Header TOS bits). Port based priority ensures transmission with three levels of Service...
User Guide - Page 23
... the connection is in half-duplex mode.
The "FDX/COL LED" indicator lights green if the LAN
adapter is made, the port LED on the Switch will show the status of the 16 port s (1x - 16x)
Note: Use CAT5 (or better) cable for PC to your Fast Ethernet network.
The "LINK/ACT" LED indicator...
User Guide - Page 24
"LINK/ACT" LED indicator lights green. Hub without Uplink (MDI-II) port
If a hub is not equipped with an uplink (MDI-II) port, connection can be made from any regular ports of the Switch to any port of the Hub.
16 B.
A.
"LINK/ACT" LED indicator lights amber. Using crossover cable
When using either straight cable or crossover...
User Guide - Page 25
... green if the connection is done from the Switch's uplink (MDI-II) port (Switch A) to any of the 10Mbps, 100Mbps (MDI-X) port of the other switch (switch B) or other devices (routers, bridges, etc...support auto-negotiation or has auto-negotiation disabled, an auto-sensing process is in full-duplex mode.
The LED remains off when the connection is initiated to select the speed and set...
TRENDnet TE100-S16R Reviews
We have not received any reviews for TRENDnet yet.